INTAKE AIR CONTROL SYSTEM (w/o EGR Cooler) > ON-VEHICLE INSPECTION |
| 1. CHECK INTAKE AIR SYSTEM |
Check for leakage or clogging between the air cleaner housing and turbocharger inlet, and between the turbocharger outlet and cylinder head.
| Condition | Operation |
| Clogged air cleaner | Clean or replace |
| Collapsed or deformed hoses | Repair or replace |
| Leakage from connections | Check each connection and repair |
| Cracks in components | Check and replace |
| 2. CHECK EXHAUST SYSTEM |
Check for leakage or clogging between the cylinder head and turbocharger inlet, and between the turbocharger outlet and exhaust pipe.
| Condition | Operation |
| Deformed components | Repair or replace |
| Foreign matter in passages | Remove |
| Leakage from components | Repair or replace |
| Cracks in components | Check or replace |
| 3. CHECK BOOST PRESSURE |
Warm up the engine.
![]() |
Using a 3-way connector, connect SST (turbocharger pressure gauge) to the hose between the manifold absolute pressure sensor and the gas filter leading to the intake air connector.
Fully apply the parking brake and chock the 4 wheels.
for Manual Transmission:
While depressing the clutch pedal, fully depress the accelerator pedal. Measure the boost pressure at maximum engine speed (approximately 4600 rpm).
for Automatic Transmission:
Move the shift lever to P or N, and then fully depress the accelerator pedal. Measure the boost pressure at maximum engine speed (approximately 4600 rpm).
Chart showing the suspected trouble areas when the pressure is lower than the standard.
| Item | MAP (Absolute pressure inside intake manifold) | MAF (Intake air flow rate) | Accel Position | Actual Throttle Position | Actual EGR Valve Position | EGR Close Lrn. Status (EGR valve fully closed position learning status) | Fuel Pressure | Injection Feedback Val #1 (to #4) |
| Values taken from an actual normal vehicle *1 | - | 96 g/sec. | 99% or more | None | None | OK | - | -3 to +3 mm3/st |
| Values which represent a malfunction *1 | None | MAF is less than 81 g/sec. | Accel Position is not fully depressed position *2 | None | None *3 | NG NG (Determined after performing learning) *3 | Fuel Pressure is lower than Target Common Rail Pressure by 10 MPa or more (Check while steady condition) | Outside of above range |
| Turbocharger | ○ | ○ | - | - | - | - | - | - |
| EGR valve does not close or has problem with movement | ○ | ○ | - | - | ○ (Problem with EGR valve movement) *4 | ○ (EGR valve does not close) *4 | - | - |
| Problem with diesel throttle movement | ○ (Intake airflow decreases) | ○ | - | ○ | - | - | - | - |
| Accelerator pedal cannot be fully depressed or problem with accelerator pedal position sensor exists | - | ○ | ○ | - | - | - | - | - |
| Intake air system leakage or blockage | ○ | ○ | - | - | - | - | - | - |
| Exhaust gas leakage before turbocharger or blockage | ○ | ○ | - | - | - | - | - | - |
| Manifold absolute pressure sensor | ○ | ○ | - | - | - | - | - | - |
| Manifold absolute pressure sensor hose is disconnected | ○ | ○ | - | - | - | - | - | - |
| Mass air flow meter sub-assembly | - | ○ | - | - | - | - | - | - |
| Fuel system (injector, supply pump or common rail) | ○ | ○ | - | - | - | - | ○ (Fuel injector leakage, decrease in pressure discharge valve relief pressure or valve is stuck) | ○ *5 |
| 4. CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR |
![]() |
Inspect the power source voltage.
Disconnect the pressure sensor connector.
Turn the ignition switch ON.
Measure the voltage between terminals T9-3 (VC (+)) and T9-1 (E2 (-)) of the wire harness side connector.
Turn the ignition switch OFF.
Connect the pressure sensor connector.
![]() |
Check the power supply.
Turn the ignition switch ON.
Disconnect the vacuum hose from the pressure sensor.
Connect a voltmeter to terminals E7-28 (PIM (+)) and E8-28 (E2 (-)) of the ECM, and measure the output voltage at ambient atmospheric pressure.
![]() |
Apply a vacuum to the pressure sensor in 13.3 kPa (100 mmHg, 3.94 in.Hg) increments until the pressure reaches 40.0 kPa (300 mmHg, 11.81 in.Hg). Measure the decrease in voltage for each increment.
| Applied Vacuum | Voltage Decrease |
| -13.3 kPa (100 mmHg, 3.94 in.Hg) | 0.1 to 0.4 V |
| -26.6 kPa (199 mmHg, 7.85 in.Hg) | 0.2 to 0.6 V |
| -40 kPa (300 mmHg, 11.81 in.Hg) | 0.4 to 0.8 V |
![]() |
Using SST (turbocharger pressure gauge), apply pressure to the pressure sensor in 19.6 kPa (0.20 kgf*cm2, 2.84 psi) increments until the pressure reaches 98.0 kPa (1.00 kgf*cm2, 14.2 psi). Measure the increase in voltage for each increment.
| Applied Pressure | Voltage Increase |
| 19.6 kPa (0.20 kgf*cm2, 2.84 psi) | 0.1 to 0.4 V |
| 39.2 kPa (0.40 kgf*cm2, 5.69 psi) | 0.4 to 0.7 V |
| 58.8 kPa (0.60 kgf*cm2, 8.53 psi) | 0.7 to 1.0 V |
| 78.5 kPa (0.80 kgf*cm2, 11.4 psi) | 1.0 to 1.3 V |
| 98.0 kPa (1.00 kgf*cm2, 14.2 psi) | 1.3 to 1.6 V |