Home › ENGINE · 5L-E › ENGINE CONTROL SYSTEM › ECD SYSTEM

DTC    14 (4)    Timing Control System Malfunction

for Preparation Click here


DESCRIPTION

The ECM controls the injection timing by actuating the timing control valve. The timing control valve is mounted on the injection pump and controls the pump internal fuel pressure through duty control.
The ECM detects the injection advance angle based on TDC and NE signals.

DTC No.
DTC Detection Condition
Trouble Area
14 (4)
During and after engine warm up, actual injection timing is different from target value of ECM calculated for several sec.
  1. Open or short in timing control valve circuit
  2. Timing control valve
  3. Fuel filter (Clogging)
  4. Fuel (Frozen, air present)
  5. Injection pump (Internal pressure and timing control valve)
  6. ECM

WIRING DIAGRAM


A119266E01


INSPECTION PROCEDURE

1.INSPECT TIMING CONTROL VALVE


    A105093E01
  1. Disconnect the timing control valve connector.

  1. Measure the resistance of the timing control valve.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    10 to 14 Ω



NG
REPLACE TIMING CONTROL VALVE
OK


2.CHECK ECM (TCV VOLTAGE)


    A062420E06
  1. Disconnect the E23 ECM connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    E23-11 (TCV) - Body ground
    9 to 14 V



NG
Go to step 6
OK


3.CHECK ECM (TCV VOLTAGE, SIGNAL)


    A106826E03
  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    E23-11 (TCV) - E23-14 (E1)
    9 to 14 V

  1. While idling, measure the waveform according to the value(s) in the table below.

    OK:
    Tester Connection
    Specified Condition
    E23-11 (TCV) - E23-14 (E1)
    Correct waveform is as shown



NG
REPLACE ECM
OK


4.CHECK FUEL FILTER
  1. Check the fuel filter (Click here).



NG
REPLACE FUEL FILTER
OK


5.CHECK FUEL LEAK
  1. Visually check the injection pump, each injector and fuel line for fuel leaks.

    OK:
    No leakage



NG
REPAIR OR REPLACE PART WITH FUEL LEAKAGE
OK

CHECK AND REPLACE INJECTION PUMP ASSEMBLY 

6.CHECK TIMING CONTROL VALVE (POWER SOURCE)


    A073804E03
  1. Disconnect the T29 timing control valve connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    T29-1 - Body ground
    9 to 14 V



OK
REPAIR OR REPLACE HARNESS AND CONNECTOR (TIMING CONTROL VALVE - ECM)
NG


7.CHECK WIRE HARNESS (ECM - INTEGRATION RELAY [MAIN RELAY])


    A106815E03
  1. Disconnect the T29 timing control valve connector.

  1. Disconnect the E23 ECM connector.

  1. Disconnect the 1J integration relay connector from the engine room junction block.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    T29-1 - 1J-5
    Below 1 Ω
    E23-11 (TCV) - Body ground
    10 kΩ or higher
    T29-1 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT