Home › TRANSMISSION · A340E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM (for 2KD-FTV)

DTC    P0724    Brake Switch "B" Circuit High

for Preparation Click here


DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling while driving in the lock-up condition when the brakes are suddenly applied.
When the brake pedal is depressed, this switch sends a signal to the TCM. Then the TCM cancels the operation of the lock-up clutch while braking is in progress.

DTC Code
DTC Detection Condition
Trouble Area
P0724
Stop light switch remains on even when the vehicle is driven in a stop (less than 3 km/h (2 mph)) and go (30 km/h (19 mph) or more) pattern 5 times (2-trip detection logic).
  1. Short in stop light switch signal circuit
  2. Stop light switch assembly
  3. TCM

MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains on. When the stop light switch remains on during stop and go driving, the TCM interprets this as a fault in the stop light switch. Then the MIL illuminates and the TCM stores the DTC. The vehicle must stop (less than 3 km/h (2 mph)) and go (30 km/h (19 mph) or more) 5 times for 2 driving cycles in order for the DTC to be stored.

WIRING DIAGRAM


C146704E55


INSPECTION PROCEDURE


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / ECT / Data List.

  7. According to the display on the intelligent tester, read the Data List.

    ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light Switch
    Stop light switch status/
    ON or OFF
    1. Brake pedal is depressed: ON
    2. Brake pedal is released: OFF
    -

1.INSPECT STOP LIGHT SWITCH ASSEMBLY


    C228781E01
  1. Remove the stop light switch assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pin not pushed
    Below 1 Ω
    3 - 4
    Pin pushed
    Below 1 Ω
    1 - 2
    Pin pushed
    10 kΩ or higher
    3 - 4
    Pin not pushed
    10 kΩ or higher

    Text in Illustration 
    *1
    Pin
    *a
    Component without harness connected
    (Stop Light Switch Assembly)
    *b
    Not pushed
    *c
    Pushed



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY
OK


2.CHECK HARNESS AND CONNECTOR (BATTERY - TCM)


    C212049E16
  1. Disconnect the T37 TCM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    T37-14 (STP) - Body ground
    Brake pedal depressed
    7.5 to 14 V
    T37-14 (STP) - Body ground
    Brake pedal released
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to TCM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM