Home › DRIVE LINE › DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY

FRONT DIFFERENTIAL CARRIER ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY
  1. Install the front No. 3 differential support with the 2 bolts.

    Torque:
    108 N*m{ 1100 kgf*cm , 80 ft.*lbf }

  1. Install the front No. 2 mounting support with the 2 bolts.

    Torque:
    160 N*m{ 1632 kgf*cm , 118 ft.*lbf }

  1. Install the front No. 1 mounting support with the 3 bolts.

    Torque:
    186 N*m{ 1899 kgf*cm , 137 ft.*lbf }

  1. Support the front differential with a jack.

  1. Install the 2 front mounting bolts and 2 nuts.

    Torque:
    137 N*m{ 1400 kgf*cm , 101 ft.*lbf }

  1. Install the front No. 1 differential mounting nut.

    Torque:
    87 N*m{ 889 kgf*cm , 64 ft.*lbf }

  1. Install the front differential breather tube bracket with the bolt.

    Torque:
    13 N*m{ 131 kgf*cm , 9 ft.*lbf }

  1. Lower the jack.



2. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
(Click here)


3. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



4. INSTALL FRONT PROPELLER SHAFT ASSEMBLY
(Click here)


5. ADD DIFFERENTIAL OIL


D025304E51
  1. Add differential oil so that the oil level is within 5 mm (0 to 0.196 in.) from the bottom lip of the differential filler plug hole.

    NOTICE:
    1. After changing the oil, drive the vehicle, and then check the oil level again.
    2. Too much or too little oil will lead to differential problems.

    If necessary, fill the differential carrier assembly with hypoid gear oil.

    Recommended viscosity:
    Temperature
    Viscosity
    Above -18°C (0°F)
    SAE 90
    Below -18°C (0°F)
    SAE 80W-90 or SAE 80W

    Standard oil grade:
    Item
    Specified Condition
    Front differential (4WD)
    Hypoid gear oil API GL-4 or GL-5
    Rear differential
    Hypoid gear oil API GL-5

    Standard front differential oil capacity:
    1.40 to 1.50 liters (1.48 to 1.59 US qts., 1.23 to 1.31 Imp. qts.)

    Standard rear differential oil capacity:
    Item
    Specified Condition
    Standard
    3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.90 to 2.99 Imp. qts.)
    w/ Differential lock
    2.85 to 2.95 liters (3.01 to 3.12 US qts., 2.51 to 2.60 Imp. qts.)
    Made for DANA
    2.40 to 2.50 liters (2.54 to 2.64 US qts., 2.11 to 2.20 Imp. qts.)

  1. Check for oil leakage when the oil level is low.



  1. for front differential:



      A272243E01
    1. Using SST and the 10 mm straight hexagon wrench, 10 mm union nut wrench and socket adaptor, install a new gasket and the differential filler plug.

      SST
      09961-00950  
      Text in Illustration 
      *1
      10 mm Straight Hexagon Wrench
      *2
      10 mm Union Nut Wrench
      *3
      Socket Adaptor

      Torque:
      39 N*m{ 400 kgf*cm , 29 ft.*lbf }

      NOTICE:
      1. Make sure all the tools are connected in a straight line.
      2. Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.

        Formula:
        T' = T x L3 / (L1 + L2 + L3)
        - T' = Spec. value of torque wrench
        - T = Value of specified tightening torque
        - L1 = Length of union nut wrench
        - L2 = Length of SST
        - L3 = Length of torque wrench

  1. for rear differential:

    1. Install a new gasket and the differential filler plug.

      Torque:
      49 N*m{ 500 kgf*cm , 36 ft.*lbf }



6. INSTALL NO. 2 ENGINE UNDER COVER
  1. Install the under cover with the 4 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



7. INSTALL NO. 1 ENGINE UNDER COVER
  1. Install the under cover with the 8 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }