SFI SYSTEM > DATA LIST / ACTIVE TEST |
| DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the intelligent tester, read the Data List.
| Various Vehicle Conditions 1 (All Data) |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Vehicle Speed | Vehicle speed/ Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Actual vehicle speed | Yes |
Diagnostic Note:
| |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Engine Speed | Engine speed/ Min.: 0 rpm, Max.: 16383 rpm | 600 to 700 rpm: Idling | Yes |
| Diagnostic Note: When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 or varies greatly from the actual engine speed. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Calculate Load | Load calculated by ECM/ Min.: 0%, Max.: 100% | - | Yes |
| Diagnostic Note: This is the engine load calculated based on the estimated intake manifold pressure. Calculate Load = Estimated intake manifold pressure / maximum intake manifold pressure x 100 (%) (For example, when the estimated intake manifold pressure is the same as atmospheric pressure, Calculate Load is 100%.) | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| MAF | Airflow rate from Mass Air Flow (MAF) meter/ Min.: 0 gm/s, Max.: 655.35 gm/s | 1.0 to 4.0 gm/s: Idling 4.0 to 15.0 gm/s: 2500 rpm (without load) | Yes |
| Diagnostic Note: This is the intake air amount from the mass air flow meter. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Atmosphere Pressure | Atmospheric pressure/ Min.: 0 kPa, Max.: 255 kPa | Equivalent to atmospheric pressure (absolute pressure) | Yes |
Diagnostic Note:
| |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Coolant Temp | Coolant temperature/ Min.: -40°C, Max.: 140°C | 80 to 95°C (176 to 203°F): After warming up | Yes |
| Diagnostic Note: This is the engine coolant temperature.
| |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Intake Air | Intake air temperature/ Min.: -40°C, Max.: 140°C | Equivalent to temperature at location of mass air flow meter | Yes |
Diagnostic Note:
| |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Engine Run Time | Engine run time/ Min.: 0 s, Max.: 65535 s | Time after engine start | Yes |
| Diagnostic Note: This is the time elapsed since the engine started.
| |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Initial Engine Coolant Temp | Initial engine coolant temperature/ Min.: -40°C, Max.: 215°C | - | Yes |
| Diagnostic Note: This is the coolant temperature stored when the ignition switch is turned to ON. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Initial Intake Air Temp | Initial intake air temperature/ Min.: -40°C, Max.: 140°C | - | Yes |
| Diagnostic Note: This is the intake air temperature stored when the ignition switch is turned to ON. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Battery Voltage | Battery voltage/ Min.: 0 V, Max.: 65.535 V | 11 to 14 V: Idling | Yes |
| Diagnostic Note: If 11 V or less, characteristics of some electrical components may change. | |||
| Throttle Control (Ptrl Throttle) |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Accel Sens. No.1 Volt % | Absolute Accelerator Pedal Position (APP) No. 1/ Min.: 0%, Max.: 100% | 10 to 22%: Accelerator pedal released 52 to 90%: Accelerator pedal fully depressed | Yes |
| Diagnostic Note: The accelerator pedal position sensor No. 1 output is converted using 5 V = 100%.
| |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Accel Sens. No.2 Volt % | Absolute APP No. 2/ Min.: 0%, Max.: 100% | 24 to 40%: Accelerator pedal released 68 to 95%: Accelerator pedal fully depressed | Yes |
| Diagnostic Note: The accelerator pedal position sensor No. 2 output is converted using 5 V = 100%. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Accel Sensor Out No.1 | APP sensor No. 1 voltage/ Min.: 0 V, Max.: 4.98 V | 0.5 to 1.1 V: Accelerator pedal released 2.6 to 4.5 V: Accelerator pedal fully depressed | No |
| Diagnostic Note: This is the raw voltage from the accelerator pedal position sensor No. 1. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Accel Sensor Out No.2 | APP sensor No. 2 voltage/ Min.: 0 V, Max.: 4.98 V | 1.2 to 2.0 V: Accelerator pedal released 3.4 to 4.75 V: Accelerator pedal fully depressed | No |
| Diagnostic Note: This is the raw voltage from the accelerator pedal position sensor No. 2. Accelerator pedal position sensor No. 2 is used to monitor accelerator pedal position sensor No. 1. When there is a malfunction in sensor No. 1, the ECM uses sensor No. 2 to control the engine. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Accelerator Idle Position | Whether or not accelerator pedal position sensor detecting released accelerator pedal/ ON or OFF | ON: Accelerator pedal released | No |
| Diagnostic Note: This is a parameter calculated by the ECM which indicates whether the accelerator pedal is in the learned idle position. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Accel Fully Close #1 (AD) | Accelerator fully closed value No. 1 (AD)/ Min.: 0 V, Max.: 4.9 V | - | No |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Accel Fully Close Learn #1 | Accelerator fully released learned value No. 1/ Min.: 0 deg, Max.: 124.5 deg | - | No |
| Diagnostic Note: This is the value of accelerator pedal position sensor No. 1 learned when the accelerator pedal is released. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Accel Fully Close Learn #2 | Accelerator fully released learned value No. 2/ Min.: 0 deg, Max.: 124.5 deg | - | No |
| Diagnostic Note: This is the value of accelerator pedal position sensor No. 2 learned when the accelerator pedal is released. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Throttle Sensor Volt % | Absolute throttle position sensor/ Min.: 0%, Max.: 100% |
| Yes |
| Diagnostic Note: The throttle position sensor No. 1 output is converted using 5 V = 100%.
| |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Throttl Sensor #2 Volt % | Throttle sensor position #2/ Min.: 0%, Max.: 100% |
| Yes |
| Diagnostic Note: The throttle position sensor No. 2 output is converted using 5 V = 100%. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| ST1 | Brake pedal signal/ ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released | No |
| Diagnostic Note: This is the stop light switch signal. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| System Guard | System guard/ ON or OFF | ON | No |
| Diagnostic Note: When there is a difference between the target and actual throttle valve opening angles, system guard turns off and stops the electronic throttle control system function. OFF: Electronic throttle control is stopped. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Open Side Malfunction | Open malfunction/ ON or OFF | OFF | No |
| Diagnostic Note: This parameter indicates a malfunction in the electronic throttle when the throttle valve is open. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Throttle Idle Position | Whether or not throttle position sensor detecting idle/ ON or OFF | - | No |
| Diagnostic Note: This is a parameter calculated by the ECM. The value is ON when the throttle is at the idle position and OFF when the throttle is open. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Throttle Require Position | Required throttle position/ Min.: 0 V, Max.: 4.98 V | - | No |
| Diagnostic Note: This is a value calculated by the ECM showing the voltage for the target throttle valve position. It is almost an exact match of the Throttle Position No. 1 value except during very rapid throttle valve movement, such as that used during wheelspin control. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Throttle Sensor Position | Throttle sensor position/ Min.: 0%, Max.: 100% |
| Yes |
| Diagnostic Note: This is the throttle valve opening amount used for engine control. (100% signifies 125° of throttle valve rotation. This does not include the amount the throttle valve is opened to maintain the idling speed during idling.) This value has no meaning when the ignition switch is ON and the engine is stopped. The throttle valve opening amount during idling is indicated by 0%. When the throttle valve is fully open, the value is 68%. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Throttle Position No. 1 | Throttle position sensor No. 1 output voltage/ Min.: 0 V, Max.: 4.98 V | Almost same as "Throttle Require Position"
| No |
| Diagnostic Note: This is the throttle position sensor No. 1 output voltage. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Throttle Position No. 2 | Throttle position sensor No. 2 output voltage/ Min.: 0 V, Max.: 4.98 V |
| No |
| Diagnostic Note: This is the throttle position sensor No. 2 output voltage. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Throttle Position Command | Throttle position command value/ Min.: 0 V, Max.: 4.98 V | - | No |
| Diagnostic Note: Throttle Position Command is the same value as Throttle Require Position. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Throttle Sens Open Pos #1 | Throttle position sensor No. 1/ Min.: 0 V, Max.: 4.98 V | 0.6 to 0.9 V | No |
| Diagnostic Note: This is the throttle position sensor No. 1 output voltage when there is no current supplied to the electronic throttle actuator. The accelerator pedal is released but the throttle valve is kept open by the throttle valve opener with the ignition switch ON. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Throttle Sens Open Pos #2 | Throttle position sensor No. 2/ Min.: 0 V, Max.: 4.98 V | 2.2 to 2.6 V | No |
| Diagnostic Note: This is the throttle position sensor No. 2 output voltage when there is no current supplied to the electronic throttle actuator. The accelerator pedal is released but the throttle valve is kept open by the throttle valve opener with the ignition switch ON. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Throttle Sens Open #1 (AD) | Throttle sensor opener position No. 1 (AD)/ Min.: 0 V, Max.: 4.9 V | 0.6 to 0.9 V | No |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Throttle Motor | Whether or not throttle motor control is permitted/ ON or OFF | Idling: ON | No |
| Diagnostic Note: Read the value with the ignition switch ON (Do not start engine) | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Throttle Motor Current | Throttle actuator current/ Min.: 0 A, Max.: 19.9 A | 0 to 3.0 A: Idling | No |
Diagnostic Note:
| |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Throttle Motor DUTY | Throttle actuator/ Min.: 0%, Max.: 100% | 10 to 22%: Idling | Yes |
| Diagnostic Note: This is the output duty ratio of the throttle actuator drive circuit. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Throttle Motor Duty (Open) | Throttle actuator duty ratio (open)/ Min.: 0%, Max.: 255% | 0 to 40%: Idling | No |
Diagnostic Note:
| |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Throttle Motor Duty (Close) | Throttle actuator duty ratio (close)/ Min.: 0%, Max.: 255% | 0 to 40%: Idling | No |
| Diagnostic Note: This is the duty ratio used to drive the throttle actuator and close the throttle valve. It is an ECM command signal.
| |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Throttle Fully Close Learn | Throttle valve fully closed position (learned value)/ Min.: 0 V, Max.: 4.98 V | 0.4 to 1.0 V: Accelerator pedal released | No |
Diagnostic Note:
| |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| ETCS Actuator Power | Whether or not electric throttle control system power is input/ ON or OFF | Idling: ON | No |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| +BM Voltage | +BM voltage/ Min.: 0 V, Max.: 79.998 V | 11 to 14 V: Ignition switch ON and system normal | No |
| Diagnostic Note: This is the power supply for the electronic throttle actuator. When the power supply is interrupted for approximately 1 second, DTCs P2118 (open circuit) and P0657 (short circuit, ECU malfunction) are stored and the electronic throttle control system enters fail-safe mode (normal operation is not restored until the ignition switch is turned off). | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Actuator Power Supply | Actuator power supply/ ON or OFF | ON: Idling | No |
| Diagnostic Note: If +BM power is lost, this item changes to OFF. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Fail Safe Drive | Whether or not fail-safe function is executed/ ON or OFF | ETCS has failed: ON | No |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Fail Safe Drive (Main CPU) | Whether or not fail-safe function is executed/ ON or OFF | ETCS has failed: ON | No |
| Fuel System (Ptrl General) |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Injector (Port) | Injection period of the No. 1 cylinder/ Min.: 0 μs, Max.: 65535 μs | - | Yes |
| Diagnostic Note: This is the injection period of the No. 1 cylinder (the command value from the ECM). | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Injection Volum (Cylinder 1) | Injection volume (cylinder 1)/ Min.: 0 ml, Max.: 2.047 ml | 0 to 0.5 ml | Yes |
| Diagnostic Note: This is the fuel injection volume for 10 injections. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Fuel Pump/Speed Status | Fuel pump status/ ON or OFF | ON: Starter on or engine running | Yes |
| EVAP System (Ptrl Evaporative) |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Evap Purge Flow | Purge flow/ Min.: 0%, Max.: 399.9% | - | Yes |
| Diagnostic Note: This is the percentage of total engine airflow contributed by EVAP purge operation. (Evap Purge Flow = Purge flow / Engine airflow x 100 (%)) It is based on MAF and a stored value for airflow and controlled by adjusting the duty cycle for the purge VSV. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Purge Density Learn Value | Purge density learned value/ Min.: -200, Max.: 199.993 | - | Yes |
| Diagnostic Note: Purge Density Learn Value is the proportion of the decrease in injection volume (based on the change in the air-fuel ratio feedback compensation value) related to a 1% purge flow rate. When Purge Density Learn Value is a large negative value, the purge effect is large. The purge density is determined from the change in the air-fuel ratio feedback compensation value when purge flow is introduced. Purge density learning is performed so that the feedback compensation value is 0 +/-2%.
| |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| EVAP Purge VSV | VSV status for EVAP control/ ON or OFF | - | Yes |
| Diagnostic Note: This parameter displays ON when the VSV duty ratio is 30% or more, and displays OFF when the VSV duty ratio is less than 30%. | |||
| Air Fuel Ratio Control 1 (All Data) |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Target Air-Fuel Ratio | Target air fuel ratio/ Min.: 0, Max.: 1.99 | 0.8 to 1.2: During idling | Yes |
| Diagnostic Note: This is the target air-fuel ratio used by the ECM.
| |||
| Air Fuel Ratio Control 2 (Ptrl AF O2 Sensor) |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| O2S B1S1 | Heated oxygen sensor output voltage for Bank 1 Sensor 1/ Min.: 0 V, Max.: 1.275 V | 0 to 1 V | Yes |
| Diagnostic Note: This is the output voltage of the heated oxygen sensor.
Results of real-vehicle check when performing the Active Test: Injection Volume: -12.5%
| |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Short FT #1 | Short-term fuel trim for bank 1/ Min.: -100%, Max.: 99.2% | -20 to 20% | Yes |
| Diagnostic Note: This item is the "short-term fuel injection volume compensation ratio" used to maintain the air fuel ratio at the stoichiometric ratio using the heated oxygen sensor for feedback. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Long FT #1 | Long-term fuel trim for bank 1/ Min.: -100%, Max.: 99.2% | -20 to 20% | Yes |
| Diagnostic Note: The ECM will learn the Long FT values based on Short FT. The goal is to keep Short FT at 0% to keep the A/F mixture at the stoichiometric ratio. This value is used to determine whether the air-fuel ratio control system is malfunctioning. The condition of the system is determined based on the sum of Short FT and Long FT (excluding times when the system is in transition).
| |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Fuel System Status #1 | Fuel system status for bank 1/ OL, CL, OL Drive, OL Fault or CL Fault | CL: Idling after warming up | Yes |
Diagnostic Note:
| |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| O2FT B1S1 | Short-term fuel trim associated with bank 1 sensor 1/ Min.: -100%, Max.: 99.2% | -20 to 20% | Yes |
| Diagnostic Note: This item is the "short-term fuel injection volume compensation ratio" used to maintain the air fuel ratio at the stoichiometric ratio using the heated oxygen sensor for feedback. | |||
| Ignition System (Ignition) |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| IGN Advance | Ignition timing advance for No. 1 cylinder/ Min.: -64 deg., Max.: 63.5 deg. | BTDC 0 to 20 deg.: Idling | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Knock Feedback Value | Knocking feedback value/ Min.: -1024° CA, Max.: 1023.9° CA | - | Yes |
| Diagnostic Note: This is the ignition timing retard compensation amount determined by the presence or absence of knocking. Ignition timing = Most retarded timing value*1 + Knock Correct Learn Value*2 + Knock Feedback Value*3 + each compensation amount Example: 21°CA = 10° + 14° - 3° *1: The most retarded timing value is a constant determined by the engine speed and engine load. *2: The knock correction learned value is calculated as shown below in order to keep Knock Feedback Value as close to -3°CA as possible. When Knock Feedback Value is less than -4°CA, Knock Correct Learn Value is slowly decreased. When Knock Feedback Value is more than -2°CA, Knock Correct Learn Value is slowly increased. *3: The base value is -3°CA and is adjusted based on the presence or absence of knocking. When there is no knocking, the value is increased, and when knocking is present, the value is decreased.
Possible Causes:
| |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Knock Correct Learn Value | Knocking correction learned value/ Min.: -1024° CA, Max.: 1023.9° CA | - | Yes |
| Diagnostic Note: Refer to "Knock Feedback Value". When there is knocking or a lack of power, compare the following values to another vehicle of the same model.
Knock Correct Learn Value is small: Knocking is present and the ignition timing is being retarded.
| |||
| VVT Control (Ptrl Valve Control) |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| VVT Control Status #1 | Variable Valve Timing (VVT) control status for bank 1/ ON or OFF | - | Yes |
| Diagnostic Note: ON: The ECM is sending commands to change the timing (even when the timing is advanced, when the timing is being maintained and not being retarded or advanced any further, the value changes to OFF). OFF: The system is commanding the timing to change to the most retarded timing. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| VVT Aim Angle #1 | VVT hold duty learned value for bank 1/ Min.: 0%, Max.: 100% | - | No |
| Diagnostic Note: This value represents the duty ratio necessary to operate the camshaft timing oil control valve in order to block the camshaft timing oil control valve path and maintain the advanced state of the camshaft timing gear. This is only available during the Active Test. Refer to "VVT OCV Duty #1". | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| VVT Change Angle #1 | VVT displacement angle for bank 1/ Min.: 0 DegFR, Max.: 639.9 DegFR | - | No |
| Diagnostic Note: This is the VVT displacement angle during forced operation. This is only available during the Active Test. By checking VVT Change Angle during the Active Test, it is also possible to determine whether or not the camshaft position sensor signal is being output. Refer to "VVT OCV Duty #1". | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| VVT OCV Duty #1 | VVT camshaft timing oil control valve operation duty for bank 1/ Min.: 0%, Max.: 100% | - | No |
| Diagnostic Note: This is the requested duty value for forced operation. This is only available during the Active Test. Results of the real-vehicle check when performing the Control the VVT Linear (Bank 1) Active Test: VVT OCV Duty #1 = 0%, VVT Change Angle #1 = 0 DegFR ↓ VVT OCV Duty #1 = 30%, VVT Change Angle #1 = 0 DegFR ↓ VVT OCV Duty #1 = 70%, VVT Change Angle #1 = 39.0 DegFR ↓ VVT OCV Duty #1 = 100%, VVT Change Angle #1 = 39.0 DegFR ↓ VVT OCV Duty #1 = 32%, VVT Change Angle #1 = 0 DegFR After the above test, VVT Aim Angle #1 = 26.6%. | |||
| Various Vehicle Conditions 2 (All Data) |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Starter Signal | Starter signal/ Open or Close | Open: Starter operating Close: Starter not operating | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Power Steering Signal | Power steering switch signal/ ON or OFF | ON: Power steering operating | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Power Steer. Sig. Record | Power steering switch signal/ ON or OFF | ON: When steering wheel is first turned after ignition switch is turned to ON | Yes |
| Diagnostic Note: This signal status usually ON until ignition switch turned to OFF | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Neutral Position SW Signal | Park/neutral position switch status/ ON or OFF | ON: Shift lever in P or N | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Stop Light Switch | Stop light switch/ ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| A/C Signal | A/C status/ ON or OFF | ON: A/C on | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Closed Throttle Position SW | Closed throttle position switch/ ON or OFF |
| Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Electrical Load Signal | Electrical load signal/ ON or OFF | ON: Headlights or defogger is turned ON | Yes |
| Check Mode (Check Mode) |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note | Stored as Freeze Frame Data |
| Check Mode | Check mode/ ON or OFF | ON: Check mode on | Refer to Check Mode Procedure (Click here). | No |
| SPD Test Result | Check mode result for vehicle speed sensor/ Compl or Incmpl | - | - | No |
| Various Vehicle Conditions 3 (All Data) |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| # Codes (Include History) | Number of codes/ Min.: 0, Max.: 255 | 0 | No |
| Diagnostic Note: This is the number of DTCs stored. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| MIL | MIL status/ ON or OFF | OFF | No |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Time after DTC Cleared | Time after DTCs cleared/ Min.: 0 minutes, Max.: 65535 minutes | Time after DTCs cleared | Yes |
| Diagnostic Note: This is the time elapsed after DTCs were cleared (or after the vehicle left the factory). Time elapsed after the ignition switch is turned off is not counted. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Distance from DTC Cleared | Distance driven after DTCs cleared/ Min.: 0 km, Max.: 65535 km | Distance driven after DTCs cleared | Yes |
| Diagnostic Note: This is the distance driven after DTCs were cleared (or after the vehicle left the factory). | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Warmup Cycle Cleared DTC | Warmup cycles after DTCs cleared/ Min.: 0, Max.: 255 | - | Yes |
| Diagnostic Note: This is the number of warmup cycles after the DTCs were cleared. This is the number of times the engine was warmed up* after DTCs were cleared (or after the vehicle left the factory). *: An engine warmup is defined as the engine coolant temperature rising 20°C (36°F) or more and reaching a temperature of 70°C (158°F) or higher after the engine is started. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| OBD Requirements | OBD requirement | Not OBD compliant | No |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Number of Emission DTC | Emissions-related DTCs | - | No |
| Diagnostic Note: This is the number of emissions-related DTCs. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| TC and TE1 | TC and CG (TE1) terminals of DLC3/ ON or OFF | - | Yes |
| Various Vehicle Conditions 4 (All Data) |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| ACT VSV | A/C cut status/ ON or OFF | - | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Idle Fuel Cut | Fuel cut at idle/ ON or OFF | ON: Fuel cut operating | Yes |
| Diagnostic Note: Idle Fuel Cut = "ON" when the throttle valve is fully closed and the engine speed is high. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| FC TAU | Fuel cut TAU (fuel cut during very light load)/ ON or OFF | ON: Fuel cut operating | Yes |
| Diagnostic Note: This is the fuel cut performed under a very light load to prevent the engine combustion from becoming incomplete. | |||
| Various Vehicle Conditions 5 (Vehicle Information) |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Model Code | Model code | - | No |
| Diagnostic Note: Used for identifying the model code: TGN### | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Engine Type | Engine type | - | No |
| Diagnostic Note: Used for identifying the engine type: 2TRFE | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Cylinder Number | Number of cylinders/ Min.: 0, Max.: 255 | - | No |
| Diagnostic Note: Used for identifying the number of cylinders: 4 | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Transmission Type | Transmission type | - | No |
| Diagnostic Note: Used for identifying the transmission type: MT, ECT 4th | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Destination | Destination | - | No |
| Diagnostic Note: Used for identifying the destination: W | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Model Year | Model year/ Min.: 1900, Max.: 2155 | - | No |
| Diagnostic Note: Used for identifying the model year: 20## | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| System Identification | System identification | - | No |
| Diagnostic Note: Used for identifying the engine system: Gasoline (gasoline engine) | |||
| Automatic Transmission 1 (All Data) |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| SPD (NC0) | Input turbine speed/ Min.: 0 rpm, Max.: 12750 rpm |
| Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| SPD (SP2) | Output shaft speed/ Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed) | Yes |
| Automatic Transmission 2 (AT) |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Shift SW Status (R Range) | Park/neutral position switch status/ ON or OFF |
| Yes |
| Diagnostic Note: When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
| |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Shift SW Status (2 Range) | Park/neutral position switch status/ ON or OFF |
| Yes |
| Diagnostic Note: When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
| |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Shift SW Status (L Range) | Park/neutral position switch status/ ON or OFF |
| Yes |
| Diagnostic Note: When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
| |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Shift SW Status (3 Range) | Park/neutral position switch status/ ON or OFF |
| Yes |
| Diagnostic Note: When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
| |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| A/T Oil Temperature 3 | No. 3 ATF temperature sensor value/ Min.: -40°C, Max.: 215°C |
| Yes |
| Diagnostic Note: If the value is -40°C (-40°F) or 215°C (419°F), the No. 3 ATF temperature sensor circuit is open or shorted. | |||
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Lock Up Solenoid Status | Lock-up solenoid status/ ON or OFF | Lock-up solenoid is:
| Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| Shift Status | ECM gear shift command/ 1st, 2nd, 3rd or 4th | Shift lever in D: 1st, 2nd, 3rd or 4th | Yes |
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
| SLT Solenoid Status | Shift solenoid SLT status/ ON or OFF |
| Yes |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the intelligent tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Injection Volume | Change injection volume | Between -12.5% and 24.8% |
|
| Control the Injection Volume for A/F Sensor | Change injection volume | -12.5%, 0% or +12.5% |
|
| Activate the VSV for Evap Control | Activate purge VSV control | ON/OFF |
|
| Control the A/C Cut Signal | A/C compressor cut | ON/OFF | - |
| Control the Fuel Pump / Speed | Activate fuel pump | ON/OFF | Perform this test with the engine stopped. |
| Connect the TC and TE1 | Turn on and off TC and TE1 connection | ON/OFF |
|
| Control the Idle Fuel Cut Prohibit | Prohibit idling fuel cut control | ON/OFF | - |
| Control the ETCS Open/Close Slow Speed | Throttle actuator | Close/Open Open: Throttle valve opens slowly | This test is possible when the following conditions are met:
|
| Control the ETCS Open/Close Fast Speed | Throttle actuator | Close/Open Open: Throttle valve opens quickly |
|
| Control the VVT Linear (Bank 1) | Control VVT (for intake side of bank 1) | -128 to 127% (This value added to present camshaft timing oil control valve control duty) 100%: Maximum advance -100%: Maximum retard |
|
| Control the VVT System (Bank 1) | Turn camshaft timing oil control valve on and off | ON/OFF ON: VVT OCV Duty #1 100% |
|
| Control the Cylinder #1 Fuel Cut | Cylinder #1 injector fuel cut | ON/OFF | Test is possible while the vehicle is stopped and the engine is idling. |
| Control the Cylinder #2 Fuel Cut | Cylinder #2 injector fuel cut | ON/OFF | Test is possible while the vehicle is stopped and the engine is idling. |
| Control the Cylinder #3 Fuel Cut | Cylinder #3 injector fuel cut | ON/OFF | Test is possible while the vehicle is stopped and the engine is idling. |
| Control the Cylinder #4 Fuel Cut | Cylinder #4 injector fuel cut | ON/OFF | Test is possible while the vehicle is stopped and the engine is idling. |
| Control the All Cylinders Fuel Cut | Fuel cut for all cylinders | ON/OFF | Test possible while the vehicle is stopped and the engine is idling. |

| Tester Display | Measurement Item/Range | Normal Condition | |
| Control the Injection Volume for A/F Sensor | - | ▲A | ▲B |
| Active Test operation | -12.5% | +12.5% | |
| O2S B1S1 | 0.03 V | 0.85 V | |

| Tester Display | Measurement Item/Range | Normal Condition | |
| Control the ETCS Open/Close Fast Speed | - | ▲A | ▲B |
| Active Test operation | Close | Open | |
| Throttle Position Command | 2.597 V | 0.742 V | |
| Throttle Position No. 1 | 2.597 V | 0.742 V | |
| Throttle Motor Duty (Open) | 14% | 0% | |
| Throttle Motor Duty (Close) | 0% | 10% | |

| Tester Display | Measurement Item/Range | Normal Condition | |
| Activate the VSV for Evap Control | - | ▲A | ▲B |
| Active Test operation | ON | OFF | |
| EVAP Purge VSV | ON | OFF | |
| Short FT #1 | -1.563% | 0.000% | |
| Injection (Port) | 2288.0 μs | 2430.0 μs | |
| O2S B1S1 | 0.85 V | 0.03 V | |

| Tester Display | Measurement Item/Range | Normal Condition | |
| Control the VVT Linear (Bank 1) | - | ▲A | ▲B |
| Active Test operation* | +20% | -20% | |
| VVT Change Angle #1 | 54.9 DegFR | 0.0 DegFR | |
| VVT OCV Duty #1 | 53.9% | 13.9% | |
| VVT Aim Angle #1 | 33.9% | 33.9% | |