Home › ENGINE ยท 1GR-FE › LUBRICATION › OIL PUMP

OIL PUMP > REMOVAL

for Preparation Click here



1. REMOVE ENGINE ASSEMBLY
  1. Remove the engine from the vehicle (Click here).



2. INSTALL ENGINE TO ENGINE STAND
  1. Install the engine assembly to a stand.



3. REMOVE OIL DIPSTICK GUIDE
  1. Remove the oil dipstick gauge.

  1. Remove the bolt and oil dipstick guide.

  1. Remove the O-ring from the oil dipstick guide.



4. REMOVE WATER INLET


    A112082
  1. Remove the 3 nuts, water inlet housing with thermostat and gasket.



5. REMOVE V-RIBBED BELT TENSIONER


    A076445E01
  1. Remove the 5 bolts and V-ribbed belt tensioner.



6. REMOVE NO. 2 IDLER PULLEY

NOTICE:
Use the same procedure for both No. 2 idler pulleys.



  1. w/ Idler Pulley Cover Plate:



      A191314E01
    1. Remove the bolt, No. 2 idler pulley cover plate, idler pulley and idler pulley cover plate.



  1. w/o Idler Pulley Cover Plate:



      A191315E01
    1. Remove the bolt, No. 2 idler pulley cover plate and idler pulley.



    A076338E01
  1. for Integrated Type:
    Remove the 2 bolts and 2 No. 2 idler pulleys.



7. REMOVE NO. 1 IDLER PULLEY
  1. Remove the bolt and idler pulley.



8. REMOVE CRANKSHAFT PULLEY


    A072945E01
  1. Turn the crankshaft pulley, and align its groove with timing mark 0 of the timing chain cover.



    G038065E08
  1. Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
    If not, turn the crankshaft 1 revolution (360°) and align the timing marks as described above.



    A072947E01
  1. Using SST, hold the crankshaft pulley and loosen the pulley set bolt.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A072948E01
  1. Using the pulley set bolt and SST, remove the crankshaft pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05030)



9. REMOVE NO. 2 OIL PAN


    A112956E01
  1. Remove the 14 bolts and 2 nuts.



    A112957
  1. Insert the blade of an oil pan seal cutter between the oil pan and No. 2 oil pan, cut through the applied sealer and remove the No. 2 oil pan.

    NOTICE:
    1. Be careful not to damage the contact surfaces of the No. 1 oil pan and No. 2 oil pan.
    2. Be careful not to damage the No. 2 oil pan flange.



10. REMOVE OIL STRAINER


    A112955
  1. Remove the bolt, 2 nuts, oil strainer and gasket.



11. REMOVE NO. 1 OIL PAN


    A112952E02
  1. Remove the 17 bolts and 2 nuts.



    A112954
  1. Using a screwdriver, remove the oil pan by prying between the oil pan and cylinder block as shown in the illustration.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.

  1. Remove the O-ring from the oil pump.



12. REMOVE IGNITION COIL


13. REMOVE CYLINDER HEAD COVER RH


    A072943E01
  1. Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.



14. REMOVE CYLINDER HEAD COVER LH


    A076503E01
  1. Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.



15. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE (for Bank 1)


A111699
  1. Disconnect the oil control valve connector.

  1. Remove the bolt and oil control valve.

  1. Remove the O-ring from the oil control valve.



16. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE (for Bank 2)


A111700
  1. Disconnect the oil control valve connector.

  1. Remove the bolt and oil control valve.

  1. Remove the O-ring from the oil control valve.



17. REMOVE VVT SENSOR


    G038105
  1. Disconnect the sensor connector.

  1. Remove the bolt and sensor.



18. REMOVE OIL FILTER SUB-ASSEMBLY


    A076806E01
  1. Remove the drain pipe cap.

  1. While removing the oil filter with SST, collect the oil from the oil filter in a container.

    SST
    09228-07501  

  1. Install the drain pipe cap.

  1. Clean the container.



19. REMOVE OIL FILTER BRACKET
  1. Remove the 3 bolts, 2 nuts, oil filter bracket and gasket.



20. REMOVE TIMING CHAIN COVER


    G038101E02
  1. Remove the 24 bolts and 2 nuts.



    G038102E01
  1. Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing chain cover, cylinder block and cylinder head.

  1. Remove the O-ring from the LH cylinder head.



21. REMOVE TIMING CHAIN COVER OIL SEAL
  1. Using a screwdriver, pry out the oil seal.

    NOTICE:
    Be careful not to damage the oil pump body.

    HINT:
    Tape the screwdriver tip before use.



    A076300E01
  1. Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing chain cover edge.

    SST
    09226-10010  

  1. Apply MP grease to the lip of the oil seal.