ENGINE UNIT > GENERAL



OUTLINE
  1. The 1GR-FE engine is a V-type, 6-cylinder, 4.0-liter, 24-valve DOHC engine.

  2. On this engine, the Variable Valve Timing-intelligent (VVT-i) system, Acoustic Control Induction System (ACIS), and the Electronic Throttle Control System-intelligent (ETCS-i) are used. These control functions have been optimized to further improve engine performance and fuel economy, and to reduce exhaust emissions.

  3. This engine has been made compact and lightweight through the use of an aluminum cylinder block and a plastic type intake air chamber, fuel delivery pipe, and water inlet pipe.


SPECIFICATION

No. of Cyls. and Arrangement
6-cylinder, V-type
Valve Mechanism
24-valve DOHC, Chain Drive (with VVT-i)
Combustion Chamber
Pentroof Type
Manifolds
Cross-flow
Fuel System
Sequential Multiport Fuel Injection (SFI)
Ignition System
Direct Ignition System (DIS)
Displacement
3956 cm3 (241.4 cu. in.)
Bore x Stroke
94.0 mm x 95.0 mm (3.70 in. x 3.74 in.)
Compression Ratio
10.0 : 1
Max. Output [SAE-NET]
175 kW @ 5200 rpm
Max. Torque [SAE-NET]
376 N*m @ 3800 rpm
Valve Timing
Intake
Open
42° to - 8° BTDC
Closed
10° to 60° ABDC
Exhaust
Open
54° BBDC
Closed
2° ATDC
Spark Plug
Manufacturer
DENSO
Type
K20HR-U11
Plug Gap
1.0 mm to 1.1 mm (0.0394 in. to 0.0433 in.)
Firing Order
1 - 2 - 3 - 4 - 5 - 6
Research Octane Number
95 or higher
Emission Regulation
EURO 3
Engine Service Mass (Reference)*
166 kg (366 lb)

HINT:
*: Weight shows the figure with oil and coolant fully filled.


W104439E01


MAIN FEATURES
  1. This engine has been able to achieve the following performance through the use of the items listed below:

    1. High performance and fuel economy

    2. Low noise and vibration

    3. Lightweight and compact design

    4. Good serviceability

    5. Clean emissions

      Item
      (1)
      (2)
      (3)
      (4)
      (5)
      Engine Proper
      An upright intake port is used.
      ○
      -
      ○
      -
      -
      A taper squish shape is used for the combustion chamber.
      ○
      -
      -
      -
      ○
      A steel-laminate type cylinder head gasket is used.
      ○
      -
      -
      -
      -
      Spiny-type liners are used in the cylinder bores.
      ○
      -
      ○
      -
      -
      The piston skirt is coated with resin.
      ○
      ○
      -
      -
      ○
      A No. 1 oil pan made of aluminum alloy is used.
      ○
      ○
      ○
      -
      -
      Valve Mechanism
      Timing chains and chain tensioners are used.
      ○
      -
      ○
      -
      -
      Shim-less type valve lifters are used.
      ○
      -
      ○
      -
      -
      The Variable Valve Timing-intelligent (VVT-i) system is used.
      ○
      -
      -
      -
      ○
      Lubrication System
      A water-cooled type oil cooler is used.
      ○
      -
      -
      -
      -
      Intake and Exhaust System
      An intake air surge tank made of plastic is used.
      -
      -
      ○
      -
      -
      A linkless-type throttle body is used.
      -
      -
      ○
      ○
      -
      Three-Way Catalyst (TWCs) are used.
      -
      -
      -
      -
      ○
      Fuel System
      12-hole type fuel injector assemblies are used to improve the atomization of fuel.
      ○
      -
      -
      -
      ○
      Ignition System
      Long-reach type spark plugs are used.
      ○
      -
      -
      -
      -
      Serpentine Belt Drive System
      A serpentine belt drive system is used.
      -
      -
      ○
      ○
      -
      Engine Control
      The Electronic Throttle Control System-intelligent (ETCS-i) is used.
      ○
      -
      -
      -
      ○
      The Direct Ignition System (DIS) makes ignition timing adjustment unnecessary.
      ○
      -
      -
      ○
      ○
      The Acoustic Control Induction System (ACIS) is used.
      ○
      -
      -
      -
      ○