ENGINE UNIT > REASSEMBLY |
| 1. INSTALL TIGHT PLUG |
![]() |
Apply adhesive to the end of a new tight plug.
Position A:
Using a 14 mm steel bar and hammer, tap in the tight plug as shown in the illustration.
Other Positions:
Using SST and a hammer, tap in a new tight plug as shown in the illustration.
Position B

| 2. INSTALL STUD BOLT |

| 3. INSTALL STRAIGHT PIN |

| 4. INSTALL RING PIN |

| 5. INSTALL NO. 1 STRAIGHT SCREW PLUG |
Install a new gasket and the screw plug.
| 6. INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY |
![]() |
Align the pin of the oil nozzle with the pin hole of the cylinder block.
Install the 4 oil nozzles together with the check valves.
| 7. INSTALL PISTON PIN |
Assemble the piston and connecting rod.
![]() |
Using a small screwdriver, install a new snap ring on one side of the piston pin hole.
![]() |
Gradually heat the piston to about 80°C (176°F).
![]() |
Coat the piston pin with engine oil.
Align the front marks of the piston and connecting rod, and push in the piston pin with your thumb.
![]() |
Check the fit between the piston and piston pin. Try to move the piston back and forth on the piston pin.
![]() |
Using a small screwdriver, install a new snap ring on the other side of the piston pin hole.
![]() |
Install the piston rings.
Install the coil and oil ring by hand.
![]() |
Using a piston ring expander, install the No. 1 and No. 2 piston rings with the code mark facing upward.
| Number | Mark | |
| No. 1 | w/ EGR Cooler | NPR |
| w/EGR System without EGR Cooler | NKD | |
| w/o EGR System | NAB | |
| No. 2 | w/ EGR System | N |
| w/o EGR System | ND1 | |
![]() |
Position the piston rings so that the ring ends are as shown.
| 8. INSTALL CONNECTING ROD BEARING |
![]() |
Align the bearing claw with the groove of the connecting rod or connecting cap.
Install the bearings to the connecting rod and connecting rod cap.
| 9. INSTALL CRANKSHAFT BEARING |
![]() |
Align the bearing claw with the claw groove of the cylinder block, and push in the 5 upper bearings.
Align the bearing claw with the claw groove of the crankshaft bearing cap, and push in the 5 lower bearings.
| 10. INSTALL CRANKSHAFT |
![]() |
Place the crankshaft on the cylinder block.
Install the 2 upper thrust washers to the No. 5 journal position of the cylinder block.
Push the crankshaft toward the front (rear) side.
Install the 2 thrust washers with the oil grooves facing outward.
![]() |
Install the 2 thrust washers on the No. 5 bearing cap with the grooves facing outward.
![]() |
Install the 5 crankshaft bearing caps in their proper locations.
![]() |
Install the crankshaft bearing cap bolts.
Apply a light coat of engine oil to the threads and under the bolt heads of the main bearing caps.
Install and uniformly tighten the 10 bolts of the main bearing caps in several passes in the sequence shown in the illustration.
![]() |
Mark the front of the main bearing cap bolts with paint.
Retighten the main bearing cap bolts 90° in the numerical order shown above.
Check that the painted marks are now at a 90° angle to the front.
Check that the crankshaft turns smoothly.
Check the crankshaft thrust clearance.
| 11. INSTALL PISTON AND CONNECTING ROD |
![]() |
Using a piston ring compressor, push the correctly numbered piston and connecting rod assembly into the cylinder with the front mark of the piston facing forward.
![]() |
Place the connecting rod cap on the connecting rod.
Match the numbered connecting rod cap with the connecting rod.
Align the pins of the connecting rod cap with the pin holes of the connecting rod, and install the connecting rod cap.
![]() |
Check that the front mark of the connecting rod cap is facing forward.
![]() |
Install the connecting rod cap bolts.
Apply a light of engine oil on the threads and under the heads of the connecting rod cap bolts.
Install and alternately tighten the bolts of the connecting rod cap in several passes.
