Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > Brake Warning Light Remains ON

for Preparation Click here


DESCRIPTION

When one of the following conditions is met, the brake warning light remains on:
  1. The skid control ECU connector is disconnected from the skid control ECU.
  2. The brake fluid level is insufficient.
  3. The parking brake is applied.
  4. The vacuum inside the brake booster decreases.
  5. There is an open circuit in the harness between the combination meter and the skid control ECU.
  6. EBD operation has been disabled.

WIRING DIAGRAM


C198928E01


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the brake actuator assembly, perform zero point calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK FOR DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC not output
    A
    DTC output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS
A


2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU IG1 TERMINAL)


    C160263E89
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    S35-34 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU GND1 TERMINAL)


    C160263E85
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S35-1 (GND1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK BRAKE BOOSTER ASSEMBLY
  1. Check the brake booster assembly (for TSAM Made LHD: Click here, for TSAM Made RHD: Click here, for TMT Made LHD: Click here, for TMT Made RHD: Click here).



NG
REPLACE BRAKE BOOSTER ASSEMBLY
OK


6.INSPECT BRAKE FLUID LEVEL WARNING SWITCH


    C190497E01
  1. Turn the ignition switch off.

  1. Remove the reservoir filler cap and strainer.

  1. Disconnect the brake fluid level warning switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    A float is located inside the reservoir. Its position can be changed by increasing or decreasing the level of brake fluid.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Brake fluid level warning switch OFF (Float up)
    1.9 to 2.1 kΩ
    1 - 2
    Brake fluid level warning switch ON (Float down)
    Below 1 Ω



NG
REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY
OK


7.CHECK VACUUM WARNING SWITCH ASSEMBLY


    C190515E01
  1. Turn the ignition switch off.

  1. Disconnect the vacuum warning switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Engine idling
    10 kΩ or higher
    1 - 2
    Ignition switch off and brake pedal depressed a number of times to release vacuum
    Below 1 Ω



NG
REPLACE VACUUM WARNING SWITCH ASSEMBLY
OK


8.INSPECT PARKING BRAKE SWITCH ASSEMBLY


    C167308E02
  1. Turn the ignition switch off.

  1. Disconnect the parking brake switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Parking brake switch ON
    (Switch pin free)
    Below 1 Ω
    1 - Body ground
    Parking brake switch OFF
    (Switch pin pushed in)
    10 kΩ or higher



NG
REPLACE PARKING BRAKE SWITCH ASSEMBLY
OK


9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)

C190486E04

  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU connector.

  1. Disconnect the combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S35-8 (BRL) - C8-26
    Always
    Below 1 Ω
    S35-8 (BRL) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BODY GROUND)


    C137771E07
  1. Turn the ignition switch off.

  1. Disconnect the combination meter connector.

  1. Disconnect the skid control ECU connector.

  1. Disconnect the brake fluid level warning switch connector.

  1. Disconnect the vacuum warning switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C8-36 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.READ VALUE USING INTELLIGENT TESTER (BRAKE WARNING LIGHT)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and the tester on.

  1. Select the Data List mode on the intelligent tester (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    Brake Warning Light
    Brake warning light /
    ON or OFF
    ON: Brake warning light ON
    OFF: Brake warning light OFF
    -

  1. Perform the Active Test of the skid control ECU using the intelligent tester (Click here).


ABS/VSC/TRC 
Tester Display
Test Part
Control Range
Diagnostic Note
Brake Warning Light
Brake warning light
Warning light ON / OFF
Observe combination meter

Result 
Result
Proceed to
Data List Display
Data List Display When Performing Active Test ON/OFF Operation
ON
Does not change between ON and OFF
A
Changes between ON and OFF
B
OFF
Does not change between ON and OFF
A
Changes between ON and OFF
B


B
REPLACE COMBINATION METER ASSEMBLY
A

REPLACE BRAKE ACTUATOR ASSEMBLY