Home › ENGINE ยท 5L-E › LUBRICATION › OIL PUMP

OIL PUMP > REMOVAL

for Preparation Click here



1. REMOVE ENGINE ASSEMBLY
  1. Remove the engine assembly (Click here).



2. REMOVE TIMING BELT
  1. Remove the timing belt (Click here).



3. REMOVE INJECTION PIPE SUB-ASSEMBLY


    A121940E01
  1. Using SST, loosen the 8 union nuts of the 4 injection pipes.

    SST
    09023-12701  

  1. Remove the 2 nuts, 2 upper pipe clamps and 4 injection pipes with lower pipe clamps.



4. REMOVE INJECTION PUMP DRIVE PULLEY


    A071313E01
  1. Using SST, remove the pulley nut.

    SST
    09213-14010   (91651-60865)
    09330-00021  



    A071314E01
  1. Using SST, remove the drive pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)



5. REMOVE INJECTION PUMP ASSEMBLY


    A121086E01
  1. Disconnect the engine speed sensor connector.

  1. Disconnect the spill control valve connector.

  1. Disconnect the correction unit connector.

  1. Disconnect the timing control valve connector.

  1. Disconnect the fuel temperature sensor connector.

  1. Disconnect the engine wire clamp.

  1. Disconnect the 3 fuel hoses.



    A071318E01
  1. Remove the 3 bolts and injection pump stay.

  1. Remove the 2 nuts and injection pump.



6. REMOVE CAMSHAFT TIMING PULLEY


  1. Set the No. 1 cylinder to approx. 90° BTDC/compression.

    HINT:
    Set the No. 1 cylinder to 90° BTDC/compression to avoid interference with the piston top and valve head.




      A057443E03
    1. Using the crankshaft pulley bolt, turn the crankshaft 90°counterclockwise, and put the timing mark of the crankshaft timing pulley with the protrusion of the timing belt case.



    A056901E02
  1. Using SST, loosen the pulley bolt.

    SST
    09960-10010   (09962-01000, 09963-01000)



    A056903E02
  1. Using SST, disconnect the timing pulley from the camshaft.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)

  1. Remove the pulley bolt and timing pulley.

  1. Remove the timing pulley woodruff key.



7. REMOVE NO. 2 TIMING BELT COVER
  1. Remove the 4 bolts and timing belt cover.



8. REMOVE WATER PUMP ASSEMBLY


    A031001E01
  1. Remove the 6 bolts and tension spring bracket.

  1. Remove the water pump and gasket.



9. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY


    A056838E06
  1. Remove the 2 bolts (A and B).

  1. Loosen the bolt (C), and remove the No. 1 timing belt idler.



10. REMOVE NO. 2 TIMING BELT IDLER SUB-ASSEMBLY
  1. Remove the bolt, No. 2 timing belt idler and spacer.



11. REMOVE CRANKSHAFT TIMING PULLEY


    A056898E03
  1. Using SST, remove the timing pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09953-05020, 09954-05010)



12. REMOVE OIL PAN SUB-ASSEMBLY
  1. Remove the 16 bolts and 2 nuts.



    A057637E02
  1. Insert the blade of SST between the oil pan and cylinder block, cut off the applied sealer and remove the oil pan.

    SST
    09032-00100  

    NOTICE:
    1. Do not use SST for the timing belt case side and rear oil seal retainer.
    2. Be careful not to damage the oil pan flange.



13. REMOVE OIL STRAINER SUB-ASSEMBLY
  1. Remove the 2 bolts, 2 nuts, oil strainer and gasket.



14. REMOVE TIMING BELT CASE SUB-ASSEMBLY


    A056912E01
  1. Remove the 5 bolts, timing belt case and gasket.