ENGINE ASSEMBLY > REMOVAL |
| 1. DISCHARGE FUEL SYSTEM PRESSURE |
Disconnect the cable from the negative (-) battery terminal.
Remove the front driver side scuff plate.
Using a screwdriver, detach the 7 claws.
Using a clip remover, detach the 3 clips and remove the scuff plate.
![]() |
Fold back the floor carpet and disconnect the joining connector, as shown in the illustration.
Connect the cable to the negative (-) battery terminal.
Start the engine. After the engine has stopped on its own, turn the ignition switch OFF.
Crank the engine again, and then check that the engine does not start.
Loosen the fuel tank cap, and then discharge the pressure in the fuel tank completely.
Connect the fuel pump connector.
Install the front driver side scuff plate.
Clear the DTCs (Click here).
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE NO. 1 ENGINE UNDER COVER |
Remove the 4 bolts and under cover.
Remove the 3 clips, 3 bolts and side cover LH.
Remove the 3 clips, 3 bolts and side cover RH.
| 4. DRAIN ENGINE COOLANT |
Remove the radiator cap.
Loosen the cylinder block drain cock plug and radiator drain cock plug, and then drain the coolant.

| 5. DRAIN ENGINE OIL |
Remove the oil filler cap.
Remove the oil drain plug and drain the oil into a container.
| 6. DRAIN MANUAL TRANSMISSION OIL (for Manual Transmission) |
Remove the drain plug and gasket to drain the oil.
Install a new gasket and the drain plug.
| 7. DRAIN AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission) |
Remove the drain plug and gasket, and drain ATF.
Install a new gasket and the drain plug.
| 8. REMOVE INTAKE AIR CONNECTOR AND AIR CLEANER ASSEMBLY |
![]() |
Disconnect the vacuum hose.
Disconnect the No. 2 ventilation hose.
Disconnect the MAF meter connector and wire harness clamps.
Loosen the hose clamp and remove the 4 bolts, air cleaner and intake air connector assembly.
| 9. REMOVE RADIATOR GRILLE |
![]() |
Remove the 2 clips and 2 screws.
![]() |
Put protective tape around the radiator grille.
| *1 | Protective Tape |
Detach the 6 claws and remove the radiator grille.
| 10. DISCONNECT RADIATOR INLET HOSE |
| 11. DISCONNECT RADIATOR OUTLET HOSE |
| 12. REMOVE DRIVE BELT |
![]() |
Use the hexagon-shaped part indicated by the arrow in the illustration to move the tensioner pulley downward and decrease the tension in the drive belt. Then remove the drive belt.
| 13. REMOVE FAN SHROUD |
![]() |
Disconnect the reservoir hose from the radiator tank upper.
Loosen the 4 nuts holding the fluid coupling fan.
Remove the drive belt (Click here).
Remove the 2 bolts holding the fan shroud.
Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan.
Remove the fan pulley from the water pump.
| 14. REMOVE FAN PULLEY |
| 15. DISCONNECT OIL COOLER INLET HOSE (for Automatic Transmission) |
Disconnect the oil cooler inlet hose from the radiator assembly.
| 16. DISCONNECT OIL COOLER OUTLET HOSE (for Automatic Transmission) |
Disconnect the oil cooler outlet hose from the radiator assembly.
| 17. REMOVE RADIATOR ASSEMBLY |
Disconnect the 2 airbag sensor front connectors.
![]() |
Using a clip remover, detach the 4 clamps from the side of radiator assembly as shown in the illustration.
![]() |
Remove the 4 bolts and radiator assembly.
| 18. DISCONNECT HOSE |
![]() |
Disconnect the vacuum hose from the intake manifold.
for Unleaded Gasoline Specification Vehicle:
Disconnect the hose from the purge VSV.
| 19. DISCONNECT FUEL HOSE |
![]() |
Disconnect the No. 2 fuel hose from the pressure regulator.
Disconnect the No. 1 fuel hose from the pulsation damper.
Detach the lock claw by lifting up the cover, as shown in the illustration.
Check for foreign matter on the pipe and around the connector before disconnecting. Clean if necessary.
![]() |
Disconnect the pipe from he connector.
If the connector and the pipe are stuck together, pinch the connector, and push and pull the pipe to disconnect them.
Check for foreign matter on the seal surface of the disconnected pipe. Clean if necessary.
