Home › ENGINE ยท 2KD-FTV › INTAKE › TURBOCHARGER (w/ EGR Cooler)

TURBOCHARGER (w/ EGR Cooler) > REASSEMBLY

for Preparation Click here



1. INSTALL ACTUATOR ASSEMBLY WITH BRACKET (for Vacuum Controlled Actuator)


A148174E01

HINT:
The actuator push rod stroke is decided by the plate washer shown in the illustration.

  1. Using SST, apply pressure to the actuator.

    SST
    09992-00242  

    NOTICE:
    Never apply more than 147 kPa (1.50 kgf/cm2, 21.2 psi) of pressure to the actuator.



    A148173
  1. Install the actuator with the 2 bolts and E-ring.



    A148175E01
  1. Set the dial indicator as shown in the illustration.

  1. Using SST, apply 114 kPa (1.16 kgf/cm2, 16.4 psi) of pressure to the actuator, and measure the push rod stroke.

  1. Select the plate washer according to the table below.

    Stroke measurement mm (in.)
    Required plate washer thickness mm (in.)
    1.20 to 1.70 (0.0472 to 0.0669)
    -
    1.71 to 2.20 (0.0673 to 0.0866)
    0.5 (0.020)
    2.21 to 2.70 (0.0870 to 0.1063)
    1.0 (0.039)
    2.71 to 3.20 (0.1067 to 0.1260)
    1.5 (0.059)
    3.21 to 3.70 (0.1264 to 0.4517)
    2.0 (0.079)
    3.71 to 4.20 (0.1461 to 0.1654)
    2.5 (0.098)
    4.21 to 4.70 (0.1657 to 0.1850)
    3.0 (0.118)
    4.71 to 5.20 (0.1854 to 0.2047)
    3.5 (0.138)
    5.21 to 5.70 (0.2051 to 0.2244)
    4.0 (0.157)
    5.71 to 6.20 (0.2248 to 0.2441)
    4.5 (0.177)
    6.21 to 6.70 (0.2445 to 0.2638)
    5.0 (0.197)
    6.71 to 7.20 (0.2642 to 0.2827)
    5.5 (0.217)
    7.21 to 7.70 (0.2839 to 0.3031)
    6.0 (0.236)
    7.71 to 8.20 (0.3035 to 0.3228)
    6.5 (0.256)

    NOTICE:
    1. Use a combination of plate washers of 0.5 mm (0.020 in.), 1.0 mm (0.039 in.) and 3.0 mm (0.118 in.) thickness.
    1. Use plate washers of the same thickness between the 2 locations of the actuator and compressor housing.
    1. If the plate washer thickness exceeds 3.5 mm (0.138 in.), replace the actuator installation bolts with the bolts from the kit part.

  1. Using SST, apply 114 kPa (1.16 kgf/cm2, 16.4 psi) of pressure to the actuator, and install the selected plate washers between the actuator and compressor housing with the 2 bolts and E-ring.

    SST
    09992-00242  

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

  1. Using SST, apply 114 kPa (1.16 kgf/cm2, 16.4 psi) of pressure to the actuator, and measure the actuator push rod stroke.

    SST
    09992-00242  

    Standard stroke:
    1.20 to 1.70 mm (0.0472 to 0.0669 in.)

    If the stroke is outside specifications, select the plate washers again.

  1. Connect the actuator hose.

  1. Remove SST.

  1. Apply yellow paint from the actuator bolts to the actuator bracket to indicate that they have been correctly installed.