Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) > SYSTEM DESCRIPTION

for Preparation Click here



GENERAL
  1. The air conditioning system has the following features:

    1. The air conditioning amplifier is equipped with a self-diagnosis function. If there is a malfunction in the system, it stores DTC(s) in its memory and the air conditioning switch indicator blinks.
    2. The air conditioning amplifier receives the vehicle speed signal from the combination meter.
    3. The damper servo (air inlet damper servo motor), air mix damper servo and mode damper servo (air vent damper servo motor) rely on their built-in pulse sensors to detect their respective motor rotation angles.
    4. The servo motor rotation angle's zero point calibration is necessary in the following situations: 1) the servo motor deviates from the calibrated position, 2) the air conditioning amplifier's backup power source is cut, or 3) the air conditioning amplifier or servo motor is replaced.
      For 1, when the ignition switch is turned off, zero point calibration of the air conditioning amplifier is automatically performed. For 2 and 3, when the backup power source returns and the ignition switch is turned to ON, zero point calibration of the air conditioning amplifier is automatically performed.
      While zero point calibration is being performed, the following occurs: 1) the air conditioning amplifier's DEF indicator blinks at 1 second intervals, but the air conditioning amplifier's other outputs are disabled; and 2) the A/C system's switches do not function.
    5. The air conditioning unit has been made compact and lightweight by placing the evaporator and the heater core horizontally, above and below in the unit, and adopting a film type slide door for the air mix door.
    6. The Positive Temperature Coefficient (PTC) heater system contains a PTC heater that heats the air that has passed though the heater core to ensure proper heater performance.


MODE POSITION AND DAMPER OPERATION

E219149E01


Function of Main Damper 
Control Damper
Control Position
Damper Position
Operation
Air Inlet Control Damper
E113403
FRESH
A
Brings in fresh air.
E113404
RECIRCULATION
B
Recirculates internal air.
Air Mix Control Damper
MAX COLD - MAX HOT
C, D, E
Varies mixture ratio of cool air and warm air in order to regulate temperature continuously from HOT to COLD.
Mode Control Damper
E106660
DEF
H, K
Defrosts windshield through center defroster and side registers.
E106659
FOOT / DEF
H, I
Defrosts windshield through center defroster and side registers. Air is also blown out from footwell register ducts.
E106658
FOOT
G, I
Air blows out of footwell register ducts and side registers. Air also blows out slightly from center defroster.
E106657
BI - LEVEL
F, J
Air blows out of center register, side registers and footwell register ducts.
E106656
FACE
F, K
Air blows out of center register and side registers.

AIR OUTLETS AND AIR FLOW VOLUME

E165580E01


Air Outlet Mode
A
B
C
D
Center Face
Side Face
Foot
Defroster
Face
E106656
E107019
E107019
E107318
E107318
BI-LEVEL
E106657
E107019
E107019
E107317
E107318
FOOT
E106658
E107318
E107317
E107019
E107317
FOOT / DEF
E106659
E107318
E107317
E107019
E107019
DEF
E106660
E107318
E107317
E107318
E107019

HINT:
The circle size (○) is proportional to the amount of air flow.


E165601E02


Air Outlet Mode
A
B
C
D
Center Face
Side Face
Foot
Defroster
Face
E106656
E107019
E107019
E107318
E107318
BI-LEVEL
E106657
E107019
E107019
E107317
E107318
FOOT
E106658
E107318
E107317
E107019
E107317
FOOT / DEF
E106659
E107318
E107317
E107019
E107019
DEF
E106660
E107318
E107317
E107318
E107019

HINT:
The circle size (○) is proportional to the amount of air flow.