Home › BODY › SEAT › FRONT SEAT ASSEMBLY (for Power Seat)

FRONT SEAT ASSEMBLY (for Power Seat) > DISASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.



1. REMOVE RECLINING POWER SEAT SWITCH KNOB


    B207076E01
  1. Apply protective tape around the cushion shield.

  1. Using a screwdriver, detach the 2 claws and remove the knob.

    HINT:
    Tape the screwdriver tip before use.



2. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    B207077E01
  1. Using a screwdriver, detach the 4 claws and remove the knob.

    HINT:
    Tape the screwdriver tip before use.



3. REMOVE FRONT SEAT CUSHION SHIELD RH


    B207078
  1. Remove the 2 screws.



    B207039
  1. Remove the 3 screws.

  1. Detach the claw and guide.

  1. Remove the cushion shield.



4. REMOVE FRONT INNER NO. 1 SEAT CUSHION SHIELD


    B207079
  1. Remove the 2 screws.

  1. Detach the 2 claws and remove the cushion shield.



5. REMOVE FRONT POWER SEAT SWITCH


    B207080
  1. Remove the 3 screws.

  1. Disconnect the connector and remove the switch.



6. REMOVE FRONT SEAT CUSHION INNER SHIELD RH


    B207199
  1. Remove the screw.

  1. Pull the cushion inner shield to detach the claw and guide.



    B207617
  1. Pull the cushion inner shield to detach the claw and remove the cushion inner shield.



7. REMOVE FRONT SEAT INNER BELT ASSEMBLY RH


B087811E01
  1. Detach the clamp.



    B089297E01
  1. Detach the wire harness from the clamp.

  1. Remove the nut and seat belt.

  1. Remove the buckle cover.



8. REMOVE FRONT SEAT CUSHION COVER RH
  1. Remove the cover.



9. REMOVE SEAT CUSHION COVER WITH PAD


    B207501
  1. Remove the hog rings.



  1. Detach the hooks and remove the seat cushion cover with pad.


    B207081



10. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER


    B207624
  1. Remove the hog rings and seat cushion cover.



11. REMOVE SEPARATE TYPE FRONT SEATBACK COVER


    B207085
  1. Remove the hog rings from the wires of the seatback cover. Then roll up the seatback cover.



    B207086
  1. Remove the hog rings and roll up the seatback cloth.



    B207087
  1. Remove the hog rings and detach the strap of the seatback cover. Then roll up the seatback cover.



    B257946
  1. Remove the hog rings from the center of the seatback pad and roll up the seatback cover.



    B207581
  1. Remove the hog rings from the upper part of the seatback pad. Then roll up the seatback cover.



    B207089
  1. Detach the 4 claws and remove the 2 headrest supports.



    B207091
  1. Remove the hog rings and seatback cover.



12. REMOVE SEPARATE TYPE FRONT SEATBACK PAD


    B207090
  1. Remove the seatback pad.



13. REMOVE NO. 1 SEATBACK CLOTH


    B207092
  1. Remove the seatback cloth.



14. REMOVE RECLINING ADJUSTER INSIDE COVER RH


    B207093
  1. Remove the screw.

  1. Detach the claw and remove the cover.



15. REMOVE RECLINING ADJUSTER INSIDE COVER RH


    B171585E02
  1. Remove the screw.

  1. Detach the guide and remove the cover.



16. REMOVE RECLINING ADJUSTER INSIDE COVER LH


    B207094
  1. Remove the screw.

  1. Detach the claw and remove the cover.



17. REMOVE RECLINING ADJUSTER INSIDE COVER LH


    B171583E02
  1. Remove the screw.

  1. Detach the guide and remove the cover.



18. REMOVE FRONT POWER SEAT MOTOR ASSEMBLY (for Reclining)


    B207267
  1. Detach the 8 hooks and remove the seatback spring.

  1. Disconnect the connector.



    B207099
  1. Detach the 6 claws and remove the push nut from the reclining rod.



    B206606
  1. Remove the reclining rod.



    B206607
  1. Using a 4 mm socket hexagon wrench, remove the 3 bolts and motor.



19. REMOVE FRONT POWER SEAT MOTOR ASSEMBLY (for Slide)


    B207048
  1. Detach the 2 wire harness clamps.

  1. Detach the 4 clamps indicated by the arrows in the illustration and remove the seat cushion spring.



    B206614
  1. Remove the 4 bolts and seat cushion frame.



    B206610
  1. Put matchmarks on the seat track rail and sliding unit of the seat frame.

  1. Disconnect the connector.



    B108592
  1. Connect the positive (+) battery terminal to terminal 1 of the power seat motor and the negative (-) battery terminal to terminal 2 and slide the seat to the foremost position.



    B207101
  1. Detach the claw and disconnect the connector from the seat frame.

  1. Loosen the 2 nuts.



    B108592
  1. Connect the positive (+) battery terminal to terminal 2 of the power seat motor and the negative (-) battery terminal to terminal 1 and slide the seat to the rearmost position.



    B206612
  1. Using a 5 mm socket hexagon wrench, remove the 2 bolts.

  1. Using a 4 mm socket hexagon wrench, remove the 4 bolts.

  1. Remove the 2 nuts and front power seat motor assembly with slide cable.

    NOTICE:
    Do not apply excessive force to the slide cable (do not bend the side cable 60° or more).



    B207102
  1. Remove the slide cable.



20. REMOVE FRONT POWER SEAT MOTOR ASSEMBLY (for Rear Lifter)


    B207048
  1. Detach the 2 wire harness clamps.

  1. Detach the 4 clamps indicated by the arrows in the illustration and remove the seat cushion spring.



    B206614
  1. Remove the 4 bolts and seat cushion frame.



    B206613
  1. Using a T40 "TORX" socket wrench, remove the 2 "TORX" bolts for the tilt rod.

  1. Remove the nut and tilt rod.



    B207168E01
  1. Disconnect the connector.

  1. Using a T40 "TORX" socket wrench, remove the "TORX" bolt for the adjust screw.

  1. Using a 4 mm socket hexagon wrench, remove the 2 bolts and motor.

    HINT:
    When the adjust screw is locked in the uppermost or lowermost position, turn the screw to release the lock before removing the motor unit.



21. REMOVE FRONT LOWER SEAT CUSHION SHIELD RH


    B207095
  1. Remove the screw.

  1. Detach the 4 claws and remove the lower seat cushion shield.



22. REMOVE FRONT LOWER SEAT CUSHION SHIELD LH


    B207096
  1. Remove the screw.

  1. Detach the 4 claws and remove the lower seat cushion shield.



23. REMOVE FRONT SEAT WIRE RH


    B207514
  1. Disconnect the connector.

  1. Detach the wire harness clamp.

  1. Detach the 2 claws and remove the seat wire.



24. REMOVE FRONT NO. 2 SEAT WIRE RH


    B207103
  1. Detach the 2 wire harness clamps and remove the seat wire.



25. REMOVE SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY


    B207098
  1. Remove the 4 bolts and seatback spring.