AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV) > DATA LIST / ACTIVE TEST |
| READ DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / ECT / Data List.
According to the display on the tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Vehicle Speed | Vehicle speed/ Min.: 0 km/h (0 mph) Max.: 255 km/h (158 mph) | Actual vehicle speed | Speed indicated on speedometer |
| Engine Speed | Engine speed/ Min.: 0 rpm Max.: 16383.75 rpm | Engine idling: 700 to 800 rpm | - |
| Engine Run Time | Engine run time/ Min.: 0 seconds, Max.: 65535 seconds | Time after engine start | - |
| Battery Voltage | Battery voltage/ Min.: 0 V Max.: 65.535 V | Engine idling: 11 to 14 V | - |
| Starter Signal | Starter signal/ ON or OFF |
| - |
| Neutral Position SW Signal | PNP switch status/ ON or OFF |
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
|
| Stop Light Switch | Stop light switch status/ ON or OFF |
| - |
| Check Mode | Check mode/ ON or OFF | ON: Check mode ON | - |
| SPD Test Result | Check mode result for vehicle/ Compl or Incmpl | - | - |
| Complete Parts Monitor | Comprehensive component monitor/ Not Avl or Avail | - | - |
| Fuel System Monitor | Fuel system monitor/ Not Avl or Avail | - | - |
| Misfire Monitor | Misfire monitor/ Not Avl or Avail | - | - |
| EGR/VVT Monitor | EGR/VVT monitor/ Not Avl or Avail | - | - |
| EGR/VVT Monitor | EGR/VVT monitor/ Compl or Incmpl | - | - |
| O2S(A/FS) Heater Monitor | Heated oxygen sensor (air fuel ratio sensor) heater monitor/ Not Avl or Avail | - | - |
| O2S(A/FS) Heater Monitor | Heated oxygen sensor (air fuel ratio sensor) heater monitor/ Compl or Incmpl | - | - |
| O2S(A/FS) Monitor | Heated oxygen sensor (air fuel ratio sensor) monitor/ Not Avl or Avail | - | - |
| O2S(A/FS) Monitor | Heated oxygen sensor (air fuel ratio sensor) monitor/ Compl or Incmpl | - | - |
| A/C Monitor | A/C monitor/ Not Avl or Avail | - | - |
| A/C Monitor | A/C monitor/ Compl or Incmpl | - | - |
| 2nd Air Monitor | 2nd air monitor/ Not Avl or Avail | - | - |
| 2nd Air Monitor | 2nd air monitor/ Compl or Incmpl | - | - |
| EVAP Monitor | EVAP monitor/ Not Avl or Avail | - | - |
| EVAP Monitor | EVAP monitor/ Compl or Incmpl | - | - |
| Heated Catalyst Monitor | Heated catalyst monitor/ Not Avl or Avail | - | - |
| Heated Catalyst Monitor | Heated catalyst monitor/ Compl or Incmpl | - | - |
| Catalyst Monitor | Catalyst monitor/ Not Avl or Avail | - | - |
| Catalyst Monitor | Catalyst monitor/ Compl or Incmpl | - | - |
| # Codes (Include History) | Number of Codes/ Min.: 0 Max.: 255 | - | Number of detected DTCs |
| MIL | MIL status/ ON or OFF | ON: MIL ON | - |
| Time after DTC Cleared | Time after DTC cleared/ Min.: 0 minutes, Max.: 65535 minutes | Equivalent to time after DTCs cleared | - |
| Distance from DTC Cleared | Distance after DTC cleared/ Min.: 0 km (0 mile) Max.: 65535 km (40723 mile) | Equivalent to distance driven after DTCs cleared | - |
| Warmup Cycle Cleared DTC | Warm-up cycle after DTC cleared/ Min.: 0, Max.: 255 | - | Number of warm-up cycles after DTCs cleared |
| Number of Emission DTC | Number of emission DTCs | - | - |
| Model Code | Model Code/ | - | - |
| Engine Type | Engine Type/ | - | - |
| Cylinder Number | Cylinder number/ | - | - |
| Destination | Destination/ | - | - |
| Model Year | Model year/ | - | - |
| Engine Speed from EFI | Engine speed/ Min.: 0 rpm Max.: 16383.75 rpm |
| Engine speed received from the ECM. |
| Intake-Air Temp from EFI | Intake air temperature/ Min.: -40°C (-40°F) Max.: 215°C (419°F) | Equivalent to temperature at location of mass air flow meter | Intake air temperature received from the ECM. |
| Coolant Temp from EFI | Engine coolant temperature/ Min.: -40°C (-40°F) Max.: 215°C (419°F) | After warming up engine: 70 to 90°C (158 to 194°F) | Coolant temperature received from the ECM. |
| Accel Position from EFI | Absolute accelerator pedal position/ Min.: 0% Max.: 100% |
| Accel Position received from the ECM. |
| Injection Volume from EFI | Injection volume/ Min.: 0 mm3 Max.: 639.98 mm3 | Idling: 3.0 to 10 mm3/st | Injection Volume received from the ECM. |
| SPD (NC0) | Input turbine speed/ Min.: 0 rpm Max.: 12750 rpm |
| - |
| SPD (SP2) | Output shaft speed/ Min.: 0 km/h (0 mph) Max.: 255 km/h (158 mph) | Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed) | - |
| Shift SW Status (R Range) | PNP switch status/ ON or OFF |
| When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift SW Status (2 Range) | PNP switch status/ ON or OFF |
| When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift SW Status (L Range) | PNP switch status/ ON or OFF |
| When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift SW Status (D Range) | PNP switch status/ ON or OFF |
| When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift SW Status (3 Range) | PNP switch status/ ON or OFF |
| When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| A/T Oil Temperature 3 | ATF temperature sensor value/ Min.: -40°C (-40°F) Max.: 215°C (419°F) |
| If value is -40°C (-40°F) or 215°C (419°F), ATF temperature sensor circuit is opened or short circuited |
| Lock Up | Lock-up/ ON or OFF |
| - |
| Lock Up Solenoid Status | Lock-up solenoid status/ ON or OFF |
| - |
| Shift Status | TCM gear shift command/ 1st, 2nd, 3rd or 4th | Shift lever position is:
| - |
| SLT Solenoid Status | Shift solenoid SLT status/ ON or OFF |
| - |
| PERFORM ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / ECT / Active Test.
According to the display on the tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Connect the TC and TE1 | Turn on and off TC and TE1 connection | ON or OFF | - |
| Activate the Solenoid (SLT)* | Operate shift solenoid valve SLT and raise line pressure | ON or OFF
| [Vehicle Condition]
|
| Activate the Solenoid (S1) | Operate shift solenoid valve S1 | ON or OFF | [Vehicle Condition]
|
| Activate the Solenoid (S2) | Operate shift solenoid valve S2 | ON or OFF | [Vehicle Condition]
|
| Activate the Lock Up | Control shift solenoid valve SL to set automatic transmission to lock-up | ON or OFF | Possible to check shift solenoid valve SL operation. [Vehicle Condition]
|
| Activate the Solenoid (SL) | Operate shift solenoid valve SL | ON or OFF | [Vehicle Condition]
|
| Control the Shift Position | Operate shift solenoid valves and set each shift position |
| Possible to check operation of the shift solenoid valves. [Vehicle Condition] 50 km/h (31 mph) or less |