ENGINE ASSEMBLY > INSTALLATION |
| 1. INSTALL FRONT ENGINE MOUNTING BRACKET LH |
![]() |
Install the mounting bracket with the 4 bolts.
| 2. INSTALL FRONT ENGINE MOUNTING BRACKET RH |
![]() |
Install the mounting bracket with the 4 bolts.
| 3. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE |
![]() |
Apply a coat of engine oil to a new O-ring.
Install a new O-ring to the oil control valve.
Install the oil control valve with the bolt.
| 4. INSTALL CRANKSHAFT POSITION SENSOR |
![]() |
Apply a light coat of engine oil to the O-ring of the sensor.
Install the sensor with the bolt.
Install the connector to the connector bracket.
Attach the harness clamp.
Connect the sensor connector.
| 5. INSTALL CAMSHAFT POSITION SENSOR |
![]() |
Apply a coat of engine oil to a new O-ring.
Install the O-ring to the sensor.
Install the sensor with the bolt.
| 6. INSTALL ENGINE COOLANT TEMPERATURE SENSOR |
Using a 19 mm deep socket wrench, install a new gasket and the sensor.
| 7. INSTALL KNOCK SENSOR |
![]() |
Install the sensor so that it is horizontal as shown in the illustration. Then install the bolt.
Connect the sensor connector.
| 8. INSTALL NO. 1 WATER BY-PASS PIPE |
![]() |
Install a new gasket and the water by-pass pipe with the 2 nuts.
| 9. INSTALL ENGINE OIL PRESSURE SWITCH |
![]() |
Apply adhesive to 2 or 3 threads of the oil pressure switch.
Install the oil pressure switch.
Connect the oil pressure switch connector.
Start the engine and check for engine oil leaks.
| 10. INSTALL NO. 1 IDLER PULLEY |
![]() |
Install the spacer, idler pulley and pulley plate with the bolt.
| 11. INSTALL THERMOSTAT |
![]() |
Install a new gasket to the thermostat.
Insert the thermostat into the cylinder block with the jiggle valve facing straight upward.
| 12. INSTALL WATER INLET |
![]() |
Install the inlet with the 2 nuts and bolt.
![]() |
Connect the connector.
| 13. INSTALL V-RIBBED BELT TENSIONER |
![]() |
Temporarily install the belt tensioner with the 3 bolts.
Install the tensioner by tightening the 3 bolts in the order shown in the illustration.
| 14. INSTALL COMPRESSOR MOUNTING BRACKET |
![]() |
Temporarily install the compressor mounting bracket with the 3 bolts.
Push the compressor mounting bracket toward the cylinder block as shown in the illustration and tighten bolt B.

![]() |
Uniformly tighten the 4 bolts in the order shown in the illustration.
| 15. INSTALL IDLE PULLEY ASSEMBLY |
Temporarily install the idle pulley assembly with the bolt.
Tighten the bolt.
| 16. INSTALL EXHAUST MANIFOLD |
![]() |
Install a new gasket and the exhaust manifold with the 6 nuts.
| 17. INSTALL EXHAUST MANIFOLD HEAT INSULATOR |
![]() |
Install the heat insulator with the 5 bolts.
| 18. INSTALL INTAKE MANIFOLD |
![]() |
Install a new gasket and the intake manifold with the 5 bolts and 2 nuts.
Connect the crankshaft position sensor to the clamp.
| 19. INSTALL INJECTOR |
Install each of the 4 injectors as follows.
![]() |
Install a new insulator to the injector.
Apply a light coat of grease or gasoline to a new O-ring and install it to the injector.
Apply a light coat of grease or gasoline on the place where the delivery pipe touches the O-ring.
![]() |
To install the fuel injector into the fuel delivery pipe, push the fuel injector while twisting it right and left.
Position the injector connector so that it faces downward.
| 20. INSTALL FUEL DELIVERY PIPE |
![]() |
Install the 4 spacers to the cylinder head.
![]() |
Install the delivery pipe together with the 4 injectors and 2 spacers with the 2 bolts.
Connect the 4 injector connectors.
![]() |
Connect the 4 clamps and wire harness to the delivery pipe.
Connect the vacuum hose.
| 21. INSTALL THROTTLE BODY |
![]() |
Install a new gasket on the intake manifold.
![]() |
Install the throttle body with the 4 bolts.
Connect the 2 water by-pass hoses to the throttle body.
Connector the throttle position sensor and control motor connector.
| 22. INSTALL ENGINE WIRE |
![]() |
Connect the wire harness (engine ground wire) to the engine rear side with the 2 bolts so that it is within the specified range shown in the illustration.
Connect the oil pressure sensor connector.
Connect the noise filter connector.
Connect the camshaft position sensor connector.
Connect the 4 injector connectors.
Connect the crankshaft position sensor connector.
Connect the oil control valve connector.
Connect the purge VSV connector.
Connect the throttle body connector.
Connect the engine coolant temperature sensor connector.
Connect the knock sensor connector.
Connect the wire harness to the clamps.
| 23. INSTALL GENERATOR |
![]() |
Install the generator with the 2 bolts.
Install the generator wire with the bolt and nut.
Attach the terminal cap.
Connect the connector.
| 24. INSTALL VENTILATION PIPE |
Install the ventilation pipe with the bolt.
| 25. INSTALL SPARK PLUG |
| 26. INSTALL IGNITION COIL |
Install the 4 ignition coils with the 4 bolts.
Connect the 4 ignition coil connectors.
| 27. REMOVE ENGINE FROM ENGINE STAND |
| 28. INSTALL ENGINE ASSEMBLY |
![]() |
Attach the engine sling device and chain block to the engine hangers.
Slowly lower the engine assembly into the engine compartment.
![]() |
Install the engine mounting brackets with the 4 bolts and 4 nuts.
| 29. INSTALL REAR END PLATE |
Install the end plate with the 2 bolts.
| 30. INSTALL DRIVE PLATE |
![]() |
Apply adhesive to 2 or 3 threads of the mounting bolt end.
Install the drive plate.
![]() |
Fix the crankshaft in place with SST.
![]() |
Install and uniformly tighten the 10 mounting bolts in several passes in the order shown in the illustration.
| 31. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY |
| 32. INSTALL STARTER |
![]() |
Install the starter with the 2 bolts.
Install the starter wire to terminal 30 with the nut.
Attach the terminal cap.
Connect the starter connector.
| 33. INSTALL REAR PROPELLER SHAFT ASSEMBLY |
![]() |
Align the matchmarks on the propeller shaft flange and transfer flange.
Connect the propeller shaft with the 4 washers and 4 nuts.
Align the matchmarks on the propeller shaft flange and differential flange.
![]() |
Install the propeller shaft with the 4 bolts, 4 washers and 4 nuts.
| 34. INSTALL FRONT PROPELLER SHAFT ASSEMBLY |
![]() |
Align the matchmarks on the yoke and transfer flange.
Connect the propeller shaft with the 4 washers and 4 nuts.
![]() |
Align the matchmarks on the yoke and differential flange.
Install the front propeller shaft with the 4 bolts, 4 washers and 4 nuts.
| 35. INSTALL FRONT EXHAUST PIPE |
![]() |
Using a vernier caliper, measure the free length of the compression spring.
Install the front pipe to the pipe support.
![]() |
Install a new gasket to the exhaust manifold.
Install the front pipe with the 2 compression springs and 2 bolts. Alternately tighten the bolts in several passes.
| 36. INSTALL HOOD ASSEMBLY |
Install the hood with the 4 bolts.
Connect the washer nozzle hose.
Adjust the hood (Click here).
| 37. INSTALL COOLER COMPRESSOR |
![]() |
Loosely install the bolt labeled A to install the compressor.
Install the compressor completely by tightening the 4 bolts in the order shown in the illustration.
![]() |
Connect the suction hose with the 2 bolts.
Connect the compressor connector.
| 38. INSTALL OIL DIPSTICK GUIDE |
Install a new O-ring and the dipstick guide with the bolt.
| 39. INSTALL OIL DIPSTICK |
| 40. INSTALL VANE PUMP |
![]() |
Install the vane pump with the 2 bolts.
Connect the PS oil pressure switch connector.
| 41. CONNECT ENGINE WIRE |
![]() |
Connect the 2 engine room junction block connectors and connect the wire clamp.
Connect the cable to the engine room junction block with the nut.
Install the engine room relay block cover (upper).
Install the engine room relay block cover (side).
Connect the ground wire with the bolt and clamp.
![]() |
Connect the ground wire to the frame with the bolt so that it is within the range shown in the illustration.
Push the engine wire through the dash panel into the cabin. The wire should be within the range shown in the illustration.
Connect the sensor clamp with the bolt.
![]() |
Connect the ECM connectors.
Connect the 4 ECM connectors.
Install the glove compartment door.
Connect the wire clamp to the engine mounting bracket front LH with the bolt.
| 42. CONNECT FUEL HOSE |
![]() |
Connect the No. 2 fuel hose to the pressure regulator.
Connect the No. 1 fuel hose to the pulsation damper.
![]() |
Check that there is no damage or contamination in the connected part of the pipe.
Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a "click" sound. If the connection is tight, apply a small amount of fresh engine oil on the tip of the pipe.
![]() |
After having finished the connection, try to pull apart the pipe and the connector and confirm that they are securely connected.
![]() |
Attach the lock claws to the connector by pushing down on the cover, as shown in the illustration.
| 43. CONNECT HOSE |
![]() |
Connect the vacuum hose to the intake manifold.
Connect the hose to the purge VSV.
| 44. INSTALL RADIATOR ASSEMBLY |
Install the radiator with the 4 bolts.
Attach the 4 clamps to side of the radiator assembly.
Connect the 2 airbag sensor front connectors.
| 45. CONNECT OIL COOLER INLET HOSE |
Connect the oil cooler inlet hose to the radiator assembly.
| 46. CONNECT OIL COOLER OUTLET HOSE |
Connect the oil cooler outlet hose to the radiator assembly.
| 47. INSTALL FAN PULLEY |
| 48. INSTALL FAN SHROUD |
![]() |
Install the fan pulley to the water pump.
Place the shroud together with the fluid coupling fan between the radiator and engine.
Install the coupling fan to the water pump with the 4 nuts. Tighten the nuts as much as possible by hand.
Attach the shroud's claws to the radiator as shown in A in the illustration.
Install the shroud with the 2 bolts.
Connect the reservoir hose to the radiator tank upper.
Install the drive belt (Click here).
Tighten the 4 nuts of the fluid coupling fan.
| 49. INSTALL DRIVE BELT |
![]() |
Install the drive belt to all the pulleys except the drive belt tensioner pulley.
Use the hexagon-shaped part indicated by the arrow in the illustration to move the tensioner pulley downward and then install the drive belt to the tensioner pulley.
![]() |
After a new belt has been installed, check that the tensioner indicator mark is within range A shown in the illustration.
| 50. CONNECT RADIATOR OUTLET HOSE |
| 51. CONNECT RADIATOR INLET HOSE |
| 52. INSTALL RADIATOR GRILLE |
Attach the 6 claws to install the radiator grille.
Install the 2 screws and 2 clips.
| 53. INSTALL INTAKE AIR CONNECTOR AND AIR CLEANER ASSEMBLY |
![]() |
Install the air cleaner and intake air connector assembly with the 4 bolts, and tighten the hose clamp.
Connect the MAF meter connector and harness clamps.
Connect the No. 2 ventilation hose.
Connect the vacuum hose.
| 54. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 55. ADD ENGINE OIL |
Clean and install the oil drain plug with a new gasket.
Add fresh engine oil.
| Item | Specified Condition |
| Drain and refill with oil filter change | 5.6 liters (5.9 US qts, 4.9 Imp. qts) |
| Drain and refill without oil filter change | 5.3 liters (5.6 US qts, 4.6 Imp. qts) |
| Dry fill | 6.3 liters (6.7 US qts, 5.5 Imp. qts) |
Install the oil filler cap.
| 56. ADD ENGINE COOLANT |
Tighten all the plugs and fill the radiator with TOYOTA Super Long Life Coolant (SLLC).
Fill the radiator with TOYOTA SLLC to the F line.
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the F line, add TOYOTA SLLC to the F line.
Install the radiator cap.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2,500 to 3,000 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
![]() |
Check the coolant level in the radiator reservoir.
If the coolant level is below the L line, add SLLC to the reservoir F line.
| 57. ADD AUTOMATIC TRANSMISSION FLUID |
| 58. INSPECT AUTOMATIC TRANSMISSION FLUID |
| 59. INSPECT FOR FUEL LEAK |
Check that there are no fuel leaks after performing maintenance anywhere on the fuel system.
If there are fuel leaks, repair or replace parts as necessary.
| 60. INSPECT FOR OIL LEAK |
Start the engine, and check that there are no oil leaks after performing maintenance.
| 61. INSPECT FOR FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17.1 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the cylinder block and head.
| 62. INSTALL NO. 1 ENGINE UNDER COVER |
Install the No. 1 under cover with the 4 bolts.
Install the side cover RH with the 3 clips and 3 bolts.
Install the side cover LH with the 3 clips and 3 bolts.
| 63. INSPECT IGNITION TIMING |
Warm up the engine and stop the engine.
![]() |
When using the intelligent tester:
Check the ignition timing.
Connect the intelligent tester to the DLC3.
Start the engine and idle the engine.
Turn the intelligent tester main switch ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.
![]() |
When not using the intelligent tester:
Check the ignition timing.
Using SST, connect a tachometer tester probe to terminal 9 (TAC) of the DLC3.
![]() |
Clamp a timing light tester probe to the No. 1 cylinder ignition coil connector's 4 lead wires or green-red lead wire.
Start the engine.
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
![]() |
![]() |
Using a timing light, measure the ignition timing.
Remove SST from terminals 13 (TC) and 4 (CG) of the DLC3.
Check the ignition timing.
Confirm that the ignition timing moves to the advanced angle side when the engine speed is increased.
Remove the timing light.
| 64. CHECK IDLE SPEED |
Warm up and stop the engine.
When using the intelligent tester:
Check the idle speed.
![]() |
Connect the intelligent tester to the DLC3.
Start the engine and idle the engine.
Turn the intelligent tester main switch ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine SPD.
![]() |
When not using the intelligent tester:
Check the idle speed.
Using SST, connect a tachometer tester probe to terminal 9 (TAC) of the DLC3.
Start the engine and idle the engine.
Check the idle speed.
| 65. CHECK CO/HC |
Start and warm up the engine.
Run the engine at 2,500 rpm for approximately 180 seconds and idle the engine.
![]() |
Insert a CO/HC meter testing probe at least 40 cm (1.3 ft.) into the tailpipe.
Check the CO/HC concentration at idle.
If the CO/HC concentration is not as specified, perform troubleshooting in the order given below.
Check the heated oxygen sensor operation (Click here).
See the table below for possible causes, and then inspect and repair the applicable causes as necessary.
| CO | HC | Problems | Causes |
| Normal | High | Rough idle |
|
| Low | High | Rough idle (Fluctuating HC reading) |
|
| High | High | Rough idle (Black smoke from exhaust) |
|
| 66. CHECK FUNCTION OF THROTTLE BODY |
![]() |
Check the throttle control motor operating sound.
Turn the ignition switch ON.
When pressing the accelerator pedal, check the operating sound of the running motor. Make sure that no friction noises emit from the motor.
If friction noise is heard, replace the throttle body.
![]() |
Check the throttle position sensor.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Under Current Data, check that the throttle valve opening percentage (Throttle Pos) is within the standard.