Home › BODY › MIRROR › POWER MIRROR CONTROL SYSTEM

POWER MIRROR CONTROL SYSTEM > INSPECTION

for Preparation Click here



1. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Retract Mirror)


B203252E03
  1. Inspect the outer mirror switch.

    1. Select "L" on the left/right adjustment switch.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      4 (MLV) - 8 (B)
      6 (M+) - 7 (E)
      UP
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      4 (MLV) - 7 (E)
      6 (M+) - 8 (B)
      DOWN
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      5 (MLH) - 8 (B)
      6 (M+) - 7 (E)
      LEFT
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      5 (MLH) - 7 (E)
      6 (M+) - 8 (B)
      RIGHT
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher

      If the result is not as specified, replace the outer mirror switch.

    3. Select "R" on the left/right adjustment switch.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      3 (MRV) - 8 (B)
      6 (M+) - 7 (E)
      UP
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      3 (MRV) - 7 (E)
      6 (M+) - 8 (B)
      DOWN
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      2 (MRH) - 8 (B)
      6 (M+) - 7 (E)
      LEFT
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      2 (MRH) - 7 (E)
      6 (M+) - 8 (B)
      RIGHT
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher

      If the result is not as specified, replace the outer mirror switch.



2. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Retract Mirror)


B207176E02
  1. Inspect the outer mirror switch.

    1. Select "L" on the left/right adjustment switch.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      4 (MLV) - 8 (B)
      6 (M+) - 7 (E)
      UP
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      4 (MLV) - 7 (E)
      6 (M+) - 8 (B)
      DOWN
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      5 (MLH) - 8 (B)
      6 (M+) - 7 (E)
      LEFT
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      5 (MLH) - 7 (E)
      6 (M+) - 8 (B)
      RIGHT
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher

      If the result is not as specified, replace the outer mirror switch.

    3. Select "R" on the left/right adjustment switch.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      3 (MRV) - 8 (B)
      6 (M+) - 7 (E)
      UP
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      3 (MRV) - 7 (E)
      6 (M+) - 8 (B)
      DOWN
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      2 (MRH) - 8 (B)
      6 (M+) - 7 (E)
      LEFT
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      2 (MRH) - 7 (E)
      6 (M+) - 8 (B)
      RIGHT
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher

      If the result is not as specified, replace the outer mirror switch.

  1. Inspect the retract switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      7 (E) - 10 (MF)
      8 (B) - 9 (MR)
      Pushed in
      Below 1 Ω
      7 (E) - 9 (MR)
      8 (B) - 10 (MF)
      Not pushed in
      Below 1 Ω

      If the result is not as specified, replace the outer mirror switch.



3. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH


B085125E02
  1. Disconnect the mirror connector.

  1. Apply battery voltage and check operation of the mirror.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) →Terminal 5 (MV)
    Battery negative (-) → Terminal 3 (M+)
    Turns upward (A)
    Battery positive (+) → Terminal 3 (M+)
    Battery negative (-) → Terminal 5 (MV)
    Turns downward (B)
    Battery positive (+) → Terminal 1 (MH)
    Battery negative (-) → Terminal 3 (M+)
    Turns left (C)
    Battery positive (+) → Terminal 3 (M+)
    Battery negative (-) → Terminal 1 (MH)
    Turns right (D)

    If the result is not as specified, replace the mirror assembly.



    B203272E01
  1. w/ Retract Mirror:

    1. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

      OK:
      Measurement Condition
      Mirror Position
      Specified Condition
      Battery positive (+) → Terminal 6 (MR)
      Battery negative (-) → Terminal 4 (MF)
      Forward position (A)
      Moves from (A) to retracted position (E)
      Battery negative (-) → Terminal 6 (MR)
      Battery positive (+) → Terminal 4 (MF)
      Forward position (A)
      Does not move
      Battery positive (+) → Terminal 6 (MR)
      Battery negative (-) → Terminal 4 (MF)
      Position between forward position (A) and driving position (C)
      Moves from (B) to retracted position (E)
      Battery negative (-) → Terminal 6 (MR)
      Battery positive (+) → Terminal 4 (MF)
      Position between forward position (A) and driving position (C)
      Moves from (B) to retracted position (A)
      Battery positive (+) → Terminal 6 (MR)
      Battery negative (-) → Terminal 4 (MF)
      Driving position (C)
      Moves from (C) to retracted position (E)
      Battery negative (-) → Terminal 6 (MR)
      Battery positive (+) → Terminal 4 (MF)
      Driving position (C)
      Does not move
      Battery positive (+) → Terminal 6 (MR)
      Battery negative (-) → Terminal 4 (MF)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to retracted position (E)
      Battery negative (-) → Terminal 6 (MR)
      Battery positive (+) → Terminal 4 (MF)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to retracted position (C)
      Battery positive (+) → Terminal 6 (MR)
      Battery negative (-) → Terminal 4 (MF)
      Retracted position (E)
      Does not move
      Battery negative (-) → Terminal 6 (MR)
      Battery positive (+) → Terminal 4 (MF)
      Retracted position (E)
      Moves from (E) to driving position (C)

      NOTICE:
      1. Disconnect and reconnect the battery between each mirror position check.
      2. Do not apply battery voltage when moving the mirror by hand into each mirror position.

      If the result is not as specified, replace the mirror assembly.



4. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH


B085124E03
  1. Disconnect the mirror connector.

  1. Apply battery voltage and check operation of the mirror.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) →Terminal 5 (MV)
    Battery negative (-) → Terminal 3 (M+)
    Turns upward (A)
    Battery positive (+) → Terminal 3 (M+)
    Battery negative (-) → Terminal 5 (MV)
    Turns downward (B)
    Battery positive (+) → Terminal 1 (MH)
    Battery negative (-) → Terminal 3 (M+)
    Turns left (C)
    Battery positive (+) → Terminal 3 (M+)
    Battery negative (-) → Terminal 1 (MH)
    Turns right (D)

    If the result is not as specified, replace the mirror assembly.



    B203273E01
  1. w/ Retract Mirror:

    1. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

      OK:
      Measurement Condition
      Mirror Position
      Specified Condition
      Battery positive (+) → Terminal 6 (MR)
      Battery negative (-) → Terminal 4 (MF)
      Forward position (A)
      Moves from (A) to retracted position (E)
      Battery negative (-) → Terminal 6 (MR)
      Battery positive (+) → Terminal 4 (MF)
      Forward position (A)
      Does not move
      Battery positive (+) → Terminal 6 (MR)
      Battery negative (-) → Terminal 4 (MF)
      Position between forward position (A) and driving position (C)
      Moves from (B) to retracted position (E)
      Battery negative (-) → Terminal 6 (MR)
      Battery positive (+) → Terminal 4 (MF)
      Position between forward position (A) and driving position (C)
      Moves from (B) to retracted position (A)
      Battery positive (+) → Terminal 6 (MR)
      Battery negative (-) → Terminal 4 (MF)
      Driving position (C)
      Moves from (C) to retracted position (E)
      Battery negative (-) → Terminal 6 (MR)
      Battery positive (+) → Terminal 4 (MF)
      Driving position (C)
      Does not move
      Battery positive (+) → Terminal 6 (MR)
      Battery negative (-) → Terminal 4 (MF)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to retracted position (E)
      Battery negative (-) → Terminal 6 (MR)
      Battery positive (+) → Terminal 4 (MF)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to retracted position (C)
      Battery positive (+) → Terminal 6 (MR)
      Battery negative (-) → Terminal 4 (MF)
      Retracted position (E)
      Does not move
      Battery negative (-) → Terminal 6 (MR)
      Battery positive (+) → Terminal 4 (MF)
      Retracted position (E)
      Moves from (E) to driving position (C)

      NOTICE:
      1. Disconnect and reconnect the battery between each mirror position check.
      2. Do not apply battery voltage when moving the mirror by hand into each mirror position.

      If the result is not as specified, replace the mirror assembly.