Home › ENGINE · 1KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM

ECD SYSTEM > ECM Power Source Circuit

for Preparation Click here


DESCRIPTION

When the ignition switch is turned ON, the battery voltage is applied to terminal IGSW of the ECM. The ECM "MREL" output signal causes a current to flow to the coil, closing the contacts of the MAIN relay and supplying power to terminal +B of the ECM.

WIRING DIAGRAM


A265477E01


INSPECTION PROCEDURE

NOTICE:
If the ECM is replaced, the new ECM needs initialization (Click here).

1.CHECK ECM (+B VOLTAGE)


    A018294E59
  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connectors.

    Standard voltage:
    Tester Connection
    Specified Condition
    E4-1 (+B) - E6-7 (E1)
    9 to 14 V



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


2.CHECK WIRE HARNESS (ECM - BODY GROUND)


    A065745E14
  1. Disconnect the E6 ECM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E6-7 (E1) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3.CHECK ECM (IGSW VOLTAGE)


    A018294E60
  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connectors.

    Standard voltage:
    Tester Connection
    Specified Condition
    E4-9 (IGSW) - E6-7 (E1)
    9 to 14 V



OK
Go to step 6
NG


4.INSPECT FUSE (IGN FUSE)


    A155929E02
  1. Remove the IGN fuse from the instrument panel junction block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
CHECK FOR SHORT IN ALL HARNESS AND COMPONENTS CONNECTED TO FUSE, AND REPLACE FUSE
OK


5.INSPECT IGNITION SWITCH ASSEMBLY


    A056879E62
  1. Disconnect the I8 ignition switch connector.

  1. Measure the resistance of the ignition switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (AM2) - 6 (IG2)
    LOCK
    10 kΩ or higher
    5 (AM2) - 6 (IG2)
    ON
    Below 1 Ω



NG
REPLACE IGNITION SWITCH ASSEMBLY
OK


6.CHECK ECM (MREL VOLTAGE)


    A018294E61
  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connectors.

    Standard voltage:
    Tester Connection
    Specified Condition
    E4-8 (MREL) - E6-7 (E1)
    9 to 14 V



NG
REPLACE ECM
OK


7.INSPECT FUSE (EFI FUSE)


    A099789E11
  1. Remove the EFI fuse from the engine room junction block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
CHECK FOR SHORT IN ALL HARNESS AND COMPONENTS CONNECTED TO FUSE, AND REPLACE FUSE
OK


8.INSPECT INTEGRATION NO.1 RELAY (MAIN RELAY)


    G039047E14
  1. Remove the integration relay from the engine room junction block (Click here).

  1. Measure the voltage of the MAIN relay.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    1J-4 - Body ground
    Ignition switch ON
    10 to 14 V



NG
REPLACE INTEGRATION NO.1 RELAY
OK


9.CHECK WIRE HARNESS (INTEGRATION RELAY (MAIN RELAY) - ECM)


    G034918E12
  1. Disconnect the 1J integration relay connector from the engine room junction block (Click here).

  1. Disconnect the E4 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    1J-4 - E4-1 (+B)
    Below 1 Ω
    1J-4 or E4-1 (+B) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR (INTEGRATION RELAY (MAIN RELAY) - ECM)
OK

REPAIR OR REPLACE HARNESS AND CONNECTOR (+B TERMINAL OF ECM - BATTERY POSITIVE TERMINAL)