Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1620/21    Driver Side - Side Airbag Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The side airbag sensor (driver side) consists of the safing sensor, the diagnostic circuit, the lateral deceleration sensor, etc.
If the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether the SRS should be activated.
DTC B1620/21 is recorded when a malfunction is detected in the side airbag sensor (driver side) circuit.

DTC Code
Detection Condition
Trouble Area
B1620/21
When both conditions below are met:
  1. Driver side - side airbag sensor malfunction
  2. Center airbag sensor malfunction
  1. Side airbag sensor (driver side)
  2. Rear airbag sensor (driver side)
  3. Floor wire
  4. Center airbag sensor assembly

WIRING DIAGRAM


C194828E09


C194828E10


INSPECTION PROCEDURE

1.CHECK VEHICLE CONDITION
  1. Check vehicle condition.
    Result 
    Result
    Proceed to
    for LHD
    A
    for RHD
    B



A
Go to step 11
B


2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and side airbag sensor RH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


3.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and side airbag sensor RH.

  1. Check that the connectors (on the center airbag sensor side and side airbag sensor RH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


4.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - SIDE AIRBAG SENSOR RH)

C194788E02

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F24-3 (BBR-) - Body ground
    Ignition switch ON
    Below 1 V
    F24-4 (BBR+) - Body ground

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 8 (BBD+) and 15 (BBD-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F24-3 (BBR-) - F24-4 (BBR+)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F24-3 (BBR-) - F24-4 (BBR+)
    Always
    1 MΩ or higher
    F24-3 (BBR-) - Body ground
    F24-4 (BBR+) - Body ground



NG
REPLACE FLOOR WIRE
OK


5.CHECK SIDE AIRBAG SENSOR RH
C158841E08
  1. Interchange the side airbag sensor LH with RH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1620 and B1625 are not output
    A
    DTC B1620 is output
    B
    DTC B1625 is output
    C

    HINT:
    Codes other than DTC B1620 and B1625 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor LH and RH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK

B
REPLACE SIDE AIRBAG SENSOR RH
C


6.CHECK CONNECTION OF CONNECTORS
  1. Check that the connector is properly connected to the rear airbag sensor RH.

    OK:
    The connector is properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


7.CHECK CONNECTORS
  1. Disconnect the connectors from the side airbag sensor RH and rear airbag sensor RH.

  1. Check that the connector (on the rear airbag sensor RH side) is not damaged.

    OK:
    The connector is not deformed or damaged.



NG
REPLACE HARNESS AND CONNECTOR
OK


8.CHECK REAR AIRBAG SENSOR RH CIRCUIT

C194787E06

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    R13-2 (BCR+) - Body ground
    Ignition switch ON
    Below 1 V
    R13-1 (BCR-) - Body ground

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 1 (BCR+) and 2 (BCR-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    R13-2 (BCR+) - R13-1 (BCR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    R13-2 (BCR+) - R13-1 (BCR-)
    Always
    1 MΩ or higher
    R13-2 (BCR+) - Body ground
    R13-1 (BCR-) - Body ground



NG
REPLACE FLOOR WIRE
OK


9.CHECK FOR DTC


    C167367E04
  1. Connect the connectors to the side airbag sensor RH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1620 is output.

HINT:
Codes other than B1620 may be output at this time, but they are not related to this check.



NG
REPLACE REAR AIRBAG SENSOR RH
OK


10.CHECK SIDE AIRBAG SENSOR RH
C158841E08
  1. Interchange the side airbag sensor LH with RH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1620 and B1625 are not output
    A
    DTC B1620 is output
    B
    DTC B1625 is output
    C

    HINT:
    Codes other than DTC B1620 and B1625 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor LH and RH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK

B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
C

REPLACE SIDE AIRBAG SENSOR RH 

11.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and side airbag sensor LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


12.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and side airbag sensor LH.

  1. Check that the connectors (on the center airbag sensor side and side airbag sensor LH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


13.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - SIDE AIRBAG SENSOR LH)

C194788E03

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F25-3 (BBL-) - Body ground
    Ignition switch ON
    Below 1 V
    F25-4 (BBL+) - Body ground

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 8 (BBD+) and 15 (BBD-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F25-3 (BBL-) - F25-4 (BBL+)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    F25-3 (BBL-) - F25-4 (BBL+)
    Always
    1 MΩ or higher
    F25-3 (BBL-) - Body ground
    F25-4 (BBL+) - Body ground



NG
REPLACE FLOOR WIRE
OK


14.CHECK SIDE AIRBAG SENSOR LH
C158841E02
  1. Interchange the side airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1620 and B1625 are not output
    A
    DTC B1625 is output
    B
    DTC B1620 is output
    C

    HINT:
    Codes other than DTC B1620 and B1625 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK

B
REPLACE SIDE AIRBAG SENSOR LH
C


15.CHECK REAR AIRBAG SENSOR LH CIRCUIT

C194787E07

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    R14-2 (BCL+) - Body ground
    Ignition switch ON
    Below 1 V
    R14-1 (BCL-) - Body ground

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 2 (BCL-) and 1 (BCL+) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    R14-2 (BCL+) - R14-1 (BCL-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    R14-2 (BCL+) - R14-1 (BCL-)
    Always
    1 MΩ or higher
    R14-2 (BCL+) - Body ground
    R14-1 (BCL-) - Body ground



NG
REPLACE FLOOR WIRE
OK


16.CHECK FOR DTC


    C167367E05
  1. Connect the connectors to the side airbag sensor LH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1620 is output.

HINT:
Codes other than B1620 may be output at this time, but they are not related to this check.



NG
REPLACE REAR AIRBAG SENSOR LH
OK


17.CHECK SIDE AIRBAG SENSOR LH
C158841E02
  1. Interchange the side airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1620 and B1625 are not output
    A
    DTC B1620 is output
    B
    DTC B1625 is output
    C

    HINT:
    Codes other than DTC B1620 and B1625 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK

B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
C

REPLACE SIDE AIRBAG SENSOR LH