Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > Slip Indicator Light Remains ON

for Preparation Click here


DESCRIPTION

The slip indicator light blinks during VSC and/or TRC operation.
When the system fails, the slip indicator light comes on to warn the driver (Click here).
Pressing the VSC OFF switch turns off traction control and pressing and holding this switch turns off traction control and VSC. If traction control turns off, the slip indicator light will come on.
When the transfer position is L4, traction control is stopped and the slip indicator light turns on.

WIRING DIAGRAM

Refer to VSC OFF Indicator Light Remains ON (Click here).

INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).

1.CHECK FOR DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC not output
    A
    DTC output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS
A


2.READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to on and the intelligent tester on.

  1. Select the Data List mode on the intelligent tester (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    TRC/VSC Off Mode
    VSC OFF switch / Normal, TRC OFF or VSC OFF
    Normal: Normal mode
    TRC OFF: TRC off mode
    VSC OFF: VSC off mode
    -

  1. Using the intelligent tester, check that the condition on the intelligent tester changes according to VSC OFF switch operation.

    OK:
    The intelligent tester display changes according to VSC OFF switch operation.



NG
Go to step 4
OK


3.READ VALUE USING INTELLIGENT TESTER (SLIP INDICATOR LIGHT)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and the tester on.

  1. Select the Data List mode on the intelligent tester (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    Slip Indicator Light
    Slip indicator light /
    ON or OFF
    ON: Slip indicator light ON
    OFF: Slip indicator light OFF
    -

  1. Perform the Active Test of the skid control ECU using the intelligent tester (Click here).


ABS/VSC/TRC 
Tester Display
Test Part
Control Range
Diagnostic Note
Slip Indicator Light
Slip indicator light
Indicator light ON / OFF
Observe combination meter

Result 
Result
Proceed to
Data List Display
Data List Display When Performing Active Test ON/OFF Operation
ON
Does not change between ON and OFF
A
Changes between ON and OFF
B
OFF
Does not change between ON and OFF
A
Changes between ON and OFF
B


B
REPLACE COMBINATION METER ASSEMBLY
A

REPLACE BRAKE ACTUATOR ASSEMBLY 

4.INSPECT VSC OFF SWITCH


    C190520E01
  1. Turn the ignition switch off.

  1. Remove the VSC OFF switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 - 4
    Switch is pushed and held
    Below 1 Ω
    3 - 4
    Switch is not pushed
    10 kΩ or higher



NG
REPLACE VSC OFF SWITCH
OK


5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)

C190629E04

  1. Turn the ignition switch off.

  1. Disconnect the VSC OFF switch connector.

  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S35-30 (CSW) - V8-3
    Always
    Below 1 Ω
    S35-30 (CSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU EXI3 TERMINAL)


    C160263E90
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    S35-28 (EXI3) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY