Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0500/42    Vehicle Speed Sensor "A"

for Preparation Click here


DESCRIPTION

The vehicle speed sensor outputs a 4 pulse signal for every revolution of the rotor shaft, which is rotated by the transmission output shaft via the driven gear. After this signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter, it is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of these pulse signals.

G036498E01


DTC No.
DTC Detection Condition
Suspected Area
P0500/42
While the vehicle is being driven, no vehicle speed sensor signal to the ECM
(2 trip detection logic)
  1. Open or short in speed sensor circuit
  2. Vehicle speed sensor
  3. Combination meter
  4. ECM

MONITOR DESCRIPTION

  1. The ECM assumes that the vehicle is being driven when the vehicle speed signal from the transmission (SP2) indicates a speed of 9 km/h (6 mph) or more.
    If there is no vehicle speed signal from the combination meter (SP1) for 5 seconds when the vehicle is being driven, the ECM determines this to be a malfunction of the vehicle speed sensor. The ECM then illuminates the MIL and stores the DTC.

WIRING DIAGRAM


A256001E04


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK OPERATION OF SPEEDOMETER
  1. Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

    HINT:
    1. The vehicle speed sensor is operating normally if the speedometer reading is normal.
    2. If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction.



NG
GO TO MALFUNCTION IN SPEEDOMETER
OK


2.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Vehicle Speed.

  1. Drive the vehicle.

  1. Read the value displayed on the tester.

    OK:
    Vehicle speeds displayed on tester and speedometer display are equal.



NG
Go to step 3
OK

CHECK FOR INTERMITTENT PROBLEMS 

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
G034704E09
  1. Disconnect the combination meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    C27-6 - E9-8 (SPD)
    Below 1 Ω
    C27-6 or E9-8 (SPD) - Body ground
    10 kΩ or higher

    HINT:
    If the wire has a short, check the speed signal circuit in other systems related to the vehicle speed signal (e.g. tire pressure warning system, audio system, etc.).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (OTHER SYSTEM RELATED TO SPEED METER)
OK


4.CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE)
A127854E51
  1. Disconnect the combination meter connector.

    HINT:
    Disconnect the ECU connectors on the other systems related to the speed signal (but the ECM connectors must be connected).

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    C27-6 - Body ground
    Ignition switch on
    4.5 to 5.5 V



NG
REPLACE ECM
OK


5.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL OUTPUT WAVEFORM)
A261267E05
  1. Remove the combination meter assembly.

  1. Connect the combination meter connector.

  1. Move the shift lever to the neutral position.

  1. Jack up one of the rear wheels.

  1. Turn the ignition switch to ON.

  1. Check the voltage between the terminal of the combination meter and the body ground while the rear wheel is turned slowly.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    C27-6 - Body ground
    Ignition switch on
    Turn wheel slowly
    Voltage generated intermittently

    HINT:
    1. The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.
    2. A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly.

    HINT:
    The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.



NG
Go to step 6
OK

REPLACE ECM 

6.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM)
A261267E06
  1. Remove the combination meter assembly.

  1. Connect the combination meter connector.

  1. Move the shift lever to the neutral position.

  1. Jack up one of the rear wheels.

  1. Turn the ignition switch to ON.

  1. Check the voltage between the terminal of the combination meter and the body ground while the rear wheel is turned slowly.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    C27-5 - Body ground
    Ignition switch on
    Turn wheel slowly
    Voltage generated intermittently

    HINT:
    The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.



NG
Go to step 7
OK

REPLACE COMBINATION METER ASSEMBLY 

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - SPEEDOMETER SENSOR)
A240431E06
  1. Disconnect the combination meter connector.

  1. Disconnect the speedometer sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C27-5 - S3-3 (SI)
    Always
    Below 1 Ω
    C27-5 or S3-3 (SI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SPEEDOMETER SENSOR