POWER MIRROR CONTROL SYSTEM > INSPECTION |
| 1. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Retract Mirror) |
![]() |
Inspect the outer mirror switch.
Select "L" on the left/right adjustment switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | |
| 4 (MLV) - 8 (B) 6 (M+) - 7 (E) | UP | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
| 4 (MLV) - 7 (E) 6 (M+) - 8 (B) | DOWN | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
| 5 (MLH) - 8 (B) 6 (M+) - 7 (E) | LEFT | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
| 5 (MLH) - 7 (E) 6 (M+) - 8 (B) | RIGHT | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
Select "R" on the left/right adjustment switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | |
| 3 (MRV) - 8 (B) 6 (M+) - 7 (E) | UP | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
| 3 (MRV) - 7 (E) 6 (M+) - 8 (B) | DOWN | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
| 2 (MRH) - 8 (B) 6 (M+) - 7 (E) | LEFT | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
| 2 (MRH) - 7 (E) 6 (M+) - 8 (B) | RIGHT | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
| 2. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Retract Mirror) |
![]() |
Inspect the outer mirror switch.
Select "L" on the left/right adjustment switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | |
| 4 (MLV) - 8 (B) 6 (M+) - 7 (E) | UP | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
| 4 (MLV) - 7 (E) 6 (M+) - 8 (B) | DOWN | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
| 5 (MLH) - 8 (B) 6 (M+) - 7 (E) | LEFT | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
| 5 (MLH) - 7 (E) 6 (M+) - 8 (B) | RIGHT | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
Select "R" on the left/right adjustment switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | |
| 3 (MRV) - 8 (B) 6 (M+) - 7 (E) | UP | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
| 3 (MRV) - 7 (E) 6 (M+) - 8 (B) | DOWN | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
| 2 (MRH) - 8 (B) 6 (M+) - 7 (E) | LEFT | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
| 2 (MRH) - 7 (E) 6 (M+) - 8 (B) | RIGHT | Pressed | Below 1 Ω |
| Not pressed | 10 kΩ or higher | ||
Inspect the retract switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 7 (E) - 10 (MF) 8 (B) - 9 (MR) | Pushed in | Below 1 Ω |
| 7 (E) - 9 (MR) 8 (B) - 10 (MF) | Not pushed in | Below 1 Ω |
| 3. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH |
![]() |
Disconnect the mirror connector.
Apply battery voltage and check operation of the mirror.
| Measurement Condition | Specified Condition |
| Battery positive (+) →Terminal 9 (MV) Battery negative (-) → Terminal 8 (M+) | Turns upward (A) |
| Battery positive (+) → Terminal 8 (M+) Battery negative (-) → Terminal 9 (MV) | Turns downward (B) |
| Battery positive (+) → Terminal 4 (MH) Battery negative (-) → Terminal 8 (M+) | Turns left (C) |
| Battery positive (+) → Terminal 8 (M+) Battery negative (-) → Terminal 4 (MH) | Turns right (D) |
![]() |
w/ Retract Mirror:
For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.
| Measurement Condition | Mirror Position | Specified Condition |
| Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 2 (MF) | Forward position (A) | Moves from (A) to retracted position (E) |
| Battery negative (-) → Terminal 7 (MR) Battery positive (+) → Terminal 2 (MF) | Forward position (A) | Does not move |
| Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 2 (MF) | Position between forward position (A) and driving position (C) | Moves from (B) to retracted position (E) |
| Battery negative (-) → Terminal 7 (MR) Battery positive (+) → Terminal 2 (MF) | Position between forward position (A) and driving position (C) | Moves from (B) to retracted position (A) |
| Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 2 (MF) | Driving position (C) | Moves from (C) to retracted position (E) |
| Battery negative (-) → Terminal 7 (MR) Battery positive (+) → Terminal 2 (MF) | Driving position (C) | Does not move |
| Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 2 (MF) | Position between driving position (C) and retracted position (E) | Moves from (D) to retracted position (E) |
| Battery negative (-) → Terminal 7 (MR) Battery positive (+) → Terminal 2 (MF) | Position between driving position (C) and retracted position (E) | Moves from (D) to retracted position (C) |
| Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 2 (MF) | Retracted position (E) | Does not move |
| Battery negative (-) → Terminal 7 (MR) Battery positive (+) → Terminal 2 (MF) | Retracted position (E) | Moves from (E) to driving position (C) |
| 4. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH |
![]() |
Disconnect the mirror connector.
Apply battery voltage and check operation of the mirror.
| Measurement Condition | Specified Condition |
| Battery positive (+) →Terminal 9 (MV) Battery negative (-) → Terminal 8 (M+) | Turns upward (A) |
| Battery positive (+) → Terminal 8 (M+) Battery negative (-) → Terminal 9 (MV) | Turns downward (B) |
| Battery positive (+) → Terminal 4 (MH) Battery negative (-) → Terminal 8 (M+) | Turns left (C) |
| Battery positive (+) → Terminal 8 (M+) Battery negative (-) → Terminal 4 (MH) | Turns right (D) |
![]() |
w/ Retract Mirror:
For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.
| Measurement Condition | Mirror Position | Specified Condition |
| Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 2 (MF) | Forward position (A) | Moves from (A) to retracted position (E) |
| Battery negative (-) → Terminal 7 (MR) Battery positive (+) → Terminal 2 (MF) | Forward position (A) | Does not move |
| Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 2 (MF) | Position between forward position (A) and driving position (C) | Moves from (B) to retracted position (E) |
| Battery negative (-) → Terminal 7 (MR) Battery positive (+) → Terminal 2 (MF) | Position between forward position (A) and driving position (C) | Moves from (B) to retracted position (A) |
| Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 2 (MF) | Driving position (C) | Moves from (C) to retracted position (E) |
| Battery negative (-) → Terminal 7 (MR) Battery positive (+) → Terminal 2 (MF) | Driving position (C) | Does not move |
| Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 2 (MF) | Position between driving position (C) and retracted position (E) | Moves from (D) to retracted position (E) |
| Battery negative (-) → Terminal 7 (MR) Battery positive (+) → Terminal 2 (MF) | Position between driving position (C) and retracted position (E) | Moves from (D) to retracted position (C) |
| Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 2 (MF) | Retracted position (E) | Does not move |
| Battery negative (-) → Terminal 7 (MR) Battery positive (+) → Terminal 2 (MF) | Retracted position (E) | Moves from (E) to driving position (C) |