![]() |
To protect the disconnected pipe and connector from damage and contamination, cover it with a plastic bag.
| 20. DISCONNECT ENGINE WIRE |
![]() |
Disconnect the ECM connectors.
Remove the glove compartment door.
Disconnect the 4 ECM connectors.
Remove the bolt and clamp, and disconnect the ground wire.
Remove the bolt and disconnect the ground wire from the frame.
Pull out the engine wire from the cabin.
![]() |
Remove the engine room relay block cover (upper).
Remove the engine room relay block cover (side).
Using a screwdriver, detach the 4 claws and remove the relay block cover.
Remove the nut and disconnect the cable from the engine room junction block.
Disconnect the 2 engine room junction block connectors and disconnect the wire clamp.
Remove the bolt and disconnect the wire clamp from the front engine mounting bracket LH.
Remove the bolt and disconnect the sensor clamp.
| 21. DISCONNECT VANE PUMP |
![]() |
Disconnect the oil pressure switch connector.
Remove the 2 bolts and disconnect the vane pump from the engine.
Support the vane pump securely.
| 22. REMOVE OIL DIPSTICK |
Remove the bolt, dipstick guide and O-ring.
| 23. REMOVE OIL DIPSTICK GUIDE |
| 24. DISCONNECT COOLER COMPRESSOR FROM ENGINE |
Disconnect the compressor connector.
![]() |
Remove the 2 bolts and disconnect the suction hose from the engine.
![]() |
Remove the 4 bolts and disconnect the compressor from the engine.
Support the cooler compressor securely.
| 25. REMOVE HOOD ASSEMBLY |
![]() |
Disconnect the washer nozzle hose.
Remove the 4 bolts and hood.
| 26. REMOVE FRONT EXHAUST PIPE |
Remove the 2 bolts and 2 compression springs.
Disconnect the front pipe from the exhaust manifold and remove the gasket.
Remove the front pipe from the pipe support.
| 27. REMOVE FRONT PROPELLER SHAFT ASSEMBLY |
![]() |
Place matchmarks on the yoke and differential flange.
Remove the 4 nuts, 4 bolts and 4 washers, and disconnect the propeller shaft.
![]() |
Place matchmarks on the yoke and transfer flange.
Remove the 4 nuts, 4 washers and front propeller shaft.
| 28. REMOVE REAR PROPELLER SHAFT ASSEMBLY |
![]() |
Place matchmarks on the propeller shaft flange and transfer flange.
Remove the 4 nuts and 4 washers, and disconnect the propeller shaft.
![]() |
Place matchmarks on the propeller shaft flange and differential flange.
Remove the 4 nuts, 4 bolts and 4 washers.
Remove the propeller shaft.
| 29. REMOVE STARTER |
![]() |
Disconnect the starter connector.
Disconnect the terminal cap.
Remove the nut and disconnect the starter wire.
Remove the 2 bolts and starter.
| 30. REMOVE CLUTCH RELEASE CYLINDER (for Manual Transmission) |
![]() |
Remove the 2 bolts and clutch release cylinder.
| 31. REMOVE MANUAL TRANSMISSION UNIT (for Manual Transmission) |
| 32. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission) |
| 33. REMOVE CLUTCH COVER (for Manual Transmission) |
![]() |
Place matchmarks on the clutch cover and flywheel.
Loosen each set bolt one turn at a time until spring tension is released.
Remove the 6 set bolts and pull off the clutch cover.
| 34. REMOVE CLUTCH DISC (for Manual Transmission) |
| 35. REMOVE FLYWHEEL (for Manual Transmission) |
![]() |
Fix the crankshaft in place with SST.
![]() |
Remove the 10 bolts and flywheel.
| 36. REMOVE DRIVE PLATE (for Automatic Transmission) |
![]() |
Fix the crankshaft in place with SST.
![]() |
Remove the 10 bolts, rear drive plate spacer, drive plate and front drive plate spacer.
| 37. REMOVE REAR END PLATE |
Remove the bolt and rear end plate.
| 38. REMOVE ENGINE ASSEMBLY |
![]() |
Install the 2 engine hangers as shown in the illustration.
| Item | Part No. |
| Engine hanger | 12281-0C010 |
| Bolt | 90105-T0129 |
Attach the engine sling device and chain block to the engine hangers.
![]() |
Remove the 4 bolts and 4 nuts holding the engine mounting bracket and frame.
