DTC P2121/19 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2121/19 | Either of following conditions 1 or 2 met for 0.5 seconds (1 trip detection logic)
|
|
| 1.READ DATA LIST (ACCELERATOR POSITION NO. 1, ACCELERATOR POSITION NO. 2) |
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Accelerator Position No. 1 and Accelerator Position No. 2.
Read the values.
| Accelerator Pedal | Accelerator Position No. 1 | Accelerator Position No. 2 |
| Released | 0.5 to 1.1 V | 1.2 to 2.0 V |
| Depressed | 2.6 to 4.5 V | 3.4 to 4.75 V |
|
| ||||
| NG | |
| 2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM) |
![]() |
Disconnect the A22 accelerator pedal position sensor connector.
Disconnect the E8 ECM connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| A22-6 (VPA) - E8-18 (VPA) | Below 1 Ω |
| A22-5 (EPA) - E8-20 (EPA) | Below 1 Ω |
| A22-4 (VCPA) - E8-26 (VCPA) | Below 1 Ω |
| A22-3 (VPA2) - E8-19 (VPA2) | Below 1 Ω |
| A22-2 (EPA2) - E8-21 (EPA2) | Below 1 Ω |
| A22-1 (VCP2) - E8-27 (VCP2) | Below 1 Ω |
| A22-6 (VPA) or E8-18 (VPA) - Body ground | 10 kΩ or higher |
| A22-5 (EPA) or E8-20 (EPA) - Body ground | 10 kΩ or higher |
| A22-4 (VCPA) or E8-26 (VCPA) - Body ground | 10 kΩ or higher |
| A22-3 (VPA2) or E8-19 (VPA2) - Body ground | 10 kΩ or higher |
| A22-2 (EPA2) or E8-21 (EPA2) - Body ground | 10 kΩ or higher |
| A22-1 (VCP2) or E8-27 (VCP2) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 1.CHECK ECM (VPA, VPA2 VOLTAGE) |
![]() |
Turn the ignition switch ON.
Measure the voltage of the ECM connector.
| Tester Connection | Accelerator Pedal Condition | Specified Condition |
| E8-18 (VPA) - E8-20 (EPA) | Released | 0.5 to 1.1 V |
| E8-18 (VPA) - E8-20 (EPA) | Depressed | 2.6 to 4.5 V |
| E8-19 (VPA2) - E8-21 (EPA2) | Released | 1.2 to 2.0 V |
| E8-19 (VPA2) - E8-21 (EPA2) | Depressed | 3.4 to 4.75 V |
|
| ||||
| NG | |
| 2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM) |
![]() |
Disconnect the A22 accelerator pedal position sensor connector.
Disconnect the E8 ECM connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| A22-6 (VPA) - E8-18 (VPA) | Below 1 Ω |
| A22-5 (EPA) - E8-20 (EPA) | Below 1 Ω |
| A22-4 (VCPA) - E8-26 (VCPA) | Below 1 Ω |
| A22-3 (VPA2) - E8-19 (VPA2) | Below 1 Ω |
| A22-2 (EPA2) - E8-21 (EPA2) | Below 1 Ω |
| A22-1 (VCP2) - E8-27 (VCP2) | Below 1 Ω |
| A22-6 (VPA) or E8-18 (VPA) - Body ground | 10 kΩ or higher |
| A22-5 (EPA) or E8-20 (EPA) - Body ground | 10 kΩ or higher |
| A22-4 (VCPA) or E8-26 (VCPA) - Body ground | 10 kΩ or higher |
| A22-3 (VPA2) or E8-19 (VPA2) - Body ground | 10 kΩ or higher |
| A22-2 (EPA2) or E8-21 (EPA2) - Body ground | 10 kΩ or higher |
| A22-1 (VCP2) or E8-27 (VCP2) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||