VEHICLE STABILITY CONTROL SYSTEM > DTC CHECK / CLEAR |
| DTC CHECK/CLEAR (When Using Intelligent Tester) |
Check for DTCs.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / DTC.
Check the details of the DTCs.
Clear the DTCs.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / DTC.
Clear the DTCs by following the prompts on the intelligent tester.
| DTC CHECK/CLEAR (When Using SST Check Wire) |
![]() |
Check for DTCs.
| *a | Front view of DLC3 |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
Turn the ignition switch to ON.
Read the DTCs output from the ABS warning light and slip indicator light in the combination meter.
Warning and indicator light codes are defined in the following charts.
| ABS Warning Light Display | DTC Code |
| 11 | C0278 |
| 12 | C0279 |
| 13 | C0273 |
| 14 | C0274 |
| 21 | C0226 |
| 22 | C0236 |
| 23 | C0246 |
| 24 | C0256 |
| 25 | C1225 |
| 31 | C1401 |
| C1405 | |
| 32 | C1402 |
| C1406 | |
| 33 | C1403 |
| C1407 | |
| 34 | C1404 |
| C1408 | |
| 35 | C1413 |
| 36 | C1414 |
| 37 | C1337 |
| 38 | C1415 |
| 39 | C1416 |
| 41 | C1241 |
| C1417 | |
| 43 | C1243 |
| 44 | C1419 |
| C1420 | |
| C1442 | |
| 45 | C1245 |
| 46 | C1421 |
| C1422 | |
| C1423 | |
| C1424 | |
| 49 | C1425 |
| C1426 | |
| 51 | C1427 |
| C1428 | |
| 67 | C1429 |
| C1430 | |
| C1431 | |
| 68 | C1268 |
| 91 | C1361 |
| 94 | U0073 |
| 95 | U0124 |
| 97 | C1381 |
| Slip Indicator Light Display | DTC Code |
| 31 | C1432 |
| C1433 | |
| C1434 | |
| 32 | C1232 |
| 34 | C1435 |
| C1436 | |
| C1443 | |
| 36 | C1210 |
| 39 | C1336 |
| 43* | - |
| 51 | C1201 |
| 53 | C1203 |
| 62 | U0123 |
| 63 | U0126 |
| 65 | C1437 |
| U0100 | |
| 66 | C1290 |
| C1439 | |
| C1445 | |
| 98 | C1440 |
| C1441 |
Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.
Clear the DTCs.
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
| *a | Front view of DLC3 |
Turn the ignition switch to ON.
Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.
Check that the ABS warning light and slip indicator light blink at 0.25 second intervals (0.25 seconds on and 0.25 seconds off).
Remove SST from the terminals of the DLC3.
| END OF DTC CHECK/CLEAR |
Turn the ignition switch to ON.
Check that the ABS warning light and slip indicator light go off within approximately 3 seconds after turning the ignition switch to ON.