Home › ENGINE ยท 1KD-FTV › COOLING › WATER PUMP (w/ EGR Cooler)

WATER PUMP (w/ EGR Cooler) > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.



2. REMOVE NO. 1 ENGINE UNDER COVER (for 4WD)
  1. Remove the 4 bolts and cover.



3. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



    A099591E01
  1. Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.



  1. Loosen the cylinder block drain cock plug.


    A147246E01



4. DISCONNECT RADIATOR HOSE INLET


5. REMOVE FAN SHROUD


A099548E01
  1. Remove the 3 bolts and oil reservoir.

  1. Disconnect the No. 1 and No. 2 water by-pass hoses from the tank upper and lower.

  1. Remove the 2 bolts and radiator reservoir.

  1. Loosen the 4 nuts holding the fluid coupling fan.

  1. Remove the drive belt .

  1. Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the water pump.



6. REMOVE COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)


    I043250E01
  1. Disconnect the connector.



    I043253E01
  1. Remove the 4 bolts and compressor.



7. REMOVE GENERATOR ASSEMBLY


A111821
  1. Remove the nut and generator wire.

  1. Disconnect the generator connector.

  1. Remove the 2 bolts and generator.



8. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


A098937E01
  1. Remove the 4 bolts and belt tensioner.



9. REMOVE EGR COOLER WITH ELECTRIC EGR CONTROL VALVE AND NO. 2 EGR VALVE
  1. Remove the EGR cooler (Click here).



10. REMOVE NO. 4 INJECTION PIPE


    A152275
  1. Remove the bolt and disconnect the injection pipe clamp.



    A152276E02
  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.



11. REMOVE VENTILATION PIPE


    A151169
  1. Remove the bolt and ventilation pipe.



12. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    G034877E01
  1. Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.



13. REMOVE NO. 1 TIMING BELT COVER


A015094E01
  1. Remove the bolt and water hose clamp.

  1. Remove the wire harness clamp.

  1. Remove the 6 bolts and timing belt cover.



14. REMOVE TIMING BELT


A070549E02
  1. Turn the crankshaft clockwise and align the timing marks as shown in the illustration.



    A070550E01
  1. Uniformly loosen the 2 bolts and remove the timing belt tensioner.

  1. Remove the timing belt.

  1. Using a 10 mm hexagon wrench, remove the bolt, timing belt idler and washer.

    HINT:

    1. A070551E02
    2. When turning the camshaft while the timing belt is removed, turn the crankshaft 90° counterclockwise.
    3. When installing the timing belt, return the camshaft to the timing marks and then turn the crankshaft clockwise until it aligns with the timing marks, as shown in the illustration.



15. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY


16. REMOVE CAMSHAFT TIMING PULLEY


    A060182E01
  1. Remove the bolt of the camshaft timing pulley by holding the camshaft with a wrench.

    NOTICE:
    Make sure to remove the bolt of the camshaft timing pulley with the timing belt not installed.

  1. Remove the camshaft timing pulley.



17. REMOVE NO. 2 TIMING BELT COVER
  1. Remove the 4 bolts, nuts and timing belt cover.



18. REMOVE CYLINDER BLOCK INSULATOR


    A149941
  1. Remove the cylinder block insulator from the head.



19. REMOVE WATER PUMP ASSEMBLY


    A225339
  1. Remove the 2 nuts, 5 bolts, water pump and gasket.