FUEL TANK > REMOVAL |
| 1. DISCHARGE FUEL SYSTEM PRESSURE |
Disconnect the cable from the negative (-) battery terminal.
Remove the front driver side scuff plate.
Using a screwdriver, detach the 7 claws.
Using a clip remover, detach the 3 clips and remove the scuff plate.
![]() |
Fold back the floor carpet and disconnect the joining connector, as shown in the illustration.
Connect the cable to the negative (-) battery terminal.
Start the engine. After the engine has stopped on its own, turn the ignition switch OFF.
Crank the engine again, and then check that the engine does not start.
Loosen the fuel tank cap, and then discharge the pressure in the fuel tank completely.
Connect the fuel pump connector.
Install the front driver side scuff plate.
Clear the DTCs (Click here).
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE FUEL TANK CAP ASSEMBLY |
| 4. REMOVE FUEL TANK PROTECTOR |
![]() |
Remove the 4 nuts and fuel tank protector.
| 5. REMOVE NO. 3 FUEL TUBE CLAMP |
![]() |
Remove the 2 tube clamps from the fuel tube.
| 6. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY AND FUEL TANK RETURN TUBE |
![]() |
Pinch and pull the fuel tank main tube connector to disconnect the connector from the pipe. Then pinch and pull the fuel tank return tube connector to disconnect the connector from the pipe.
Disconnect the vent line hose from the fuel pipe.
| 7. DISCONNECT FUEL TANK BREATHER HOSE |
![]() |
Disconnect the fuel tank breather hose from the fuel tank filler pipe.
Detach the fuel tank breather hose from the 2 clamps.
| 8. DISCONNECT FUEL TANK TO FILLER PIPE HOSE |
Disconnect the fuel tank to filler pipe hose from the fuel tank filler pipe.
| 9. REMOVE FUEL TANK FILLER PIPE |
Remove the bolt, nut and filler pipe.
| 10. REMOVE FUEL TANK ASSEMBLY |
Place a transmission jack under the fuel tank.
![]() |
Remove the 3 bolts, 3 clips, 3 pins and 3 fuel tank bands.
Slightly lower the transmission jack.
![]() |
Fold back approximately half of each cushion so that the wire harness can be removed in the step below.
![]() |
Detach the wire harness from the 4 clamps shown in the illustration.
Disconnect the fuel pump and sender gauge connector.
| 11. REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY |
![]() |
Using needle-nose pliers, remove the 5 clips and 2 nuts shown in the illustration and then remove the No. 1 fuel tank protector.
| 12. REMOVE FUEL TANK CUSHION |
![]() |
Remove the 4 fuel tank cushions from the fuel tank.
| 13. REMOVE NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY |
![]() |
Remove the No. 1 fuel evaporation tube.
| 14. REMOVE FUEL PUMP GAUGE RETAINER |
![]() |
Remove the 2 tube joint clips and pull out the 2 fuel tank tubes.

Remove the fuel tank return tube and fuel tank main tube from the fuel tank.
![]() |
Set SST on the fuel pump gauge retainer.
![]() |
Using SST, loosen the retainer.
Remove the fuel pump gauge retainer.
| 15. REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY |
Remove the fuel suction with pump and gauge tube from the fuel tank.
Remove the gasket from the fuel tank.
| 16. REMOVE FUEL TANK BREATHER HOSE |
![]() |
Remove the fuel tank breather hose from the fuel tank.
| 17. REMOVE FUEL TANK TO FILLER PIPE HOSE |
Remove the fuel tank to filler pipe hose from the fuel tank.