ENGINE ASSEMBLY > REMOVAL |
| 1. DISCHARGE FUEL SYSTEM PRESSURE |
Disconnect the cable from the negative (-) battery terminal.
![]() |
Disconnect the fuel pump connector.
Connect the cable to the negative (-) battery terminal.
Start the engine. After the engine has stopped on its own, turn the ignition switch OFF.
Crank the engine again, and check that the engine does not start.
Loosen the fuel tank cap, and then discharge the pressure in the fuel tank completely.
Connect the fuel pump connector.
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. DRAIN ENGINE COOLANT |
Remove the radiator cap.

Loosen the cylinder block drain cock plug and radiator drain cock plug, and then drain the coolant.
| 4. DRAIN ENGINE OIL |
Remove the oil filler cap.
Remove the engine under cover.
Remove the oil pan drain plug and drain the engine oil into a container.
| 5. REMOVE BATTERY |
| 6. REMOVE HOOD |
Disconnect the washer nozzle hose.
Remove the 4 bolts and hood.
| 7. REMOVE V-BANK COVER |
![]() |
Remove the 2 nuts and V-bank cover.
| 8. DISCONNECT NO. 2 VENTILATION HOSE |
![]() |
| 9. REMOVE AIR CLEANER |
![]() |
Disconnect the vacuum hose.
Disconnect the MAF meter connector.
Remove the 2 wire harness clamps.
![]() |
Loosen the 2 hose clamps.
Remove the 2 bolts and air cleaner.
| 10. REMOVE RADIATOR GRILLE |
![]() |
Remove the 2 clips and 2 screws.
![]() |
Put protective tape around the radiator grille.
| *1 | Protective Tape |
Detach the 6 claws and remove the radiator grille.
| 11. REMOVE RADIATOR SIDE DEFLECTOR LH |
![]() |
Using a clip remover, remove the 2 clips.
Detach the claw and remove the deflector.
| 12. REMOVE RADIATOR SIDE DEFLECTOR RH |
Using a clip remover, remove the 2 clips.
Detach the claw and remove the deflector.
| 13. REMOVE FAN SHROUD |
![]() |
Remove the 3 bolts and oil reservoir.
Disconnect the reservoir hose from the radiator tank upper.
Loosen the 4 nuts holding the fluid coupling fan.
Remove the drive belt .
Remove the 2 bolts holding the fan shroud.
Remove the 4 nuts holding the fluid coupling fan, and then remove the shroud together with the fluid coupling fan.
Remove the fan pulley from the water pump.
| 14. LOOSEN FAN WITH FLUID COUPLING |
| 15. REMOVE DRIVE BELT |
![]() |
While releasing the belt tension by turning the belt tensioner counterclockwise, remove the V-ribbed belt from the belt tensioner.
| 16. REMOVE FAN WITH FLUID COUPLING |
Remove the 4 nuts and fan with fluid coupling.
| 17. REMOVE FAN PULLEY |
| 18. REMOVE RADIATOR |
![]() |
Disconnect the 2 front airbag sensor connectors.
Using a clip remover, detach the 4 clamps shown in the illustration from the radiator side.
![]() |
Remove the 4 bolts and radiator.
| 19. DISCONNECT VANE PUMP |
![]() |
Disconnect the oil pressure switch connector.
Remove the 2 bolts, and disconnect the vane pump.
| 20. REMOVE GENERATOR ASSEMBLY |
![]() |
Disconnect the terminal cap.
Remove the 2 bolts, nut and generator wire.
Disconnect the generator connector.
Remove the 2 bolts and generator.
| 21. DISCONNECT COOLER COMPRESSOR ASSEMBLY |
![]() |
Remove the 2 bolts and disconnect the suction hose from the engine.
![]() |
Disconnect the cooler compressor connector.
Remove the 4 bolts and disconnect the compressor from the engine.
Support the cooler compressor securely.
| 22. DISCONNECT NO. 1 FUEL PIPE |
![]() |
Remove the fuel pipe clamp.
Pinch the tube connector and then pull out the fuel pipe.

| 23. DISCONNECT NO. 2 FUEL PIPE |
![]() |
Remove the fuel pipe clamp.
Pinch the tube connector and then pull out the fuel pipe.

| 24. DISCONNECT HEATER HOSE |
![]() |
Disconnect the heater water inlet hose.
Disconnect the heater water outlet hose.
| 25. REMOVE INTAKE AIR SURGE TANK |
![]() |
Disconnect the 2 water by-pass hoses.
![]() |
Disconnect the purge line hose.
![]() |
Disconnect the ventilation hose.
![]() |
Disconnect the 2 VSV connectors.
Disconnect the throttle body with motor connector.
Separate the 3 wire harness clamps and hose clamp.
![]() |
Remove the 2 bolts and throttle body bracket.
![]() |
Remove the bolt and oil baffle plate.
Remove the 4 bolts and 2 surge tank stays.
![]() |
Remove the 2 nuts.
Using an 8 mm hexagon socket wrench, remove the 4 bolts, intake air surge tank and gasket.
| 26. DISCONNECT ENGINE WIRE |
![]() |
Disconnect the ECM connectors from the cabin:
Remove the glove compartment door.
Disconnect the 5 ECM connectors.
Disconnect the 4WD control ECU connector.
Remove the nut, and disconnect the ground wire.
Remove the bolt and disconnect the ground wire from the frame.
Pull the end of the engine wire into the engine compartment.
![]() |
Remove the upper relay block cover.
Remove the side relay block cover.
Using a screwdriver, detach the 4 claws and remove the relay block cover.
Remove the nut and disconnect the cable from the engine room junction block.
Disconnect the 2 engine room junction block connectors and detach the wire clamp.
Remove the bolt and disconnect the wire clamp from the engine mounting bracket front LH.
Disconnect the 2 A/F sensor connectors.
Disconnect the A.D.D. connector.
| 27. DISCONNECT NO. 2 ENGINE WIRE |
Disconnect the No. 2 engine wire from the cylinder block.
| 28. REMOVE FRONT EXHAUST PIPE |
Remove the 2 nuts, gasket, pipe support and exhaust pipe.
| 29. REMOVE FRONT FENDER SEAL |
Remove the front tires.
Remove the 10 clips and RH and LH fender seals.
| 30. REMOVE FRONT FENDER APRON SEAL UPPER |
Remove the 10 clips and RH and LH fender apron seals.
| 31. REMOVE EXHAUST MANIFOLD RH |
Remove the 6 nuts, exhaust manifold and gasket.
| 32. REMOVE EXHAUST MANIFOLD LH |
Remove the 6 nuts, exhaust manifold and gasket.
| 33. REMOVE STARTER |
![]() |
Disconnect the starter connector.
Remove the nut and disconnect the starter wire.
![]() |
Remove the 2 bolts and starter.
| 34. REMOVE AUTOMATIC TRANSMISSION |
for A750F:
Remove the automatic transmission from the vehicle (Click here).
for A750E:
Remove the automatic transmission from the vehicle (Click here).
| 35. REMOVE DRIVE PLATE AND RING GEAR ASSEMBLY |
![]() |
Using SST, hold the crankshaft.
![]() |
Remove the 8 bolts, rear spacer, drive plate and front spacer.
| 36. REMOVE ENGINE ASSEMBLY |
![]() |
Install the 2 engine hangers with 4 bolts as shown in the illustration.
| Item | Part No |
| No. 1 engine hanger | 12281-31060 |
| No. 2 engine hanger | 12282-31040 |
| Bolt | 90119-08A87 |
Attach the engine sling device and chain block to the engine hangers.
![]() |
Remove the 4 bolts and 4 nuts holding the engine mounting brackets to the frame.
![]() |
Lift the engine out of the vehicle carefully.
| 37. INSTALL ENGINE TO ENGINE STAND |
Install the engine assembly to a stand.
| 38. REMOVE ENGINE WIRE FROM ENGINE ASSEMBLY |
| 39. REMOVE NO. 1 RADIATOR HOSE |
| 40. REMOVE NO. 2 RADIATOR HOSE |
| 41. REMOVE HEATER HOSE FROM ENGINE ASSEMBLY |
| 42. REMOVE VENTILATION HOSE |
| 43. REMOVE NO. 2 VENTILATION HOSE |
| 44. REMOVE FRONT ENGINE MOUNTING INSULATOR RH |
Remove the 4 bolts and engine mounting bracket with engine mounting insulator.
| 45. REMOVE FRONT ENGINE MOUNTING INSULATOR LH |
Remove the 3 bolts and engine mounting bracket with engine mounting insulator.
| 46. REMOVE IDLER PULLEY |
Remove the 3 bolts and idler pulley.
| 47. REMOVE V-RIBBED BELT TENSIONER |
![]() |
Remove the 5 bolts and V-ribbed belt tensioner.
| 48. REMOVE WATER INLET HOUSING |
![]() |
Remove the 3 nuts, water inlet housing with thermostat and gasket.
| 49. REMOVE OIL FILTER BRACKET |
Remove the 3 bolts, 2 nuts, oil filter bracket and gasket.
| 50. REMOVE INTAKE MANIFOLD |
![]() |
Disconnect the 6 fuel injector connectors.
Remove the 10 bolts, intake manifold and 2 gaskets.
| 51. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE |
Remove the 2 bolts and 2 camshaft timing oil control valves.
| 52. REMOVE REAR WATER BY-PASS JOINT |
Disconnect the engine coolant temperature sensor connector.
![]() |
Remove the 2 bolts, 4 nuts, water by-pass joint and 2 gaskets.
Remove the O-ring from the water outlet pipe.
| 53. REMOVE OIL FILLER CAP |
| 54. REMOVE OIL FILLER CAP HOUSING |
Remove the 2 nuts, oil filler cap housing and gasket.
| 55. REMOVE IGNITION COIL |
Remove the 6 bolts and 6 ignition coils.
| 56. REMOVE SPARK PLUG |
| 57. REMOVE OIL DIPSTICK GUIDE |
Remove the oil dipstick gauge.
Remove the bolt and pull out the oil dipstick gauge guide.
Remove the O-ring from the oil dipstick gauge guide.
| 58. REMOVE NO. 2 IDLER PULLEY |
w/ Idler Pulley Cover Plate:
![]() |
Remove the bolt, No. 2 idler pulley cover plate, idler pulley and idler pulley cover plate.
w/o Idler Pulley Cover Plate:
![]() |
Remove the bolt, No. 2 idler pulley cover plate and idler pulley.
![]() |
for Integrated Type:
Remove the 2 bolts and 2 No. 2 idler pulleys.
| 59. REMOVE NO. 1 IDLER PULLEY |
Remove the bolt and idler pulley.