ECD SYSTEM > DATA LIST / ACTIVE TEST |
| READ DATA LIST |
Warm up the engine.
Turn the ignition switch OFF.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Notes |
| Coolant Temp (COOLANT TEMP) | Engine coolant temperature/ Min.: -40°C, Max.: 215°C | 80 to 95°C (176 to 203°F): After warming up engine | If value -40°C or 140°C, sensor circuit open or shorted |
| PIM (PIM) | Absolute pressure inside intake manifold/ Min.: 0 kPa, Max.: 255 kPa |
| - |
| Engine SPD (ENGINE SPD) | Engine speed/ Min.: 0 rpm, Max.: 16383.75 rpm | 720 to 820 rpm: Idling (A/C off) After warming up engine | - |
| Vehicle SPD (VEHICLE SPD) | Vehicle speed/ Min.: 0 km/h, Max.: 255 km/h | Actual vehicle speed | Speed indicated on speedometer |
| Intake Air (INTAKE AIR) | Intake air temperature/ Min.: -40°C, Max.: 215°C | Equivalent to temperature at intake manifold | If value -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted |
| Injection Volume (INJ VOLUME) | Injection volume/ Min.: 0 mm3, Max.: 1279.98 mm3 | 3 to 11 mm3: Idling | - |
| Injection Timing (INJ TIMING) | Injection timing/ Min.: 0 CA, Max.: 51 CA | 16 to 20 CA: Idling After warming up engine | - |
| Fuel Temp. (FUEL TEMP) | Fuel temperature status/ Min.: -40°C, Max.: 215°C | Actual fuel temperature | If value -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted |
| Accel Position (ACCEL POSITION) | Accelerator position status/ Min.: 0%, Max.: 100% |
| Read value with ignition switch ON (Do not start engine) |
| Throttle Step POS (THROTTLE POS) | Throttle step position/ Min.: 1 step, Max.: 255 step |
| Read value with ignition switch ON (Do not start engine) |
| #Codes (#CODES) | Number of memorized DTC codes/ Min.: 0, Max.: 255 | 0 | - |
| Stop Light SW (STOP LIGHT SW) | Stop light switch/ ON or OFF |
| - |
| A/C SIG (A/C SIGNAL) | A/C signal/ ON or OFF | ON: A/C switch is turned ON | - |
| Starter SIG (STARTER SIG) | Starter signal/ ON or OFF | ON: Cranking | - |
| Accel Open SW (ACCEL OPEN SW) | Accelerator pedal open switch/ ON or OFF | OFF: Accelerator pedal released | - |
| SPD Test (SPD Test) | Check mode result for vehicle speed sensor/ 0: COMPL, 1: INCOMPL | - | Click here
|
| Check Mode (CHECK MODE) | Check mode/ ON or OFF | ON: Check mode ON | - |
| A/C Cut SIG (A/C CUT SIG) | A/C cut signal/ ON or OFF | ON: A/C compressor ON | - |
| PERFORM ACTIVE TEST |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
Perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Notes |
| A/C Cut Signal | Control A/C cut signal | ON/OFF | - |
| TC/TE1 | Turn ON and OFF TC and TE1 connection | ON/OFF |
|