Home › DRIVE LINE › DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock)

REAR DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock) > REASSEMBLY > Preparation



SST 
I000023
09308-00010
Oil Seal Puller


I002418
09316-60011
Transmission & Transfer Bearing
Replacer

I002419
(09316-00011)
Replacer Pipe


I002420
(09316-00021)
Replacer A


I002422
(09316-00041)
Replacer C


I000032
09330-00021
Companion Flange Holding Tool


I000883
(09330-00030)
Pin


I000677
09504-00011
Differential Side Bearing
Adjusting Nut Wrench

I000040
09506-30012
Differential Drive Pinion Rear
Bearing Cone Replacer

I000395
09554-30011
Differential Oil Seal Replacer


I000744
09636-20010
Upper Ball Joint Dust Cover
Replacer

I010020
09930-00010
Drive Shaft Nut Chisel


I010021
(09931-00010)
Handle


I010022
(09931-00020)
Nut Chisel


I002108
09950-30012
Puller A Set


I002109
(09951-03010)
Upper Plate


I002110
(09953-03010)
Center Bolt


I002111
(09954-03010)
Arm


I002142
(09955-03030)
Lower Plate 130


I002146
(09956-03040)
Adapter 22


I002306
09950-60010
Replacer Set


I002333
(09951-00430)
Replacer 43


I002337
(09951-00470)
Replacer 47


I002338
(09951-00480)
Replacer 48


I002345
(09951-00550)
Replacer 55


I002307
09950-70010
Handle Set


I002346
(09951-00560)
Replacer 56


I002347
(09951-00570)
Replacer 57


I002357
(09951-07150)
Handle 150


I002061
09960-10010
Variable Pin Wrench Set


I002062
(09962-01000)
Variable Pin Wrench Arm Assembly


I002064
(09963-00700)
Pin 7




EQUIPMENT
Brass bar
-
Chisel
-
Dial indicator
-
Feeler gauge
-
Hammer
-
Micrometer
-
Needle nose pliers
-
Plastic hammer
-
Press
-
Red lead
-
Screwdriver
-
Tape
-
Torque wrench
-
Vernier calipers
-


LUBRICANT / Front differential
Item
Capacity
Oil grade
Classification
w/ A.D.D.
1.60 to 1.70 liters (1.69 to 1.80 US qts, 1.40 to 1.50 Imp. qts.)
Hypoid gear oil API GL-5 or equivalent
Above-18°C (0°F): SAE 90
Below-18°C (0°F): SAE 75W-90
w/o A.D.D.
1.40 to 1.50 liters (1.48 to 1.59 US qts, 1.23 to 1.31 Imp. qts.)
Above-18°C (0°F): SAE 90)
Below-18°C (0°F): SAE 85W-90

LUBRICANT / Rear differential (TMT made)
Item
Capacity
Oil grade
Classification
2WD
3.15 to 3.25 liters (3.30 to 3.43 US qts, 2.77 to 2.86 Imp. qts.)
Hypoid gear oil API GL-5 or equivalent
Above-18°C (0°F): SAE 90
Below-18°C (0°F): SAE 85W-90
2WD (for LSD)
Hypoid gear oil LSD API GL-5 or equivalent
4WD
3.30 to 3.40 liters (3.49 to 3.59 US qts, 2.90 to 2.99 Imp. qts.)
Hypoid gear oil API GL-5 or equivalent
4WD (for LSD)
Hypoid gear oil LSD API GL-5 or equivalent

LUBRICANT / Rear differential (TSAM made)
Item
Capacity
Oil grade
Classification
2WD and made for DANA
2.30 to 2.40 liters (2.43 to 2.54 US qts, 2.02 to 2.11 Imp. qts.)
Hypoid gear oil API GL-5 or equivalent
Above-18°C (0°F): SAE 90
Below-18°C (0°F): SAE 85W-90
4WD and Pre-runner
2.40 to 2.50 liters (2.54 to 2.64 US qts, 2.11 to 2.20 Imp. qts.)
2WD (for LSD)
3.15 to 3.25 liters (3.30 to 3.43 US qts, 2.77 to 2.86 Imp. qts.)
Hypoid gear oil LSD API GL-5 or equivalent
4WD (for LSD)
3.30 to 3.40 liters (3.49 to 3.59 US qts, 2.90 to 2.99 Imp. qts.)
w/ Differential lock
2.85 to 2.95 liters (3.01 to 3.12 US qts, 2.51 to 2.60 Imp. qts.)
Hypoid gear oil API GL-5 or equivalent
2 Pinion type
2.90 to 3.00 liters (3.07 to 3.17 US qts, 2.55 to 2.64 Imp. qts.)


RECOMMENDED TOOLS
I002297
09011-12301
Socket Wrench 30 mm
-
I000322
09031-00030
Pin Punch
-
I001236
09044-00010
Torx Socket E14
-
I000114
09905-00012
Snap Ring No.1 Expander
-
I000115
09905-00013
Snap Ring Pliers
-

HINT:
"Torx" is a registered trademark of Textron Inc.



SSM
Toyota Genuine Adhesive 1360K, Three Bond 1360K or equivalent
-
Toyota Genuine Seal Packing 1281 Three Bond 1281 or equivalent
-
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
-