ECD SYSTEM > TERMINALS OF ECM |

| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| BATT (E23-1) - E1 (E20-14) | L - BR | Battery (for measuring the battery voltage and for ECM memory) | Always | 9 to 14 V |
| SREL (E23-2) - E01 (E20-13) | R - W-B | GLOW relay | Cranking | 9 to 14 V |
| SREL (E23-2) - E01 (E20-13) | R - W-B | GLOW relay | Idling (engine started and 600 sec. have passed) | 0 to 1.5 V |
| MREL (E23-3) - E1 (E20-14) | W-G - BR | MAIN relay | Ignition switch ON | 9 to 14 V |
| MREL (E23-3) - E1 (E20-14) | W-G - BR | MAIN relay | Ignition switch OFF (after ignition switch OFF for 2 sec.) | 0 to 1.5 V |
| TC (E23-4) - E1 (E20-14) | P-B - BR | Terminal TC of DLC3 | Ignition switch ON | 9 to 14 V |
| W (E23-5) - E1 (E20-14) | R-B - BR | MIL | MIL lights up | 0 to 3 V |
| W (E23-5) - E1 (E20-14) | R-B - BR | MIL | MIL does not light up | 9 to 14 V |
| THWO (E23-8) - E1 (E20-14) | P - BR | Combination meter | Ignition switch ON | Pulse generation (See waveform 1) |
| SP1 (E23-9) - E1 (E20-14) | V-R - BR | Speed signal from combination meter | Ignition switch ON, rotate driving wheel slowly | Pulse generation (See waveform 2) |
| STA (E23-11) - E1 (E20-14) | L-Y - BR | Starter signal | Cranking | 6 V or more |
| +B (E23-12) - E1 (E20-14) | B - BR | Power source of ECM | Ignition switch ON | 9 to 14 V |
| IGSW (E23-14) - E1 (E20-14) | B-O - BR | Ignition switch | Ignition switch ON | 9 to 14 V |
| SIL (E23-15) - E1 (E20-14) | R-Y - BR | Terminal SIL of DLC3 | Connect intelligent tester to DLC3 | Pulse generation |
| STP (E23-19) - E1 (E20-14) | G-W - BR | Stop light switch | Brake pedal depressed | 9 to 14 V |
| STP (E23-19) - E1 (E20-14) | G-W - BR | Stop light switch | Brake pedal released | Below 1.5 V |
| GIND (E25-1) - E1 (E20-14) | Y-R - BR | Glow indicator light | Glow indicator light lights up | 0 to 3 V |
| GIND (E25-1) - E1 (E20-14) | Y-R - BR | Glow indicator light | Glow indicator light does not light up | 9 to 14 V |
| AC1 (E25-2) - E1 (E20-14) | Y - BR | A/C amplifier | A/C switch ON (magnetic clutch ON) | Below 1.5 V |
| AC1 (E25-2) - E1 (E20-14) | Y - BR | A/C amplifier | A/C switch OFF | 7.5 to 14 V |
| ACT (E25-8) - E1 (E20-14) | R-L - BR | A/C amplifier | Ignition switch ON | 9 to 14 V |
| ACT (E25-8) - E1 (E20-14) | R-L - BR | A/C amplifier | A/C cut controlled (driving below 30 km/h (18.6 mph), accelerator pedal fully depressed for 5 sec.) | 0 to 3 V |
| VPA (E25-5) - EPA (E25-4) | W-L - BR-W | Accelerator pedal position sensor (for engine control) | Ignition switch ON, accelerator pedal released | 0.5 to 1.1 V |
| VPA (E25-5) - EPA (E25-4) | W-L - BR-W | Accelerator pedal position sensor (for engine control) | Ignition switch ON, accelerator pedal depressed | 2.6 to 4.5 V |
| VPA2 (E25-12) - EPA (E25-4) | GR-G - BR-W | Accelerator pedal position sensor (for sensor malfunction detection) | Ignition switch ON, accelerator pedal released | 1.2 to 2.0 V |
| VPA2 (E25-12) - EPA (E25-4) | GR-G - BR-W | Accelerator pedal position sensor (for sensor malfunction detection) | Ignition switch ON, accelerator pedal depressed | 3.4 to 5.3 V |
| VCPA (E25-6) - EPA (E25-4) | LG-R - BR-W | Power source of accelerator pedal position sensor (for VPA) | Ignition switch ON | 4.5 to 5.5 V |
| TACH (E25-7) - E1 (E20-14) | B-W - BR | Engine speed | Idling | Pulse generation (See waveform 3) |
| ST1- (E25-11) - E1 (E20-14) | R-L - BR | Stop light switch | Brake pedal depressed | Below 1.5 V |
| ST1- (E25-11) - E1 (E20-14) | R-L - BR | Stop light switch | Brake pedal released | 9 to 14 V |
| VC (E21-1) - E2 (E21-9) | R-W - BR | Power source of sensor (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| PIM (E21-2) - E2 (E21-9) | L-B - BR | Manifold absolute pressure sensor | Apply vacuum 60 kPa (450 mmHg, 17.7 in.Hg) | 0.2 to 0.8 V |
| PIM (E21-2) - E2 (E21-9) | L-B - BR | Manifold absolute pressure sensor | Apply vacuum 207 kPa (1,550 mmHg, 61.0 in.Hg) | 4.2 to 4.8 V |
| THA (E21-3) - E2 (E21-9) | Y-G - BR | Intake air temperature sensor | Idling, air intake temp. 0°C (32°F) to 80°C (176°F) | 0.5 to 3.4 V |
| THW (E21-4) - E2 (E21-9) | R-L - BR | Engine coolant temperature sensor | Idling, engine coolant temp. 60°C (140°F) to 120°C (248°F) | 0.2 to 1.0 V |
| THF (E21-5) - E2 (E21-9) | G-B - BR | Fuel temperature sensor | Ignition switch ON (engine cold) | 0.5 to 3.4 V |
| DATA (E21-6) - E1 (E20-14) | Y - BR | Injection pump | For 0.5 sec. after ignition switch ON | Pulse generation |
| CLK (E21-14) - E1 (E20-14) | L - BR | Injection pump | For 0.5 sec. after ignition switch ON | Pulse generation |
| THOP (E21-15) - E1 (E20-14) | GR - BR | Throttle open switch | Idling (engine warmed up) | 9 to 14 V |
| THOP (E21-15) - E1 (E20-14) | GR - BR | Throttle open switch | Ignition switch ON (once within 5 sec.) | 0 to 3 V |
| LU-B (E20-7) - E01 (E20-13) | L-Y - W-B | Throttle control motor (Intake shutter) | Racing (engine warmed up) | Pulse generation (See waveform 4) |
| LU+B (E20-8) - E01 (E20-13) | L-R - W-B | Throttle control motor (Intake shutter) | Racing (engine warmed up) | Pulse generation (See waveform 4) |
| LU-A (E20-9) - E01 (E20-13) | L-W - W-B | Throttle control motor (Intake shutter) | Racing (engine warmed up) | Pulse generation (See waveform 4) |
| LU+A (E20-10) - E01 (E20-13) | L-B - W-B | Throttle control motor (Intake shutter) | Racing (engine warmed up) | Pulse generation (See waveform 4) |
| TCV (E20-11) - E01 (E20-13) | R-W - W-B | Timing control valve | Ignition switch ON | 9 to 14 V |
| TCV (E20-11) - E01 (E20-13) | R-W - W-B | Timing control valve | Idling | Pulse generation (See waveform 5) |
| SPV+ (E20-12) - E1 (E20-14) | R-L - BR | Spill control valve | Ignition switch ON | 9 to 14 V |
| SPV+ (E20-12) - E1 (E20-14) | R-L - BR | Spill control valve | Idling | Pulse generation |
| SPV- (E20-25) - E1 (E20-14) | R-Y - BR | Spill control valve | Idling | Pulse generation (See waveform 7) |
| TDC+ (E20-17) - TDC- (E20-16) | R - G | Crankshaft position sensor | Idling | Pulse generation (See waveform 6) |
| NE+ (E20-19) - NE- (E20-18) | L - Y | Engine speed sensor | Idling | Pulse generation (See waveform 6) |
| Waveform 1 (Reference): |
![]() |
A/C amplifier signal.
| Item | Content |
| Symbols (Terminal No.) | THWO (E23-8) - E1 (E20-14) |
| Tool Setting | 5 V/DIV., 0.1 sec./DIV. |
| Condition | During idling |
| Waveform 2 (Reference): |
![]() |
Speed signal.
| Item | Content |
| Symbols (Terminal No.) | SP1 (E23-9) - E1 (E20-14) |
| Tool Setting | 2 V/DIV., 20 msec./DIV. |
| Condition | When driving at approx. 20 km/h (12.4 mph). |
| Waveform 3 (Reference): |
![]() |
Engine speed signal.
| Item | Content |
| Symbols (Terminal No.) | TACH (E25-7) - E1 (E20-14) |
| Tool Setting | 5 V/DIV., 20 msec./DIV. |
| Condition | During idling after warming up |
| Waveform 4 (Reference): |
![]() |
Throttle control motor signal.
| Item | Content |
| Symbols (Terminal No.) | LU+A (E20-10) - E01 (E20-13) LU+B (E20-8) - E01 (E20-13) LU-A (E20-9) - E01 (E20-13) LU-B (E20-7) - E01 (E20-13) |
| Tool Setting | 10 V/DIV., 0.5 msec./DIV. |
| Condition | During engine racing |
| Waveform 5 (Reference): |
![]() |
Timing control value signal.
| Item | Content |
| Symbols (Terminal No.) | TCV (E20-11) - E01 (E20-13) |
| Tool Setting | 10 V/DIV., 10 msec./DIV. |
| Condition | During idling |
| Waveform 6 (Reference): |
![]() |
Crankshaft position sensor and engine speed sensor signal.
| Item | Content |
| Symbols (Terminal No.) | TDC+ (E20-17) - TDC- (E20-16) NE+ (E20-19) - NE- (E20-18) |
| Tool Setting | 2 V/DIV., 20 msec./DIV. |
| Condition | During idling |
| Waveform 7 (Reference): |
![]() |
Spill control valve signal.
| Item | Content |
| Symbols (Terminal No.) | SPV- (E20-25) - E1 (E20-14) |
| Tool Setting | 20 V/DIV., 10 msec./DIV. |
| Condition | During idling |