Home › ENGINE · 2KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (w/o EGR Cooler)

DTC    P0405/96    Exhaust Gas Recirculation Sensor "A" Circuit Low

DTC    P0406/96    Exhaust Gas Recirculation Sensor "A" Circuit High

for Preparation Click here


DESCRIPTION

The EGR valve position sensor is mounted on the EGR valve and used for detecting the lift amount of the valve. The lift amount detected by the sensor is provided to the ECM as feedback, and then the ECM regulates the lift amount of the valve in accordance with the engine running condition.

DTC No.
DTC Detection Condition
Trouble Area
P0405/96
EGR valve position sensor output voltage is less than 0.1 V for more than 5 seconds
(1 trip detection logic)
  1. Open or short in EGR valve position sensor circuit
  2. EGR valve position sensor
  3. ECM
P0406/96
EGR valve position sensor output voltage is more than 4.9 V for more than 5 seconds
(1 trip detection logic)
  1. Open or short in EGR valve position sensor circuit
  2. EGR valve position sensor
  3. ECM

HINT:
  1. After confirming DTCs P0405/96 and P0406/96, check the EGR valve opening angle condition.

    Result
    Condition
    Changes between 0.3 to 4.2 V
    Normal
    Less than 0.1 V
    P0405/96 (Low input voltage)
    More than 4.9 V
    P0406/96 (High input voltage)
  2. The result values above are for when the ignition switch is ON (engine is stopped), or when the engine is fully warmed-up and idling.


MONITOR DESCRIPTION

G039134E04
When the output voltage of the EGR valve position sensor deviates from the normal operating range of 0.1 to 4.9 V for more than 0.5 seconds, the ECM interprets this as a malfunction of the sensor circuit, and illuminates the MIL.

WIRING DIAGRAM


A119976E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.

NOTICE:
If the ECM is replaced, the new ECM needs initialization (Click here).

1.CHECK ECM (VC VOLTAGE)
A085350E04
  1. Disconnect the E2 EGR valve position sensor connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    E2-1 (VC) - E2-2 (E2)
    4.5 to 5.5 V



NG
Go to step 3
OK


2.INSPECT EGR VALVE POSITION SENSOR (RESISTANCE)


NG
REPLACE EGR VALVE POSITION SENSOR
OK


3.CHECK WIRE HARNESS (EGR VALVE POSITION SENSOR - ECM)
G034912E04
  1. Disconnect the E2 sensor connector.

  1. Disconnect the E7 and E8 ECM connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    E2-3 (EGLS) - E7-33 (EGLS)
    Below 1 Ω
    E2-2 (E2) - E8-28 (E2)
    Below 1 Ω
    E2-3 (EGLS) or E7-33 (EGLS) - Body ground
    10 kΩ or higher
    E2-2 (E2) or E8-28 (E2) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM