Home › BODY › EXTERIOR › FRONT BUMPER

FRONT BUMPER > REASSEMBLY

for Preparation Click here


HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL FRONT BUMPER EXTENSION LH (w/ Over Fender)


    B206033
  1. Install the extension with the 6 clips.



2. INSTALL FRONT BUMPER EXTENSION RH (w/ Over Fender)

HINT:
Use the same procedures described for the LH side.



3. INSTALL LOWER RADIATOR GRILLE


B206032
  1. Attach the 17 claws and guide to install the lower radiator grille.



    B211267
  1. w/ Headlight Cleaner System:
    Attach the 4 clamps to install the headlight cleaner hose.



4. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)


    B210371
  1. Attach the 2 claws to install the headlight washer actuator sub-assembly and install the bolt.

    Torque:
    1.1 N*m{ 11 kgf*cm , 10 in.*lbf }



    B210372
  1. Connect the hose as shown in the illustration.



5. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:
Use the same procedures described for the LH side.



6. INSTALL TYPE1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY LH (w/ Headlight Cleaner System)


    B182297
  1. Attach the 2 claws to install the headlight washer nozzle.



    E119841
  1. Return the headlight washer nozzle to its original position.



7. INSTALL TYPE1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:
Use the same procedures described for the LH side.



8. INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)


B206031
  1. Install the fog light with the 3 bolts.



9. INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:
Use the same procedures described for the LH side.



10. INSTALL RADIATOR GRILLE OR FRONT PANEL NAME PLATE (for 1GR-FE)
  1. Clean the lower radiator grille finish plate surface.

    1. Using a heat light, heat the lower radiator grille finish plate surface.

      Standard:
      Item
      Specified Condition
      Lower radiator grille finish plate
      20 to 30°C (68 to 86°F)

      NOTICE:
      Do not heat the lower radiator grille finish plate excessively.

    2. Remove the double-sided tape from the lower radiator grille finish plate.

    3. Wipe off any tape adhesive residue with cleaner.



    B207663E01
  1. Install a new name plate.

    1. Remove the peeling paper from the face of the name plate.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

    2. Install the name plate to the lower radiator grille finish plate with 2 new spring nuts.



11. INSTALL RADIATOR GRILLE (OR FRONT PANEL) EMBLEM


    B211266
  1. for Type A:

    1. Attach the 3 claws to install the emblem to the radiator grille.



    B207579E03
  1. for Type B:

    1. Attach the 3 claws to install the emblem to the lower radiator grille moulding.



12. INSTALL LOWER RADIATOR GRILLE MOULDING (for Type B)


B210079
  1. Install the lower radiator grille moulding with the 16 screws.



13. INSTALL RADIATOR GRILLE MOULDING


    B210701
  1. Install the radiator grille moulding with the 9 screws.



14. INSTALL NO. 1 RADIATOR GRILLE SEAL


B206035E01
  1. Wipe off any tape adhesive residue with cleaner.

  1. Remove the peeling paper from the face of the double-sided tape of a new radiator grille seal.

    HINT:
    After removing the peeling paper, keep the exposed adhesive free from foreign matter.

  1. Install the radiator grille seal.