BRAKE BOOSTER (w/ VSC) > INSTALLATION |
| 1. INSTALL BRAKE BOOSTER ASSEMBLY |
Install a new gasket to the brake booster.
![]() |
Install the booster with the 4 nuts.
Install the push rod clevis.
Apply a light coat of lithium soap base glycol grease to the clevis pin.
![]() |
Install the clevis pin and a new clip.
Install the return spring.
Install the check valve and grommet to the booster.
Connect the vacuum hose with the clip.
Install the vacuum warning switch grommet to the brake booster.
Install the vacuum warning switch to the booster and connect the vacuum warning switch connector.
| 2. CHECK AND ADJUST BRAKE BOOSTER PUSH ROD |
![]() |
Set SST on the master cylinder, and then lower the pin until its tip slightly touches the piston.
![]() |
Turn SST upside down, and then set it on the booster.
Measure the clearance between the booster push rod and pin head (SST).
![]() |
To adjust the clearance of the rod, first depress the pedal so that the rod protrudes. Then fix the rod in place using SST and rotate the hexagon cap nut to adjust the clearance.
| 3. INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY |
Install the brake master cylinder (Click here).
| 4. FILL RESERVOIR WITH BRAKE FLUID |
| 5. BLEED AIR FROM BRAKE MASTER CYLINDER |
![]() |
Using a union nut wrench, disconnect the 2 brake lines from the master cylinder.
Slowly depress and hold the brake pedal.
![]() |
Cover the outer holes with your fingers, and release the pedal.
Repeat the 2 previous steps 3 or 4 times.
Using a union nut wrench, connect the 2 brake lines to the master cylinder.
| 6. BLEED AIR FROM BRAKE LINE |
Remove the bleeder plug cap.
Connect a vinyl tube to the bleeder plugs.
Depress the pedal several times, and then loosen the bleeder plug with the pedal depressed.
When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.
Repeat the 2 previous steps until all the air in the brake fluid is gone.
Tighten the bleeder plug.
Install the cap.
![]() |
Bleed air from the brake line for each wheel by repeating the above procedures.
| 7. BLEED AIR FROM CLUTCH LINE (for Manual Transmission) |
Remove the brake master cylinder reservoir filler cap assembly.
Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the clutch line.
Remove the bleeder plug cap.
![]() |
Connect a vinyl tube to the bleeder plug.
Depress the clutch pedal several times, and then loosen the bleeder plug with the pedal depressed.
At the point when fluid stops coming out, tighten the bleeder plug, and then release the clutch pedal.
Repeat the previous 2 steps until all the air in the fluid is completely bled out.
Tighten the bleeder plug.
Install the bleeder plug cap.
Check that all the air has been bled out of the clutch line.
Check for brake fluid leaks.
Check the brake fluid level in the reservoir.
w/ VSC:
w/o VSC:
Install the brake master cylinder reservoir filler cap assembly.
| 8. CHECK AND ADJUST BRAKE PEDAL HEIGHT |
![]() |
Check the pedal height.
| Model | Specified Condition |
| for Manual Transmission | 156.9 to 166.9 mm (6.177 to 6.571 in.) |
| for Automatic Transmission | 158.1 to 168.1 mm (6.224 to 6.618 in.) |
Adjust the pedal height.
Disconnect the connector from the stop light switch.
Remove the switch.
Loosen the push rod clevis lock nut.
Adjust the pedal height by turning the push rod.
Tighten the lock nut.
![]() |
Insert the switch into the adjuster until it slightly touches the pedal.
![]() |
Turn the switch a quarter turn clockwise.
Connect the connector to the switch.
Check the switch clearance.
| 9. CHECK BRAKE PEDAL FREE PLAY |
![]() |
Stop the engine. Depress the pedal several times until there is no vacuum in the booster. Then release the pedal.
Depress the pedal until resistance is felt.
Check the pedal free play by measuring the distance between the position in the previous step and the pedal's released position.
Check the switch clearance.
| 10. CHECK BRAKE PEDAL RESERVE DISTANCE |
![]() |
Release the parking brake lever. Start the engine.
Depress the pedal and check the pedal reserve distance.
Depress the pedal with a force of 490 N (50 kgf, 110 lbf).
Measure the distance between the pedal and dash panel shown in the illustration.
| 11. CHECK BRAKE FLUID LEVEL IN RESERVOIR |
![]() |
Check the fluid level.
If the brake fluid level is lower than the MIN line, check for leaks and inspect the disc brake pads. If necessary, refill the reservoir with brake fluid to the MAX line after repair or replacement.
| 12. CHECK FOR BRAKE FLUID LEAK |
| 13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 14. CHECK SRS WARNING LIGHT |
Check SRS warning light (Click here).