![]() |
Mark the front of the connecting rod cap bolts with paint.
Retighten the connecting rod cap bolts 90° as shown.
Check that the painted marks are now at a 90° angle to the front.
Check that the crankshaft turns smoothly.
Check the connecting rod thrust clearance .
| 12. INSTALL CYLINDER BLOCK OIL ORIFICE |
| 13. INSTALL SUPPLY PUMP GEAR BEARING |
![]() |
Using SST and a press, press in a new bearing.
| 14. INSTALL ENGINE REAR OIL SEAL RETAINER |
![]() |
Remove any old packing (FIPG) material.
Apply seal packing to the specific places described in the illustration.
![]() |
Install the retainer with the 5 bolts. Alternately tighten the 5 bolts in several passes.
| 15. INSTALL NO. 2 BALANCE SHAFT DRIVEN GEAR |
![]() |
Mount the balance shaft between aluminum plates in a vise.
Align the balance shaft knock pin with the knock pin hole. Then install the balance shaft thrust washer and balance shaft driven gear.
Install the bolt.
| 16. INSTALL NO. 2 BALANCE SHAFT SUB-ASSEMBLY |
![]() |
Install the balance shaft with the 2 bolts.
| 17. INSTALL NO. 1 BALANCE SHAFT DRIVEN GEAR |
![]() |
Mount the balance shaft between aluminum plates in a vise.
Align the balance shaft knock pin with the knock pin hole. Then install the balance shaft thrust washer and balance shaft driven gear.
Install the bolt.
| 18. INSTALL NO. 1 BALANCE SHAFT SUB-ASSEMBLY |
![]() |
Install the balance shaft with the 2 bolts.
| 19. INSTALL TIMING GEAR CASE ASSEMBLY |
Remove any old packing (FIPG) material.
![]() |
Apply seal packing to the timing gear case as shown in the illustration.
![]() |
Install a new gasket to the groove of the timing gear case.
![]() |
Install 2 new O-rings to the cylinder block groove of the timing gear case.
![]() |
Align the "2" marks of the balance shaft driven gear No. 1 and oil pump drive gear.
Align the mark on the oil pump drive gear with the mark on the timing gear case.
![]() |
Install the timing gear case with the union bolt and 8 bolts.
![]() |
Remove the screw plug.
Pour in approximately 20 cc (0.12 cu in.) of engine oil into the oil pump.
Install a new gasket and the screw plug.
| 20. INSTALL OIL STRAINER SUB-ASSEMBLY |
Install a new gasket and the oil strainer with the 2 bolts and 2 nuts.
| 21. INSTALL OIL PAN SUB-ASSEMBLY |
![]() |
Remove any old packing (FIPG) material.
Apply seal packing to the oil pan as shown in the illustration.
Install the oil pan with the 22 bolts and 2 nuts.
Install the oil level gauge sensor with the 4 bolts.
| 22. INSTALL CRANKSHAFT TIMING GEAR OR SPROCKET |
![]() |
Face the crankshaft timing gear with timing mark 1 facing forward.
Align the set key on the crankshaft with the key groove of the crankshaft timing gear.
Using SST and a hammer, tap in the timing gear.
| 23. INSTALL SUPPLY PUMP GEAR |
Install the supply pump with the 2 nuts.
![]() |
Align the "3" marks of the balance shaft driven gear No. 2 and supply pump gear.
![]() |
Install a new O-ring to the supply pump gear.
![]() |
Install the supply pump gear set nut.
Using SST, tighten the nut.
| 24. INSTALL NO. 2 IDLE SUB GEAR |
![]() |
Mount the No.1 idle gear in a vise.
![]() |
Install the idle gear spring.
Install the No. 2 idle sub-gear.
Install the wave washer.
![]() |
Using snap ring pliers, install the snap ring.
![]() |
Using SST, align the holes of the No. 1 idle gear and No. 2 idle sub gear by turning the No. 2 idle sub gear clockwise, and install a service bolt.
Remove the No. 1 idle gear from the vise and turn it upside down.
| 25. INSTALL NO. 1 IDLE SUB GEAR |
![]() |
Mount the No. 1 idle gear and No. 2 idle sub gear in a vise.
![]() |
Remove the service bolt.
![]() |
Install the idle gear spring.
Install the No. 1 idle sub gear.
Install the wave washer.
![]() |
Using a snap ring pliers, install the snap ring.
![]() |
Using SST, align the holes of the No. 1 idler gear and No. 1 idle sub gear by turning the No. 1 idle sub gear clockwise, and install the service bolt.
| 26. INSTALL NO. 1 IDLE GEAR |
![]() |
Install the gear shaft as shown in the illustration.
![]() |
Align the "5" timing marks of the idle gear and crankshaft timing gear.
Using SST, turn the supply pump gear, and align the "4" timing marks of the idle gear and supply pump gear, and mesh the gears.
![]() |
Face the thrust plate with the protrusion facing forward.
Align the bolt holes, and install the thrust plate with the 2 bolts.
Remove the service bolt.
| 27. INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE |
![]() |
Align the set key with the key groove of the sensor plate.
Install the sensor plate, facing the cup side outward.
| 28. INSTALL TIMING GEAR CASE ASSEMBLY |
Remove any old packing (FIPG) material.
![]() |
Apply seal packing to the timing gear cover as shown in the illustration.
![]() |
Install a new O-ring to the timing gear case.
![]() |
Install the timing gear cover with the 14 bolts and 2 nuts.
| 29. INSTALL WATER PUMP ASSEMBLY |
![]() |
Install a new gasket and the water pump with the 5 bolts and 2 nuts.
| 30. INSTALL CYLINDER HEAD SUB-ASSEMBLY |
Place the cylinder head on the cylinder head gasket.
Apply a light coat of engine oil on the threads and under the heads of the cylinder head bolts.
![]() |
Install and uniformly tighten the 18 cylinder head bolts, in several passes in the sequence shown in the illustration.
![]() |
Mark the front of the cylinder head bolts with paint.
Further tighten the cylinder head bolts by 90° in the sequence shown in the illustration above.
Finally, tighten the cylinder head bolts by an additional 90°.
Check that the painted marks are now facing rearward.
| 31. INSTALL CAMSHAFT |
![]() |
Using the crankshaft pulley bolt, set the No. 1 cylinder to 90° BTDC/compression.
![]() |
Install the camshaft.
Apply MP grease to the thrust portion of the camshaft.
Place the camshaft on the cylinder head, facing the key groove upward.
![]() |
Align the timing marks (1 dot mark) of the camshaft drive and driven main gears, and set the No. 2 camshaft in place.
![]() |
Remove any old packing (FIPG) material from the camshaft bearing cap.
Apply seal packing to the specified areas shown in the illustration.
![]() |
Install the 5 bearing caps in their proper locations.
![]() |
Apply a light coat of engine oil on the threads and under the heads of the bearing cap bolts.
Install and uniformly tighten the 15 bearing cap bolts in several passes in the sequence shown in the illustration.
Install the camshaft oil seal.
| 32. INSPECT VALVE CLEARANCE |
Drain coolant.
Remove the fan shroud.
Remove the No. 1 timing belt cover.
Remove the timing belt.
Remove the camshaft timing pulley.
Remove the No. 1 timing belt idler.
Remove the No. 2 timing belt cover.
Remove the camshafts.
Remove the valve lifters.
![]() |
Using a micrometer, measure the thickness of the removed lifter.
Calculate the thickness of a new lifter so that the valve clearance is within the specified range.
| A | B | C |
| New lifter thickness | Used lifter thickness | Measured valve clearance |
Select a new lifter with a thickness as close as possible to the calculated values.
Install the selected valve lifter.


| Lifter No. | Specified Condition | Lifter No. | Specified Condition | Lifter No. | Specified Condition |
| 06 | 5.060 mm (0.1992 in.) | 30 | 5.300 mm (0.2087 in.) | 54 | 5.540 mm (0.2181 in.) |
| 08 | 5.080 mm (0.2000 in.) | 32 | 5.320 mm (0.2094 in.) | 56 | 5.560 mm (0.2189 in.) |
| 10 | 5.100 mm (0.2008 in.) | 34 | 5.340 mm (0.2102 in.) | 58 | 5.580 mm (0.2197 in.) |
| 12 | 5.120 mm (0.2016 in.) | 36 | 5.360 mm (0.2110 in.) | 60 | 5.600 mm (0.2205 in.) |
| 14 | 5.140 mm (0.2024 in.) | 38 | 5.380 mm (0.2118 in.) | 62 | 5.620 mm (0.2213 in.) |
| 16 | 5.160 mm (0.2031 in.) | 40 | 5.400 mm (0.2126 in.) | 64 | 5.640 mm (0.2220 in.) |
| 18 | 5.180 mm (0.2039 in.) | 42 | 5.420 mm (0.2134 in.) | 66 | 5.660 mm (0.2228 in.) |
| 20 | 5.200 mm (0.2047 in.) | 44 | 5.440 mm (0.2142 in.) | 68 | 5.680 mm (0.2236 in.) |
| 22 | 5.220 mm (0.2055 in.) | 46 | 5.460 mm (0.2150 in.) | 70 | 5.700 mm (0.2244 in.) |
| 24 | 5.240 mm (0.2063 in.) | 48 | 5.480 mm (0.2157 in.) | 72 | 5.720 mm (0.2252 in.) |
| 26 | 5.260 mm (0.2071 in.) | 50 | 5.500 mm (0.2165 in.) | 74 | 5.740 mm (0.2260 in.) |
| 28 | 5.280 mm (0.2079 in.) | 52 | 5.520 mm (0.2173 in.) | - | - |


| Lifter No. | Specified Condition | Lifter No. | Specified Condition | Lifter No. | Specified Condition |
| 06 | 5.060 mm (0.1992 in.) | 30 | 5.300 mm (0.2087 in.) | 54 | 5.540 mm (0.2181 in.) |
| 08 | 5.080 mm (0.2000 in.) | 32 | 5.320 mm (0.2094 in.) | 56 | 5.560 mm (0.2189 in.) |
| 10 | 5.100 mm (0.2008 in.) | 34 | 5.340 mm (0.2102 in.) | 58 | 5.580 mm (0.2197 in.) |
| 12 | 5.120 mm (0.2016 in.) | 36 | 5.360 mm (0.2110 in.) | 60 | 5.600 mm (0.2205 in.) |
| 14 | 5.140 mm (0.2024 in.) | 38 | 5.380 mm (0.2118 in.) | 62 | 5.620 mm (0.2213 in.) |
| 16 | 5.160 mm (0.2031 in.) | 40 | 5.400 mm (0.2126 in.) | 64 | 5.640 mm (0.2220 in.) |
| 18 | 5.180 mm (0.2039 in.) | 42 | 5.420 mm (0.2134 in.) | 66 | 5.660 mm (0.2228 in.) |
| 20 | 5.200 mm (0.2047 in.) | 44 | 5.440 mm (0.2142 in.) | 68 | 5.680 mm (0.2236 in.) |
| 22 | 5.220 mm (0.2055 in.) | 46 | 5.460 mm (0.2150 in.) | 70 | 5.700 mm (0.2244 in.) |
| 24 | 5.240 mm (0.2063 in.) | 48 | 5.480 mm (0.2157 in.) | 72 | 5.720 mm (0.2252 in.) |
| 26 | 5.260 mm (0.2071 in.) | 50 | 5.500 mm (0.2165 in.) | 74 | 5.740 mm (0.2260 in.) |
| 28 | 5.280 mm (0.2079 in.) | 52 | 5.520 mm (0.2173 in.) | - | - |
Install the camshaft.
Install the No. 2 timing belt cover.
Install the No. 1 timing belt idler.
Install the camshaft timing pulley.
Install the timing belt.
Install the No. 1 timing belt cover.
Install the fan shroud.
