DTC 19 (1) Accelerator Position Sensor Circuit Malfunction |

| DTC No. | DTC Detection Condition | Trouble Area |
| 19 (1) | Condition (a), (b), (c) or (d) continues for 2.0 seconds: (a) VPA is less than or equal to 0.2 V, and VPA2 is less than or equal to 0.5 V (b) VPA is greater than or equal to 4.8 V (c) When 3.45 V is greater than or equal to VPA, and VPA is greater than or equal to 0.2 V; and VPA2 is greater than or equal to 4.8 V (d) "VPA minus VPA2" is less than or equal to 0.02 V |
|
| Condition (a) continues for 0.5 seconds: (a) VPA is less than or equal to 0.2 V, or VPA2 is less than or equal to 0.5 V |
| Trouble area | Accelerator pedal position expressed as voltage | |||
| Accelerator pedal released | Accelerator pedal depressed | |||
| ACCEL POS #1 | ACCEL POS #2 | ACCEL POS #1 | ACCEL POS #2 | |
| VC circuit open | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V |
| VPA circuit open or ground short | 0 to 0.2 V | 1.2 to 2.0 V | 0 to 0.2 V | 3.4 to 5.3 V |
| VPA2 circuit open or ground short | 0.5 to 1.1 V | 0 to 0.2 V | 2.6 to 4.5 V | 0 to 0.2 V |
| E2 circuit open | 4.5 to 5.5 V | 4.5 to 5.5 V | 4.5 to 5.5 V | 4.5 to 5.5 V |

| 1.READ VALUE USING INTELLIGENT TESTER (ACCELERATOR POSITION) |
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Position.
Check that the value displayed on the intelligent tester changes when repeatedly depressing and releasing the accelerator pedal.
|
| ||||
| OK | |
| 2.READ OUTPUT DTC (ACCELERATOR PEDAL POSITION SENSOR DTC IS OUTPUT AGAIN) |
Clear the DTC (Click here).
Start the engine.
Idle the engine for 15 seconds or more.
Read the DTC (Click here).
| Display (DTC output) | Proceed to |
| DTC 19 (1) is output again | A |
| No DTC output | B |
|
| ||||
| A | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (ECM - ACCELERATOR PEDAL POSITION SENSOR) |
![]() |
Disconnect the A22 accelerator pedal position sensor connector.
Disconnect the E21 and E25 ECM connectors.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| A22-1 (VCP2) - E21-1 (VC) | Below 1 Ω |
| A22-2 (EPA2) - E21-9 (E2) | Below 1 Ω |
| A22-3 (VPA2) - E25-12 (VPA2) | Below 1 Ω |
| A22-4 (VCPA) - E25-6 (VCPA) | Below 1 Ω |
| A22-5 (EPA) - E25-4 (EPA) | Below 1 Ω |
| A22-6 (VPA) - E25-5 (VPA) | Below 1 Ω |
| A22-1 (VCP2) or E21-1 (VC) - Body ground | 10 kΩ or higher |
| A22-2 (EPA2) or E21-9 (E2) - Body ground | 10 kΩ or higher |
| A22-3 (VPA2) or E25-12 (VPA2) - Body ground | 10 kΩ or higher |
| A22-4 (VCPA) or E25-6 (VCPA) - Body ground | 10 kΩ or higher |
| A22-5 (EPA) or E25-4 (EPA) - Body ground | 10 kΩ or higher |
| A22-6 (VPA) or E25-5 (VPA) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK ECM (VC, VCPA VOLTAGE) |
![]() |
Disconnect the A22 accelerator pedal position sensor connector.
Turn the ignition switch ON.
Measure the voltage of the ECM connector.
| Tester Connection | Specified Condition |
| E21-1 (VC) - E21-9 (E2) | 4.5 to 5.5 V |
| E25-6 (VCPA) - E25-4 (EPA) | 4.5 to 5.5 V |
|
| ||||
| OK | |
| 5.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY |
| NEXT | |
| 6.READ OUTPUT DTC (ACCELERATOR PEDAL POSITION SENSOR DTC IS OUTPUT AGAIN) |
Clear the DTC (Click here).
Start the engine.
Idle the engine for 15 seconds or more.
Read the DTC (Click here).
| Display (DTC output) | Proceed to |
| DTC 19 (1) is output again | A |
| No DTC output | B |
|
| ||||
| A | ||
| ||
| 1.CHECK HARNESS AND CONNECTOR (ECM - ACCELERATOR PEDAL POSITION SENSOR) |
![]() |
Disconnect the A22 accelerator pedal position sensor connector.
Disconnect the E21 and E25 ECM connectors.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| A22-1 (VCP2) - E21-1 (VC) | Below 1 Ω |
| A22-2 (EPA2) - E21-9 (E2) | Below 1 Ω |
| A22-3 (VPA2) - E25-12 (VPA2) | Below 1 Ω |
| A22-4 (VCPA) - E25-6 (VCPA) | Below 1 Ω |
| A22-5 (EPA) - E25-4 (EPA) | Below 1 Ω |
| A22-6 (VPA) - E25-5 (VPA) | Below 1 Ω |
| A22-1 (VCP2) or E21-1 (VC) - Body ground | 10 kΩ or higher |
| A22-2 (EPA2) or E21-9 (E2) - Body ground | 10 kΩ or higher |
| A22-3 (VPA2) or E25-12 (VPA2) - Body ground | 10 kΩ or higher |
| A22-4 (VCPA) or E25-6 (VCPA) - Body ground | 10 kΩ or higher |
| A22-5 (EPA) or E25-4 (EPA) - Body ground | 10 kΩ or higher |
| A22-6 (VPA) or E25-5 (VPA) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 2.CHECK ECM (VC, VCPA VOLTAGE) |
![]() |
Disconnect the A22 accelerator pedal position sensor connector.
Turn the ignition switch ON.
Measure the voltage of the ECM connector.
| Tester Connection | Specified Condition |
| E21-1 (VC) - E21-9 (E2) | 4.5 to 5.5 V |
| E25-6 (VCPA) - E25-4 (EPA) | 4.5 to 5.5 V |
|
| ||||
| OK | |
| 3.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY |
| NEXT | |
| 4.READ OUTPUT DTC (ACCELERATOR PEDAL POSITION SENSOR DTC IS OUTPUT AGAIN) |
Clear the DTC (Click here).
Start the engine.
Idle the engine for 15 seconds or more.
Read the DTC (Click here).
| Display (DTC output) | Proceed to |
| DTC 19 (1) is output again | A |
| No DTC output | B |
|
| ||||
| A | ||
| ||