ENGINE OIL COOLER (w/o EGR Cooler) > REMOVAL |
| 1. REMOVE NO. 1 ENGINE UNDER COVER (for 4WD) |
Remove the 4 bolts and under cover.
| 2. REMOVE NO. 2 ENGINE UNDER COVER (for 4WD) |
Remove the 2 bolts and under cover.
| 3. DRAIN ENGINE OIL |
Remove the oil filter cap.
Remove the oil drain plug, and drain the engine oil from the oil pan.
| 4. LOOSEN FUEL TANK CAP ASSEMBLY |
| 5. DRAIN FUEL |
| 6. REMOVE MANIFOLD STAY |
![]() |
Remove the 2 bolts and stay.
| 7. REMOVE OIL LEVEL GAUGE SUB-ASSEMBLY |
Remove the bolt and gauge.
Remove the O-ring from the gauge.
| 8. REMOVE FUEL INLET PIPE SUB-ASSEMBLY |
Remove the engine oil level dipstick.
![]() |
Remove the bolt and clamp.
Remove the bolt and engine oil level dipstick guide.
Remove the O-ring engine oil level dipstick guide.
![]() |
Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.
| 9. REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE |
![]() |
Remove the bolt and No. 2 injection pipe clamp.
Remove the 2 nuts and No. 3 injection pipe clamp.
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
| 10. REMOVE NO. 4 INJECTION PIPE |
![]() |
Remove the 2 bolts and disconnect the 2 injection pipe clamps.
![]() |
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
| 11. REMOVE OIL FILTER SUB-ASSEMBLY |
![]() |
Using SST, remove the oil filter.
| 12. REMOVE STARTER ASSEMBLY |
for A340F A340E:
Remove transmission oil filler tube sub-assembly.
Remove the oil level dipstick.
Remove the 2 bolts and transmission oil filler tube sub-assembly.
Remove the O-ring from the transmission oil filler tube sub-assembly.
![]() |
Disconnect the starter connector.
Remove the nut and disconnect the starter wire.
![]() |
A/T:
Remove the 2 nuts, bolt, and disconnect the ground cable.
![]() |
M/T:
Remove the nut, bolt, and disconnect the ground cable.
Remove the starter.
| 13. REMOVE FUEL SUPPLY PUMP ASSEMBLY |
![]() |
Remove the bolt and clamp.
Remove the 2 bolts and oil level gauge guide.
![]() |
Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.
![]() |
Disconnect the 2 fuel hoses.
![]() |
Disconnect the 2 connectors.
![]() |
Remove the 4 bolts indicated by the arrows in the illustration.
Remove the No. 2 camshaft timing pulley flange and pump drive shaft pulley.
![]() |
Remove the set nut and O-ring while holding the crankshaft pulley by using SST.
![]() |
Loosen the 2 nuts.
![]() |
Using SST, disconnect the pump from the injection gear.
Remove the 2 nuts and pump.
Remove the O-ring.
| 14. REMOVE COMMON RAIL ASSEMBLY |
Disconnect the 2 connectors.
![]() |
Remove the 2 bolts, common rail and No. 2 intake manifold insulator.
| 15. REMOVE OIL COOLER COVER SUB-ASSEMBLY |
![]() |
Disconnect the oil pressure switch connector and wire harness.
Remove the 13 bolts, 2 nuts and oil cooler cover.
| 16. REMOVE OIL COOLER ASSEMBLY |
Loosen the 4 nuts first.
Partially tap out the oil cooler by tapping each nut head with a plastic-faced hammer.
Remove the 4 nuts, oil cooler and 2 gaskets.