DTC B1635/24 Front Passenger Side Rear Airbag Sensor Malfunction |
| DTC Code | Detection Condition | Trouble Area |
| B1635/24 | When both conditions below are met:
|
|


| 1.CHECK VEHICLE CONDITION |
Check vehicle condition.
| Result | Proceed to |
| for LHD | A |
| for RHD | B |
|
| ||||
| A | |
| 2.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connector is properly connected to the rear airbag sensor RH.
|
| ||||
| OK | |
| 3.CHECK CONNECTORS |
Disconnect the connectors from the side airbag sensor RH and rear airbag sensor RH.
Check that the connector (on the rear airbag sensor RH side) is not damaged.
|
| ||||
| OK | |
| 4.CHECK REAR AIRBAG SENSOR RH CIRCUIT |

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| R13-2 (BCR+) - Body ground | Ignition switch ON | Below 1 V |
| R13-1 (BCR-) - Body ground |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Using a service wire, connect terminals 1 (BCR+) and 2 (BCR-) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| R13-2 (BCR+) - R13-1 (BCR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| R13-2 (BCR+) - R13-1 (BCR-) | Always | 1 MΩ or higher |
| R13-2 (BCR+) - Body ground | ||
| R13-1 (BCR-) - Body ground |
|
| ||||
| OK | |
| 5.CHECK FOR DTC |
![]() |
Connect the connectors to the side airbag sensor RH.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | |
| 6.CHECK SIDE AIRBAG SENSOR RH |
![]() |
Interchange the side airbag sensor LH with RH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1630 and B1635 are not output | A |
| DTC B1635 is output | B |
| DTC B1630 is output | C |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the side airbag sensor LH and RH to their original positions and connect the connectors to them.
|
| ||||
|
| ||||
| A | ||
| ||
| 7.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connector is properly connected to the rear airbag sensor LH.
|
| ||||
| OK | |
| 8.CHECK CONNECTORS |
Disconnect the connectors from the side airbag sensor LH and rear airbag sensor LH.
Check that the connector (on the rear airbag sensor LH side) is not damaged.
|
| ||||
| OK | |
| 9.CHECK REAR AIRBAG SENSOR LH CIRCUIT |

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| R14-2 (BCL+) - Body ground | Ignition switch ON | Below 1 V |
| R14-1 (BCL-) - Body ground |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Using a service wire, connect terminals 2 (BCL-) and 1 (BCL+) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| R14-2 (BCL+) - R14-1 (BCL-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| R14-2 (BCL+) - R14-1 (BCL-) | Always | 1 MΩ or higher |
| R14-2 (BCL+) - Body ground | ||
| R14-1 (BCL-) - Body ground |
|
| ||||
| OK | |
| 10.CHECK FOR DTC |
![]() |
Connect the connectors to the side airbag sensor LH.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | |
| 11.CHECK SIDE AIRBAG SENSOR LH |
![]() |
Interchange the side airbag sensor RH with LH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1630 and B1635 are not output | A |
| DTC B1635 is output | B |
| DTC B1630 is output | C |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.
|
| ||||
|
| ||||
| A | ||
| ||