Home › SUSPENSION & AXLE › AXLE › REAR AXLE SHAFT

REAR AXLE SHAFT > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.



2. REMOVE REAR WHEEL


3. DRAIN BRAKE FLUID

NOTICE:
Wash off brake fluid immediately if it comes in contact with any painted surface.



4. DISCONNECT BRAKE LINE


    C111505
  1. Using a union nut wrench, disconnect the brake line.

  1. Remove the 2 bolts and cylinder.



5. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY
  1. Release the parking brake lever, and remove the drum and gasket.

    HINT:
    If the drum cannot be removed easily, perform the following procedures.



    C111496E01
  1. Remove the hole plug (adjust) and insert a screwdriver into the hole on the backing plate, and hold the automatic adjust lever away from the adjuster.

  1. Using another screwdriver, compress the shoe adjuster by turning the adjusting wheel.



6. REMOVE REAR SPEED SENSOR LH (w/ ABS, VSC)


  1. Disconnect the connector.


    C189956E01

  1. Detach the connector.

  1. Detach the 3 clamps.

  1. Remove the bolt and speed sensor.

    NOTICE:
    Keep the sensor tip and sensor installation hole free from foreign matter.



7. REMOVE BRAKE SHOES


    C111498
  1. Using pliers, remove the shoe hold down springs and pins from the front brake shoe and rear brake shoe.



    C113223
  1. Push the front or rear side of the wheel brake cylinder with the brake shoe. Then remove the side of the brake shoe opposite to the side of the cylinder being pushed. Finally, remove the remaining side of the brake shoe.

    NOTICE:
    Be careful not to damage the cylinder dust boot.



    C123256
  1. Move one of the shoes downward and remove the shoe tension spring.



    C123253
  1. Remove the front and rear brake shoes.

  1. Remove the strut set and return spring from the shoe.

  1. Remove the support clip from the strut set and return spring.



    C111502
  1. Using needle-nose pliers, disconnect the No. 3 parking brake cable from the parking brake shoe lever.



8. DISCONNECT PARKING BRAKE CABLE
  1. Remove the 2 bolts and disconnect the parking brake cable.



9. REMOVE REAR AXLE SHAFT WITH BACKING PLATE


C191121
  1. Remove the 4 nuts.

  1. Pull out the axle shaft from the axle housing.



10. REMOVE O-RING
  1. Remove the O-ring from the axle housing.



11. REMOVE REAR AXLE SHAFT OIL SEAL LH


C118307E02
  1. Using SST, tap out the oil seal.

    SST
    09308-00010  

    NOTICE:
    Be careful not to damage the axle housing hole.



12. REMOVE BACKING PLATE TO REAR AXLE HOUSING SETTING BOLT


C190684
  1. Temporarily install 4 nuts to the setting bolts.

    NOTICE:
    Do not use any nuts removed from the vehicle, as they may be damaged.

  1. Using a hammer, tap out the 4 setting bolts from the backing plate.

  1. Remove the 4 nuts and 4 setting bolts.



13. REMOVE REAR AXLE BEARING INNER RETAINER LH AND REAR SKID CONTROL ROTOR (w/ ABS, VSC)


C190685
  1. Grind the retainer and skid control rotor surfaces using a grinder, and then pry them off with a chisel and hammer.

    NOTICE:
    Be careful not to damage the axle shaft.



14. REMOVE REAR AXLE BEARING INNER RETAINER LH


C190686
  1. Using a snap ring expander, remove the snap ring.



    C190689
  1. Grind the retainer surface using a grinder, and then pry it off with a chisel and hammer.

    NOTICE:
    Be careful not to damage the axle shaft.

  1. Remove the shaft washer from the axle shaft.



15. REMOVE REAR AXLE SHAFT LH
  1. Insert the setting bolts into the backing plate and temporarily install washers and nuts to the setting bolts. Tighten the nuts to temporarily install the setting bolts to the backing plate and bearing case.

  1. Remove the nuts and washers from the setting bolts.



    C190687E01
  1. Install SST to the backing plate with the 4 nuts.

    SST
    09521-25011  



    C190688E01
  1. Using SST and a press, press out the axle shaft.

  1. Remove the 4 nuts and SST.

  1. Temporarily install 4 nuts to the setting bolts.

    NOTICE:
    Do not use any nuts removed from the vehicle, as they may be damaged.

  1. Using a hammer, tap out the 4 setting bolts from the backing plate.

  1. Remove the 4 nuts and 4 setting bolts.



16. REMOVE REAR AXLE HUB BOLT LH


    C191008E01
  1. Using SST, remove the 6 hub bolts.

    SST
    09650-17011  

  1. Remove the deflector and gasket from the axle shaft.

    NOTICE:
    1. Do not deform the deflector.
    2. Make sure to align the groove of SST with the flange of the oil deflector.



17. INSPECT REAR AXLE SHAFT LH


F050876E01
  1. Using a dial indicator, measure the rear axle shaft shaft runout and flange runout.

    Maximum runout:
    Item
    Specified Condition
    Shaft runout
    1.5 mm (0.0591 in.)
    Flange runout
    0.10 mm (0.00394 in.)

    If the rear axle shaft or flange is damaged or worn, or if the runout is greater than the maximum, replace the rear axle shaft.



18. REMOVE REAR AXLE SHAFT OUTER OIL SEAL


C190691E01
  1. Using SST, tap out the outer oil seal.

    SST
    09308-00010  



19. REMOVE REAR AXLE SHAFT BEARING LH


C190692E01
  1. Using SST and a press, press out the bearing.

    SST
    09223-56010  
    09950-60010   (09951-00640)