Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > VSC OFF Indicator Light Remains ON

for Preparation Click here


DESCRIPTION

If the skid control ECU stores a DTC, the VSC OFF indicator light blinks in the combination meter.
Pressing the VSC OFF switch turns off traction control and pressing and holding this switch turns off traction control and VSC. If VSC turns off, the VSC OFF indicator light will come on.
When the transfer position is L4, traction control is stopped and the slip indicator light turns on.

WIRING DIAGRAM


C198959E01


INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).

1.READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to on and the intelligent tester on.

  1. Select the Data List mode on the intelligent tester (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    TRC/VSC Off Mode
    VSC OFF switch / Normal, TRC OFF, Unknown or VSC OFF
    Normal: Normal mode
    TRC OFF: TRC off mode
    VSC OFF: VSC off mode
    -

  1. Using the intelligent tester, check that the condition on the intelligent tester changes according to VSC OFF switch operation.

    OK:
    The intelligent tester display changes according to VSC OFF switch operation.



NG
Go to step 3
OK


2.READ VALUE USING INTELLIGENT TESTER (VSC WARNING LIGHT)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and the tester on.

  1. Select the Data List mode on the intelligent tester (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    VSC Warning Light
    VSC OFF indicator light / ON or OFF
    ON: Indicator light ON
    OFF: Indicator light OFF
    -

  1. Perform the Active Test of the skid control ECU using the intelligent tester (Click here).


ABS/VSC/TRC 
Tester Display
Test Part
Control Range
Diagnostic Note
VSC Warning Light
VSC OFF indicator light
Indicator light ON / OFF
Observe combination meter

Result 
Result
Proceed to
Data List Display
Data List Display When Performing Active Test ON/OFF Operation
ON
Does not change between ON and OFF
A
Changes between ON and OFF
B
OFF
Does not change between ON and OFF
A
Changes between ON and OFF
B


B
REPLACE COMBINATION METER ASSEMBLY
A

REPLACE BRAKE ACTUATOR ASSEMBLY 

3.INSPECT VSC OFF SWITCH


    C190520E01
  1. Turn the ignition switch off.

  1. Remove the VSC OFF switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 - 4
    Switch is pushed and held
    Below 1 Ω
    3 - 4
    Switch is not pushed
    10 kΩ or higher



NG
REPLACE VSC OFF SWITCH
OK


4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)


  1. Turn the ignition switch off.


    C190629E04

  1. Disconnect the VSC OFF switch connector.

  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S35-30 (CSW) - V8-3
    Always
    Below 1 Ω
    S35-30 (CSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU EXI3 TERMINAL)


    C160263E90
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    S35-28 (EXI3) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY