Home › TRANSMISSION · A340E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM (for 2KD-FTV)

AUTOMATIC TRANSMISSION SYSTEM (for 2KD-FTV) > TERMINALS OF ECU

for Preparation Click here



CHECK TCM

C214981E14

HINT:
The standard voltage at each TCM terminal is shown in the table below.
In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to inspect. The standard voltage between the terminals is shown under "Specified Condition".
Use the illustration above as a reference for the TCM terminals.


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
T19-12 (NSW) - T19-1 (E1)
L-Y - BR
PNP switch signal
  1. Ignition switch ON
  2. Shift lever in P or N
Below 1 V
  1. Ignition switch ON
  2. Shift lever not in P or N
11 to 14 V
T38-9 (R) - T19-1 (E1)
R-Y - BR
R shift position switch signal
  1. Ignition switch ON
  2. Shift lever in R
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in R
Below 1 V
T38-8 (D) - T19-1 (E1)
G-Y - BR
D shift position switch signal
  1. Ignition switch ON
  2. Shift lever in D or 3
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in D or 3
Below 1 V
T38-12 (3) - T19-1 (E1)
G-O - BR
3 shift position switch signal
  1. Ignition switch ON
  2. Shift lever in 3
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in 3
Below 1 V
T38-11 (2) - T19-1 (E1)
L - BR
2 shift position switch signal
  1. Ignition switch ON
  2. Shift lever in 2
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in 2
Below 1 V
T38-10 (L) - T19-1 (E1)
G-R - BR
L shift position switch signal
  1. Ignition switch ON
  2. Shift lever in L
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in L
Below 1 V
T19-18 (S1) - T19-1 (E1)
GR - BR
S1 solenoid signal
1st or 2nd gear
11 to 14 V
3rd or 4th gear
Below 1 V
T19-17 (S2) - T19-1 (E1)
W-L - BR
S2 solenoid signal
2nd or 3rd gear
11 to 14 V
1st or 4th gear
Below 1 V
T19-20 (SLT+) - T19-19 (SLT-)
G-Y - L-B
SLT solenoid signal
Engine idling
Pulse generation
T19-16 (SL) - T19-1 (E1)
G - BR
SL solenoid signal
Vehicle speed 65 km/h (40 mph), lock-up (ON to OFF)
Pulse generation
(See waveform 1)
Vehicle driving under look-up condition
11 to 14 V
T19-24 (THOC) - T19-23 (E2)
BR - B-Y
ATF temperature sensor signal
ATF temperature: 115°C (239°F) or higher
Below 1.5 V
T19-30 (SP2+) - T19-29 (SP2-)
R - G
Speed sensor SP2 signal
Vehicle speed 20 km/h (12 mph)
Pulse generation
(See waveform 2)
T19-3 (NC0+) - T19-2 (NC0-)
V - P
Speed sensor NC0 signal
Engine idling
(shift lever in P or N)
Pulse generation
(See waveform 3)
T37-25 (SPD1) - T19-1 (E1)
V-R - BR
Speed signal
Vehicle speed 20 km/h (12 mph)
Pulse generation
(See waveform 4)
T37-14 (STP) - T19-1 (E1)
G-W - BR
STP light switch signal
Brake pedal is depressed
7.5 to 14 V
Brake pedal is released
Below 1 V
T19-11 (STA) - T19-1 (E1)
B-Y - BR
Starter signal
Cranking
6 V or more
T37-6 (IG2) - T19-1 (E1)
B-O - BR
Ignition switch
Ignition switch ON
11 to 14 V
T37-21 (CAN+) - T19-1 (E1)
V - BR
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 5)
T37-20 (CAN-) - T19-1 (E1)
P - BR
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 6)


    C170572E01
  1. Using an oscilloscope, check waveform 1.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    T19-16 (SL) - T19-1 (E1)
    10 V/DIV., 100 msec./DIV.
    Vehicle speed 65 km/h (40 mph), lock-up (ON to OFF)



  2. C170571E02
  3. Using an oscilloscope, check waveform 2.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    T19-30 (SP2+) - T19-29 (SP2-)
    2 V/DIV., 20 msec./DIV.
    Vehicle speed 20 km/h (12 mph)



  4. C170570E01
  5. Using an oscilloscope, check waveform 3.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    T19-3 (NC0+) - T19-2 (NC0-)
    5 V/DIV., 0.5 msec./DIV.
    Engine idling (shift lever in P or N)



  6. C170574E01
  7. Using an oscilloscope, check waveform 4.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    T37-25 (SPD1) - T19-1 (E1)
    5 V/DIV., 20 msec./DIV.
    Vehicle speed 20 km/h (12 mph)



  8. C175015E01
  9. Using an oscilloscope, check waveform 5.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    T37-21 (CAN+) - T19-1 (E1)
    1 V/DIV., 10 μsec./DIV.
    Ignition switch ON



  10. C175016E01
  11. Using an oscilloscope, check waveform 6.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    T37-20 (CAN-) - T19-1 (E1)
    1 V/DIV., 10 μsec./DIV.
    Ignition switch ON


CHECK ECM

C115871E21

HINT:
The standard voltage at each ECM terminal is shown in the table below.
In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to inspect. The standard voltage between the terminals is shown under "Specified Condition".
Use the illustration above as a reference for the ECM terminals.


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E4-1 (+B) - E6-7 (E1)
B - BR
Power source of ECM
Ignition switch ON
11 to 14 V
E5-22 (CAN+) - E6-7 (E1)
V - BR
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 1)
E5-21 (CAN-) - E6-7 (E1)
P - BR
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 2)


    C175015E01
  1. Using an oscilloscope, check waveform 1.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    E5-22 (CAN+) - E6-7 (E1)
    1 V/DIV., 10 μsec./DIV.
    Ignition switch ON



  2. C175016E01
  3. Using an oscilloscope, check waveform 2.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    E5-21 (CAN-) - E6-7 (E1)
    1 V/DIV., 10 μsec./DIV.
    Ignition switch ON