Add engine coolant.
| 33. ADJUST VALVE CLEARANCE |
Drain coolant.
Remove the fan shroud.
Remove the No. 1 timing belt cover.
Remove the timing belt.
Remove the camshaft timing pulley.
Remove the No. 1 timing belt idler.
Remove the No. 2 timing belt cover.
Remove the camshafts.
Remove the valve lifters.
![]() |
Using a micrometer, measure the thickness of the removed lifter.
Calculate the thickness of a new lifter so that the valve clearance is within the specified range.
| A | B | C |
| New lifter thickness | Used lifter thickness | Measured valve clearance |
Select a new lifter with a thickness as close as possible to the calculated values.
Install the selected valve lifter.


| Lifter No. | Specified Condition | Lifter No. | Specified Condition | Lifter No. | Specified Condition |
| 06 | 5.060 mm (0.1992 in.) | 30 | 5.300 mm (0.2087 in.) | 54 | 5.540 mm (0.2181 in.) |
| 08 | 5.080 mm (0.2000 in.) | 32 | 5.320 mm (0.2094 in.) | 56 | 5.560 mm (0.2189 in.) |
| 10 | 5.100 mm (0.2008 in.) | 34 | 5.340 mm (0.2102 in.) | 58 | 5.580 mm (0.2197 in.) |
| 12 | 5.120 mm (0.2016 in.) | 36 | 5.360 mm (0.2110 in.) | 60 | 5.600 mm (0.2205 in.) |
| 14 | 5.140 mm (0.2024 in.) | 38 | 5.380 mm (0.2118 in.) | 62 | 5.620 mm (0.2213 in.) |
| 16 | 5.160 mm (0.2031 in.) | 40 | 5.400 mm (0.2126 in.) | 64 | 5.640 mm (0.2220 in.) |
| 18 | 5.180 mm (0.2039 in.) | 42 | 5.420 mm (0.2134 in.) | 66 | 5.660 mm (0.2228 in.) |
| 20 | 5.200 mm (0.2047 in.) | 44 | 5.440 mm (0.2142 in.) | 68 | 5.680 mm (0.2236 in.) |
| 22 | 5.220 mm (0.2055 in.) | 46 | 5.460 mm (0.2150 in.) | 70 | 5.700 mm (0.2244 in.) |
| 24 | 5.240 mm (0.2063 in.) | 48 | 5.480 mm (0.2157 in.) | 72 | 5.720 mm (0.2252 in.) |
| 26 | 5.260 mm (0.2071 in.) | 50 | 5.500 mm (0.2165 in.) | 74 | 5.740 mm (0.2260 in.) |
| 28 | 5.280 mm (0.2079 in.) | 52 | 5.520 mm (0.2173 in.) | - | - |


| Lifter No. | Specified Condition | Lifter No. | Specified Condition | Lifter No. | Specified Condition |
| 06 | 5.060 mm (0.1992 in.) | 30 | 5.300 mm (0.2087 in.) | 54 | 5.540 mm (0.2181 in.) |
| 08 | 5.080 mm (0.2000 in.) | 32 | 5.320 mm (0.2094 in.) | 56 | 5.560 mm (0.2189 in.) |
| 10 | 5.100 mm (0.2008 in.) | 34 | 5.340 mm (0.2102 in.) | 58 | 5.580 mm (0.2197 in.) |
| 12 | 5.120 mm (0.2016 in.) | 36 | 5.360 mm (0.2110 in.) | 60 | 5.600 mm (0.2205 in.) |
| 14 | 5.140 mm (0.2024 in.) | 38 | 5.380 mm (0.2118 in.) | 62 | 5.620 mm (0.2213 in.) |
| 16 | 5.160 mm (0.2031 in.) | 40 | 5.400 mm (0.2126 in.) | 64 | 5.640 mm (0.2220 in.) |
| 18 | 5.180 mm (0.2039 in.) | 42 | 5.420 mm (0.2134 in.) | 66 | 5.660 mm (0.2228 in.) |
| 20 | 5.200 mm (0.2047 in.) | 44 | 5.440 mm (0.2142 in.) | 68 | 5.680 mm (0.2236 in.) |
| 22 | 5.220 mm (0.2055 in.) | 46 | 5.460 mm (0.2150 in.) | 70 | 5.700 mm (0.2244 in.) |
| 24 | 5.240 mm (0.2063 in.) | 48 | 5.480 mm (0.2157 in.) | 72 | 5.720 mm (0.2252 in.) |
| 26 | 5.260 mm (0.2071 in.) | 50 | 5.500 mm (0.2165 in.) | 74 | 5.740 mm (0.2260 in.) |
| 28 | 5.280 mm (0.2079 in.) | 52 | 5.520 mm (0.2173 in.) | - | - |
Install the camshaft.
