VEHICLE STABILITY CONTROL SYSTEM > TEST MODE PROCEDURE |
| TEST MODE PROCEDURE (SIGNAL CHECK) |
Enter Test Mode (when using the intelligent tester).
Turn the ignition switch off.
Check that the steering wheel is in the straight-ahead position.
for Manual Transmission:
Check that the shift lever is in neutral and apply the parking brake.
for Automatic Transmission:
Check that the shift lever is in P.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Switch the skid control ECU to Test Mode using the intelligent tester. Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check.
Check that the ABS warning light and VSC OFF indicator light blink in the Test Mode pattern (0.125 seconds on and 0.125 seconds off).
Enter Test Mode (when using SST check wire).
Turn the ignition switch off.
Check that the steering wheel is in the straight-ahead position.
for Manual Transmission:
Check that the shift lever is in neutral and apply the parking brake.
for Automatic Transmission:
Check that the shift lever is in P.
![]() |
Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.
| *a | Front view of DLC3 |
Turn the ignition switch to ON.
Check that the ABS warning light and VSC OFF indicator light blink in the Test Mode pattern (0.125 seconds on and 0.125 seconds off).
| ABS SIGNAL CHECK |
Acceleration Sensor Check
Enter Test Mode.
Keep the vehicle stationary on a level surface for 1 second or more.
Lost Booster Pressure Judgment Check and Master Cylinder Pressure Sensor Zero Point Calibration
Enter Test Mode.
Release the parking brake.
Check that the brake warning light comes on when depressing the brake pedal with a force of more than 59 N (6 kgf, 13.2 lbf) for 1 second or more (the "lost booster pressure" state is judged as normal).
Start the engine while depressing the brake pedal with a force of more than 59 N (6 kgf, 13.2 lbf) for 1 second or more.
Check that the brake warning light goes off when quickly releasing the brake pedal (the "lost booster pressure" state is judged as normal).
Leave the vehicle for 1 second or more (master cylinder pressure sensor zero point calibration).
Master Cylinder Pressure Sensor Check
Enter Test Mode.
With the vehicle stationary, release the brake pedal for 1 second or more, and then quickly depress and hold the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more for 1 second.
Check that the ABS warning light stays on for 3 seconds.
for 4WD:
Center Differential Lock Position Switch Check
Enter Test Mode.
Move the transfer shift lever from the H position to HL position.
Move the transfer shift lever from the HL position to H position.
Speed Sensor Check
Enter Test Mode.
Start the engine.
Drive the vehicle straight-ahead. Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds.
Check that the ABS warning light goes off.
Stop the vehicle.
| VSC OFF SWITCH CHECK |
Briefly press the VSC OFF switch.
Check that the slip indicator light goes off.
Briefly press the VSC OFF switch again to turn the slip indicator light on.
| END OF SIGNAL CHECK |
If the signal check is completed, the ABS warning light and VSC OFF indicator light blink (0.125 seconds on and 0.125 seconds off) when the vehicle stops and the ABS warning light and VSC OFF indicator light are off while the vehicle is being driven.
| READ DTC OF SIGNAL CHECK FUNCTION |
When using the intelligent tester:
Read the output DTCs by following the tester screen.
Turn the ignition switch off and disconnect the intelligent tester.
When using SST check wire:
![]() |
Using SST, connect terminals 12 (TS), 13 (TC) and 4 (CG) of the DLC3.
| *a | Front view of DLC3 |
Count the number of blinks of the ABS warning light.
Disconnect SST from terminals 12 (TS), 13 (TC) and 4 (CG) of the DLC3 and turn the ignition switch off.
Turn the ignition switch to ON.
| DLC3 | Ignition Switch ON | Ignition Switch Off | Ignition Switch Off → Ignition Switch ON |
| Terminals 12 (TS) and 4 (CG) connected | DTC memory maintained | DTC memory maintained | DTC memory maintained |
| Terminals 12 (TS) and 4 (CG) not connected | DTC memory maintained | DTC memory maintained | DTC memory cleared |
| LIST OF TEST MODE (SIGNAL CHECK) DTC |
| DTC Code | Detection Item | Trouble Area | |
| Intelligent Tester Display | ABS Warning Light Display | ||
| C1271 | 71 | Low output signal of front speed sensor RH |
|
| C1272 | 72 | Low output signal of front speed sensor LH |
|
| C1273 | 73 | Low output signal of rear speed sensor RH |
|
| C1274 | 74 | Low output signal of rear speed sensor LH |
|
| C1275 | 75 | Abnormal change in output signal of front speed sensor RH |
|
| C1276 | 76 | Abnormal change in output signal of front speed sensor LH |
|
| C1277 | 77 | Abnormal change in output signal of rear speed sensor RH |
|
| C1278 | 78 | Abnormal change in output signal of rear speed sensor LH |
|
| C1279 | 79 | Acceleration sensor output voltage malfunction |
|
| C1281 | 81 | Master cylinder pressure sensor output malfunction | Brake actuator assembly (Master cylinder pressure) |
| C1282* | 82* | Center differential lock position switch malfunction |
|