Home › ENGINE · 5L-E › ENGINE CONTROL SYSTEM › ECD SYSTEM

ECD SYSTEM > ECM Power Source Circuit

for Preparation Click here


DESCRIPTION

When the ignition switch is turned ON, the battery voltage is applied to terminal IGSW of the ECM. The ECM "MREL" output signal causes current to flow to the MAIN relay coil, closing the contacts of the EFI relay and supplying power to terminal +B of the ECM.

WIRING DIAGRAM


A137681E01


INSPECTION PROCEDURE

1.CHECK ECM (+B VOLTAGE)
A062416E66
  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    E23-12 (+B) - E20-14 (E1)
    9 to 14 V



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
A062420E09
  1. Disconnect the E20 ECM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E20-14 (E1) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK ECM (IGSW VOLTAGE)
A062416E67
  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    E23-14 (IGSW) - E20-14 (E1)
    9 to 14 V



OK
Go to step 6
NG


4.INSPECT FUSE (IGN)
A310678E01
  1. Remove the IGN fuse from the instrument panel junction block.

  1. Measure the resistance of the IGN fuse.

    Standard resistance:
    Tester Connection
    Specified Condition
    IGN fuse
    Below 1 Ω



NG
CHECK FOR SHORT IN ALL HARNESSES AND COMPONENTS CONNECTED TO FUSE
OK


5.INSPECT IGNITION SWITCH ASSEMBLY
A087913E02
  1. Disconnect the I8 ignition switch connector.

  1. Measure the resistance of the ignition switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (AM2) - 6 (IG2)
    LOCK
    10 kΩ or higher
    5 (AM2) - 6 (IG2)
    ON
    Below 1 Ω



NG
REPLACE IGNITION SWITCH ASSEMBLY
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH, IGNITION SWITCH - ECM) 

6.CHECK ECM (MREL VOLTAGE)
A062416E68
  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    E23-3 (MREL) - E20-14 (E1)
    9 to 14 V



NG
REPLACE ECM
OK


7.INSPECT FUSE (EFI)
A121707E01
  1. Remove the EFI fuse from the engine room junction block.

  1. Measure the resistance of the EFI fuse.

    Standard resistance:
    Tester Connection
    Specified Condition
    EFI fuse
    Below 1 Ω



NG
CHECK FOR SHORT IN ALL HARNESSES AND COMPONENTS CONNECTED TO FUSE
OK


8.CHECK INTEGRATION NO.1 RELAY (MAIN RELAY)
G034717E03
  1. Disconnect the 1J integration relay connector from the engine room junction block .

  1. Measure the voltage of the integration relay.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    1J-4 - Body ground
    Ignition switch ON
    10 to 14 V



NG
REPLACE INTEGRATION NO.1 RELAY
OK


9.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY [MAIN RELAY] - ECM AND BODY GROUND)
A106817E05
  1. Disconnect the 1J integration relay connector from the engine room junction block .

  1. Disconnect the E23 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    1J-2 - E23-3 (MREL)
    Below 1 Ω
    1J-4 - E23-12 (+B)
    Below 1 Ω
    1J-3 - Body ground
    Below 1 Ω
    1J-2 or E23-3 (MREL) - Body ground
    10 kΩ or higher
    1J-4 or E23-12 (+B) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (TERMINAL +B OF ECM - BATTERY)