![]() |
Lift the engine out of the vehicle slowly and carefully.
| 39. INSTALL ENGINE TO ENGINE STAND |
Place the engine assembly onto the stand.
| 40. REMOVE IGNITION COIL |
Disconnect the 4 ignition coil connectors and remove the 4 bolts and 4 ignition coils.
| 41. REMOVE SPARK PLUG |
| 42. REMOVE VENTILATION PIPE |
Remove the bolt and ventilation pipe.
| 43. REMOVE GENERATOR |
![]() |
Detach the terminal cap.
Remove the nut, bolt and generator wire.
Disconnect the generator connector.
Remove the 2 bolts and generator.
| 44. REMOVE ENGINE WIRE |
Disconnect the oil pressure sensor connector.
Disconnect the noise filter connector.
Disconnect the camshaft position sensor connector.
Disconnect the 4 injector connectors.
Disconnect the crankshaft position sensor connector.
Disconnect the oil control valve connector.
for Unleaded Specification Vehicle:
Disconnect the purge VSV connector.
Disconnect the throttle body connector.
Disconnect the engine coolant temperature sensor connector.
Disconnect the knock sensor connector.
Disconnect the wire harness from the clamps.
Remove the 2 bolts and wire harness from the engine.
| 45. REMOVE THROTTLE BODY |
Disconnect the throttle position sensor and control motor connector.
Disconnect the 2 water by-pass hoses.
![]() |
Remove the 2 bolts, 2 nuts and throttle body.
Remove the gasket.
| 46. REMOVE FUEL DELIVERY PIPE |
![]() |
Disconnect the 4 clamps and wire harness from the delivery pipe.
Disconnect the vacuum hose.
![]() |
Disconnect the 4 injector connectors.
Remove the 2 bolts and delivery pipe together with the 4 injectors.
![]() |
Using 2 screwdrivers, pry out the 4 spacers from the cylinder head.
| 47. REMOVE INJECTOR |
![]() |
Pull out the 4 injectors from the delivery pipe.
| 48. REMOVE INTAKE MANIFOLD |
![]() |
Disconnect the crankshaft position sensor from the clamp.
Remove the 5 bolts, 2 nuts, intake manifold and gasket.
| 49. REMOVE EXHAUST MANIFOLD HEAT INSULATOR |
![]() |
Remove the 5 bolts and heat insulator.
| 50. REMOVE EXHAUST MANIFOLD |
![]() |
Remove the 6 nuts, exhaust manifold and gasket.
| 51. REMOVE IDLE PULLEY ASSEMBLY |
![]() |
Loosen the bolt, and then remove the idle pulley assembly.
| 52. REMOVE COMPRESSOR MOUNTING BRACKET |
![]() |
Remove the 5 bolts and compressor mounting bracket.
| 53. REMOVE V-RIBBED BELT TENSIONER |
![]() |
Remove the 3 bolts and belt tensioner.
| 54. REMOVE WATER INLET |
Remove the bolt, 2 nuts, water inlet and gasket.
| 55. REMOVE THERMOSTAT |
Remove the thermostat and gasket.
| 56. REMOVE NO. 1 IDLER PULLEY |
![]() |
Remove the bolt, pulley plate, idler pulley and spacer.
| 57. REMOVE ENGINE OIL PRESSURE SWITCH |
Using a 24 mm deep socket wrench, remove the oil pressure switch.
| 58. REMOVE NO. 1 WATER BY-PASS PIPE |
![]() |
Remove the 2 nuts, water by-pass pipe and gasket.
| 59. REMOVE KNOCK SENSOR |
Remove the bolt and sensor.
| 60. REMOVE ENGINE COOLANT TEMPERATURE SENSOR |
Using a 19 mm deep socket wrench, remove the sensor and gasket.
| 61. REMOVE CAMSHAFT POSITION SENSOR |
![]() |
Remove the bolt, sensor and O-ring.
| 62. REMOVE CRANKSHAFT POSITION SENSOR |
![]() |
Disconnect the sensor connector.
Disconnect the connector from the connector bracket.
Detach the harness clamp.
Remove the bolt and sensor.
| 63. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE |
![]() |
Remove the bolt, oil control valve and O-ring.
| 64. REMOVE FRONT ENGINE MOUNTING BRACKET RH |
![]() |
Remove the 4 bolts and mounting bracket.
| 65. REMOVE FRONT ENGINE MOUNTING BRACKET LH |
![]() |
Remove the 4 bolts and mounting bracket.