Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1900/73    Short in Front Driver Side Pretensioner Squib Circuit

DTC    B1901/73    Open in Front Driver Side Pretensioner Squib Circuit

DTC    B1902/73    Short to GND in Front Driver Side Pretensioner Squib Circuit

DTC    B1903/73    Short to B+ in Front Driver Side Pretensioner Squib Circuit

for Preparation Click here


DESCRIPTION

The driver side front pretensioner squib circuit consists of the center airbag sensor and the front seat outer belt driver side. The circuit instructs the SRS to deploy when deployment conditions are met. These DTCs are recorded when a malfunction is detected in the driver side front pretensioner squib circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1900/73
When one of following conditions is met:
  1. Center airbag sensor assembly receives line short circuit signal 5 times in driver side front pretensioner squib circuit during primary check
  2. Front pretensioner squib driver side malfunction
  3. Center airbag sensor assembly malfunction
  1. Front seat outer belt assembly driver side (driver side front pretensioner squib)
  2. Center airbag sensor assembly
  3. Floor wire
B1901/73
When one of following conditions is met:
  1. Center airbag sensor assembly receives open circuit signal in driver side front pretensioner squib circuit for 2 seconds
  2. Front pretensioner squib driver side malfunction
  3. Center airbag sensor assembly malfunction
  1. Front seat outer belt assembly driver side (driver side front pretensioner squib)
  2. Center airbag sensor assembly
  3. Floor wire
B1902/73
When one of following conditions is met:
  1. Center airbag sensor assembly receives short circuit to ground signal in driver side front pretensioner squib circuit for 0.5 seconds
  2. Front pretensioner squib driver side malfunction
  3. Center airbag sensor assembly malfunction
  1. Front seat outer belt assembly driver side (driver side front pretensioner squib)
  2. Center airbag sensor assembly
  3. Floor wire
B1903/73
When one of following conditions is met:
  1. Center airbag sensor assembly receives short circuit to B+ signal in driver side front pretensioner squib circuit for 0.5 seconds
  2. Front pretensioner squib driver side malfunction
  3. Center airbag sensor assembly malfunction
  1. Front seat outer belt assembly driver side (driver side front pretensioner squib)
  2. Center airbag sensor assembly
  3. Floor wire

WIRING DIAGRAM


H101309E05


INSPECTION PROCEDURE

1.CHECK FRONT SEAT OUTER BELT ASSEMBLY DRIVER SIDE (DRIVER SIDE FRONT PRETENSIONER SQUIB)
H101446E06
  1. Turn the ignition switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connector from the front seat outer belt driver side.

  1. Connect the white wire side of SST (resistance 2.1 Ω) to the floor wire connector C.

SST
09843-18060  

CAUTION:
Never connect a tester to the driver side front pretensioner squib for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE:
  1. Do not forcibly insert SST into the terminals of the connector when connecting.
  2. Insert SST straight into the terminals of the connector.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1900, B1901, B1902, B1903 or 73 is not output.

    HINT:
    DTCs other than DTC B1900, B1901, B1902, B1903 or 73 may be output at this time, but they are not related to this check.



OK
REPLACE FRONT SEAT OUTER BELT ASSEMBLY DRIVER SIDE (DRIVER SIDE FRONT PRETENSIONER SQUIB)
NG


2.CHECK CONNECTOR
  1. Turn the ignition switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST (resistance 2.1 Ω) from the floor wire.

  1. Check that the floor wire connector (on the front seat outer belt driver side) is not damaged.

    OK:
    The lock button is not disengaged, or the claw of the lock is not deformed or damaged.



NG
REPAIR OR REPLACE FLOOR WIRE
OK


3.CHECK FLOOR WIRE
H100383E15
  1. Disconnect the connector from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    LHD
    Tester Connection
    Specified Condition
    F21-1 - Body ground
    Below 1 V
    F21-2 - Body ground
    Below 1 V
    RHD
    Tester Connection
    Specified Condition
    F22-1 - Body ground
    Below 1 V
    F22-2 - Body ground
    Below 1 V

  1. Turn the ignition switch OFF.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    LHD
    Tester Connection
    Specified Condition
    F21-1 - F21-2
    Below 1 Ω
    F21-1 - Body ground
    1 MΩ or higher
    F21-2 - Body ground
    1 MΩ or higher
    RHD
    Tester Connection
    Specified Condition
    F22-1 - F22-2
    Below 1 Ω
    F22-2 - Body ground
    1 MΩ or higher
    F22-1 - Body ground
    1 MΩ or higher

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    LHD
    Tester Connection
    Specified Condition
    F21-1 - F21-2
    1 MΩ or higher
    RHD
    Tester Connection
    Specified Condition
    F22-1 - F22-2
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY