DTC P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2) |
DTC P0038 Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2) |
DTC P0057 Oxygen Sensor Heater Control Circuit Low (Bank 2 Sensor 2) |
DTC P0058 Oxygen Sensor Heater Control Circuit High (Bank 2 Sensor 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0037 P0057 | Heated oxygen sensor (HO2S) heater current less than 0.3 A (1 trip detection logic) |
|
| P0038 P0058 | Heated oxygen sensor (HO2S) heater current more than 2 A (1 trip detection logic) |
|
| 1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the H12 and H13 heated oxygen sensor connectors.
Measure the resistance of the sensor.
| Tester Connection | Condition | Specified Condition |
| 1 (HT1B) - 2 (+B) | 20°C (68°F) | 11 to 16 Ω |
| 1 (HT1B) - 4 (E2) | - | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| 1 (HT2B) - 2 (+B) | 20°C (68°F) | 11 to 16 Ω |
| 1 (HT2B) - 4 (E2) | - | 10 kΩ or higher |
|
| ||||
| OK | |
| 2.INSPECT INTEGRATION NO.1 RELAY (MAIN RELAY) |
![]() |
Disconnect the 1J integration relay connector from the engine room junction block (Click here).
Measure the voltage of the MAIN relay.
| Tester Connection | Condition | Specified Condition |
| 1J-5 - Body ground | Ignition switch ON | 10 to 14 V |
|
| ||||
| OK | |
| 3.CHECK ECM (HT1B, HT2B VOLTAGE) |
![]() |
Turn the ignition switch ON.
Measure the voltage of the ECM connector.
| Tester Connection | Specified Condition |
| E15-1 (HT1B) - E17-1 (E1) | 9 to 14 V |
| E16-5 (HT2B) - E17-1 (E1) | 9 to 14 V |
|
| ||||
| NG | |
| 4.CHECK WIRE HARNESS (HEATED OXYGEN SENSOR - ECM AND INTEGRATION RELAY (MAIN RELAY)) |
![]() |
Disconnect the H12 or H13 sensor connectors.
Disconnect the E15 or E16 ECM connector.
Disconnect the 1J integration relay connector from the engine room junction block (Click here).
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| H12-1 (HT1B) - E15-1 (HT1B) | Below 1 Ω |
| H12-2 (+B) - 1J-5 | Below 1 Ω |
| H12-1 (HT1B) or E15-1 (HT1B) - Body ground | 10 kΩ or higher |
| H12-2 (+B) or 1J-5 - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| H13-1 (HT2B) - E16-5 (HT2B) | Below 1 Ω |
| H13-2 (+B) - 1J-5 | Below 1 Ω |
| H13-1 (HT2B) or E16-5 (HT2B) - Body ground | 10 kΩ or higher |
| H13-2 (+B) or 1J-5 - Body ground | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||