Install the No. 2 timing belt cover.
Install the No. 1 timing belt idler.
Install the camshaft timing pulley.
Install the timing belt.
Install the No. 1 timing belt cover.
Install the fan shroud.
Add engine coolant.
| 34. INSTALL INJECTOR ASSEMBLY |
![]() |
Install 4 new injection nozzle seats to the cylinder head.
Apply a small amount of clean engine oil to 4 new O-rings.
![]() |
Install an O-ring to each injector as shown in the illustration.
Insert the 4 injectors into the cylinder head.
For an injector that has been replaced with a new injector, register the injector compensation code .
![]() |
Temporarily install 4 new washers and the 4 No. 1 nozzle holder clamps with the 4 bolts.
![]() |
Temporarily install the 4 injection pipes with the union nuts.
![]() |
Check the nozzle leakage pipe. Check that there are no scratches or dents on the 5 union seal surfaces.
If scratches or dents are present, replace the nozzle leakage pipe.
![]() |
Set the leakage pipe and 5 new gaskets in place.
Apply a small amount of oil to the 4 injector hollow screws and union bolt.
![]() |
Temporarily install the leakage pipe with the 4 injector hollow screws and union bolt.
Tighten the 4 holder clamp bolts.
![]() |
Tighten the 4 injector hollow screws in order from 1 to 4.
Tighten the union bolt.
Remove the 4 injection pipes.
| 35. CHECK FOR FUEL LEAKS |
![]() |
Check that there are no leaks from the nozzle leakage pipe connection.
Install the gasket and No. 2 nozzle leakage pipe to the cylinder head with SST (check valve).
Apply a small amount of soapy water (or other fluid for detecting fuel leakage) on the nozzle leakage pipe connection.
![]() |
Install SST (turbocharger pressure gauge) to the fuel return side of the leakage pipe, and maintain 100 kPa (1.0 kgf/cm2, 14.5 psi) of pressure for 60 seconds to check that no bubbles form.
After checking for fuel leaks, wipe off the soapy water from the leakage pipe connection.
Remove SST, No. 2 nozzle leakage pipe and gasket.
| 36. INSTALL CYLINDER BLOCK INSULATOR (w/ EGR Cooler) |
Install the cylinder block insulator to the cylinder head.
| 37. INSTALL NO. 2 TIMING BELT COVER |
![]() |
Apply seal packing (FIPG) to the specified areas shown in the illustration.
Install the No. 2 timing belt cover with the 4 bolts and nut.
| 38. INSTALL CAMSHAFT TIMING PULLEY |
![]() |
Install the camshaft timing pulley.
Fasten the bolt of the camshaft timing pulley by holding the camshaft with a wrench.
| 39. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY |
Remove any old seal packing (FIPG) material from the cylinder head.
![]() |
Apply seal packing to the specific areas shown in the illustration.
Install a new cylinder head cover gasket and the cylinder head cover with the 10 bolts and 2 nuts.
Install 4 new nozzle holder seals.
Connect the ventilation hose.
Connect the 4 connectors and install the 3 bolts.
| 40. INSTALL NOZZLE HOLDER SEAL |
Install 4 new nozzle holder seals.
| 41. INSTALL OIL FILLER CAP SUB-ASSEMBLY |