Home › SECURITIES › THEFT DETERRENT › THEFT DETERRENT SYSTEM

THEFT DETERRENT SYSTEM > TERMINALS OF ECU



CHECK THEFT WARNING ECU ASSEMBLY

B119765E01

  1. Disconnect the T16 ECU connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    IG (T16-4) - E (T16-1)
    R-L - W-B
    Ignition power supply
    Ignition switch OFF
    Below 1 V
    IG (T16-4) - E (T16-1)
    R-L - W-B
    Ignition power supply
    Ignition switch ON
    10 to 14 V
    +B1 (T16-3) - E (T16-1)
    L-Y - W-B
    +B (ECU-B) power source
    Always
    10 to 14 V
    +B2 (T16-12) - E (T16-1)
    LG - W-B
    +B (DOOR) power source
    Always
    10 to 14 V
    DSWH (T16-9) - E (T16-1)
    G-R - W-B
    Security courtesy switch input
    Engine hood fully closed
    10 kΩ or higher
    DSWH (T16-9) - E (T16-1)
    G-R - W-B
    Security courtesy switch input
    Engine hood open
    Below 1 Ω
    E (T16-1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    L2 (T16-20) - Body ground
    L - Body ground
    Door control switch (master switch) lock output
    Door control switch (master switch) LOCK
    Below 1 Ω
    L2 (T16-20) - Body ground
    L - Body ground
    Door control switch (master switch) lock output
    Door control switch (master switch) OFF
    10 kΩ or higher
    UL3 (T16-21) - Body ground
    L-W - Body ground
    Door control switch (master switch) unlock output
    Door control switch (master switch) UNLOCK
    Below 1 Ω
    UL3 (T16-21) - Body ground
    L-W - Body ground
    Door control switch (master switch) unlock output
    Door control switch (master switch) OFF
    10 kΩ or higher
    KSW (T16-5) - Body ground
    G-Y - Body ground
    Unlock warning switch
    No key in ignition key cylinder
    10 kΩ or higher
    KSW (T16-5) - Body ground
    G-Y - Body ground
    Unlock warning switch
    Key inserted in ignition key cylinder
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the T16 ECU connector.



  4. Measure the voltage of the connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    IND (T16-22) - E (T16-1)
    G-R - W-B
    Security indicator light signal output
    Security indicator light is flashing
    (theft deterrent system is operating)
    Alternating between
    below 1 V and 10 to 14 V
    CTY (T16-7) - E (T16-1)
    R-L - W-B
    All courtesy switch signals input
    Driver side, front passenger side, rear RH or rear LH door closed
    10 to 14 V
    CTY (T16-7) - E (T16-1)
    R-L - W-B
    All courtesy switch signals input
    Driver side, front passenger side, rear RH or rear LH door open
    Below 1 V
    HORN (T16-24) - E (T16-1)
    W-R - W-B
    Both vehicle horn signals output
    (low pitched and high pitched)
    Armed state
    10 to 14 V
    HORN (T16-24) - E (T16-1)
    W-R - W-B
    Vehicle horn signal output
    Alarm sounding state
    Below 1 V
    SH- (T16-26) - E (T16-1)
    B - W-B
    Security horn signal output
    Security horn is sounding
    (theft deterrent system is in alarm sounding state)
    Alternating between below 1 V and 10 to 14 V
    HAZD (T16-23) - E (T16-1)
    G-O - W-B
    All hazard warning light signals output
    Hazard warning lights are flashing
    (theft deterrent system is in alarm sounding state)
    Alternating between below 1 V and 10 to 14 V
    SPD (T16-15) - E (T16-1)
    V-R - W-B
    Speed signal from combination meter
    Ignition switch ON, one driving wheel is rotating slowly
    Pulse generation
    (see waveform)

    1. If the result is not as specified, the ECU may have a malfunction.



      B119732E01
    1. Waveform
      Vehicle speed signal
      Item
      Content
      Symbols (Terminal No.)
      SPD (T16-15) - E (T16-1)
      Tool Setting
      5 V/DIV., 20 msec./DIV.
      Condition
      While driving vehicle

      HINT:
      The wavelength becomes shorter as the vehicle speed increases.


CHECK INSTRUMENT PANEL JUNCTION BLOCK (INTEGRATION RELAY)

B119772E01

  1. Disconnect the 2A, 2D and 2L junction block connectors.

  2. Measure the voltage and resistance of the wire harness side connectors.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    BECU (2L-12) - GND (2D-9)
    L - W-B
    +B (BECU) power source
    Always
    10 to 14 V
    GND (2D-9, 18) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    L1 (2A-4) - Body ground
    L - Body ground
    Door control switch (master switch) lock input
    Door control switch (master switch) LOCK
    10 kΩ or higher
    L1 (2A-4) - Body ground
    L - Body ground
    Door control switch (master switch) lock input
    Door control switch (master switch) OFF
    Below 1 Ω
    UL1 (2D-4) - Body ground
    L-W - Body ground
    Door control switch (master switch) unlock input
    Door control switch (master switch) UNLOCK
    10 kΩ or higher
    UL1 (2D-4) - Body ground
    L-W - Body ground
    Door control switch (master switch) unlock input
    Door control switch (master switch) OFF
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the 2A, 2D and 2L junction block connectors.

  4. Measure the voltage of the wire harness side connectors.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    ACT+ (2R-28) - Body ground
    L - Body ground
    Door lock motor LOCK drive output (driver side door)
    Door control switch (master switch) or driver side door key cylinder OFF
    Below 1 V
    ACT+ (2R-28) - Body ground
    L - Body ground
    Door lock motor LOCK drive output (driver side door)
    Door control switch (master switch) or driver side door key cylinder LOCK
    10 to 14 V
    ACT- (2R-27) - Body ground
    L-Y - Body ground
    Door lock motor UNLOCK drive output (driver side door)
    Door control switch (master switch) or driver side door key cylinder OFF
    Below 1 V
    ACT- (2R-27) - Body ground
    L-Y - Body ground
    Door lock motor UNLOCK drive output (driver side door)
    Door control switch (master switch) or driver side door key cylinder UNLOCK
    10 to 14 V
    DCTY (2O-27) - Body ground
    R-B - Body ground
    Driver side courtesy switch input
    Driver side door closed
    10 to 14 V
    DCTY (2O-27) - Body ground
    R-B - Body ground
    Driver side courtesy switch input
    Driver side door open
    Below 1 V

    1. If the result is not as specified, there may be a malfunction on the junction block (relay).