AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) > Compressor Circuit |


| 1.READ VALUE USING INTELLIGENT TESTER (A/C Signal) |
Use the Data List to check if the A/C system is functioning properly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| A/C Signal | A/C signal / ON or OFF | ON: A/C ON OFF: A/C OFF | - |
|
| ||||
| OK | |
| 2.INSPECT MAGNET CLUTCH RELAY |
![]() |
Remove the magnet clutch relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | Battery voltage is not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage is applied to terminals 1 and 2 | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY) |
![]() |
Disconnect the A37 amplifier connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A37-13 (MGC) - Body ground | Ignition switch ON | 11 to 14 V |
|
| ||||
| OK | |
| 4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (MGC VOLTAGE) |
![]() |
Remove the air conditioning amplifier with its connectors still connected.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A37-13 (MGC) - Body ground | Ignition switch START A/C switch ON | Below 1 V |
| Ignition switch START A/C switch OFF | 11 to 14 V |
|
| ||||
| OK | |
| 5.INSPECT COOLER COMPRESSOR ASSEMBLY (MAGNET CLUTCH ASSEMBLY) |
![]() |
Disconnect the clutch connector.
Apply battery voltage to the clutch and check operation of the clutch.
| Measurement Connection | Specified Condition |
| Battery positive (+) → Terminal 1 Battery negative (-) → Ground wire | Magnet clutch engages |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (COOLER COMPRESSOR ASSEMBLY - MAGNET CLUTCH RELAY) |
![]() |
Disconnect the A1 compressor connector.
Remove the magnet clutch relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A1-1 - M2-3 | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ECM) |
![]() |
Disconnect the A37 amplifier connector.
Disconnect the E6*1, E13*2 or E10*3 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A37-21 (AC1) - E6-18 (AC1) | Always | Below 1 Ω |
| A37-7 (ACT) - E6-19 (ACT) |
| Tester Connection | Condition | Specified Condition |
| A37-21 (AC1) - E13-24 (AC1) | Always | Below 1 Ω |
| A37-7 (ACT) - E13-25 (ACT) |
| Tester Connection | Condition | Specified Condition |
| A37-21 (AC1) - E10-24 (AC1) | Always | Below 1 Ω |
| A37-7 (ACT) - E10-25 (ACT) |
|
| ||||
| OK | |
| 8.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (AC1 VOLTAGE) |
![]() |
Remove the air conditioning amplifier with its connectors still connected.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A37-21 (AC1) - Body ground | Ignition switch START A/C switch AUTO Magnet clutch is engaged | Below 1 V |
| Ignition switch START A/C switch AUTO Magnet clutch is not engaged | 11 to 14 V |
|
| ||||
| OK | |
| 9.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (ACT VOLTAGE) |
![]() |
Remove the air conditioning amplifier with its connectors still connected.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A37-7 (ACT) - Body ground | Ignition switch START A/C switch AUTO | 11 to 14 V |
|
| ||||
| OK | ||
| ||