DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock) > REASSEMBLY |
| 1. ASSEMBLE DIFFERENTIAL CASE |
![]() |
Install the side gear thrust washer to the side gear.
Install the 4 rear differential pinion gear thrust washers to the 4 rear drive pinion gears.
Install the 4 rear differential pinion gear thrust washers and 4 rear drive pinion gears to the spider.
Secure the differential case RH.
![]() |
Install the rear differential side gear and rear differential spider to the differential case RH.
![]() |
Using a dial indicator, measure the differential case RH backlash while holding the pinion toward the case.
Remove the rear differential spider from the differential case RH.
![]() |
Install the rear differential side gear and rear differential spider to the differential case LH.
Using a dial indicator, measure the differential case LH backlash while holding the pinion toward the case.
| Thickness mm (in.) | Thickness mm (in.) |
| 0.88 to 0.92 (0.0347 to 0.0362) | 1.18 to 1.22 (0.0465 to 0.0480) |
| 0.98 to 1.02 (0.0386 to 0.0401) | 1.28 to 1.32 (0.0504 to 0.0519) |
| 1.08 to 1.12 (0.0426 to 0.0440) | - |
![]() |
Align the matchmarks and assemble the RH and LH cases.
| *1 | Matchmark |
Using a plastic-faced hammer, install the differential case.
Install the 8 bolts.
Install the rear differential lock sleeve to the differential case LH.
| 2. INSTALL DIFFERENTIAL RING GEAR |
Clean the contact surfaces of the differential case and ring gear.
Heat the ring gear in boiling water that is approximately 100°C (212°F).
Carefully remove the ring gear from the boiling water.
![]() |
After the moisture on the ring gear has completely evaporated, quickly align the matchmarks on the ring gear and differential case and install the ring gear to the differential case.
| *1 | Matchmark |
Temporarily install 5 new lock plates and the 10 bolts.
After the ring gear cools down, diametrically tighten the 10 bolts uniformly in several passes.
![]() |
Using a chisel and hammer, stake the 5 lock plates.
| 3. INSTALL REAR DIFFERENTIAL CASE BEARING |
![]() |
Using SST and a press, press the 2 case bearings (inner) onto the differential case.
| 4. INSPECT DIFFERENTIAL RING GEAR RUNOUT |
![]() |
Install the differential case and 2 case bearings (outer) to the carrier, and install the 2 adjusting nuts so that there is no play in the bearing.
Install the 2 bearing caps with the 4 bolts.
Using a dial indicator, measure the runout of the ring gear.
Remove the 4 bolts, 2 bearing caps, 2 adjusting nuts and differential case.
| 5. INSTALL DIFFERENTIAL OIL STORAGE RING |
Using a brass bar and hammer, tap in a new oil storage ring.
| 6. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING |
![]() |
Using SST and a press, press the bearing (outer) into the carrier.
| 7. INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING |
![]() |
Using SST and a press, press the bearing (outer) into the carrier.
| 8. INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING |
Install the plate washer to the drive pinion.
![]() |
Using SST and a press, press the bearing (inner) onto the drive pinion.
| 9. ADJUST DIFFERENTIAL DRIVE PINION PRELOAD |
![]() |
Install the drive pinion, bearing (inner) and oil slinger.
![]() |
Using SST, install the companion flange.
| *a | Turn |
| *b | Hold |
Adjust the drive pinion preload by installing the drive pinion nut.
![]() |
Using SST to hold the companion flange in place, tighten the nut.
Using a torque wrench, measure the preload.
| Bearing | Specified Condition |
| New bearing | 1.0 to 1.5 N*m (11 to 15 kgf*cm, 9 to 13 in.*lbf) |
| Reused bearing | 0.5 to 0.7 N*m (6 to 7 kgf*cm, 5 to 6 in.*lbf) |
| 10. INSTALL DIFFERENTIAL CASE ASSEMBLY |
![]() |
Apply MP grease to the rack of the shift fork and connecting part of the indicator switch.
![]() | MP grease |
Insert the shift fork into the differential carrier as shown in the illustration.
![]() |
Place the outer race and adjusting nut on the left side of the sleeve.
![]() |
Insert the shift fork into the groove of the sleeve while holding the sleeve by hand, and install the case to the carrier.
| 11. INSTALL REAR DIFFERENTIAL BEARING ADJUSTING NUT |
![]() |
Install the 2 adjusting nuts to the carrier, making sure the nuts are threaded properly.
| 12. INSPECT AND ADJUST DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION BACKLASH |
![]() |
Align the matchmarks on the cap and carrier.
| *1 | Matchmark |
![]() |
Install the right and left bearing caps with the 4 bolts.
![]() |
Loosen the 4 bearing cap bolts to the point where the adjusting nuts can be turned by SST.
| *a | for LH Side |
| *b | for RH Side |
Using SST, tighten the adjusting nut on the ring gear side until the ring gear has a backlash of about 0.2 mm (0.00787 in.).
While turning the ring gear, use SST to tighten the adjusting nut on the drive pinion side. After the bearings have settled, loosen the adjusting nut on the drive pinion side.
Using SST, tighten the adjusting nut 1 to 1.5 notches from the 0 preload position.
![]() |
Using a dial indicator, adjust the ring gear backlash until it is within the specification.
![]() |
Tighten the bearing cap bolts.
| 13. INSPECT TOTAL PRELOAD |
![]() |
Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.
| Bearing | Specified Condition |
| New | 0.4 to 0.5 N*m (4 to 6 kgf*cm, 4 to 5 in.*lbf) + drive pinion preload |
| Reused | 0.4 to 0.5 N*m (4 to 6 kgf*cm, 4 to 5 in.*lbf) + drive pinion preload |
| 14. INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION |
![]() |
Coat 3 or 4 teeth at 3 different positions on the ring gear with Prussian blue.
Hold the companion flange firmly in place and rotate the ring gear in both directions.
Inspect the tooth contact pattern.

![]() |
| *1 | Plate Washer |
| Thickness mm (in.) | Thickness mm (in.) |
| 1.69 to 1.71 (0.0666 to 0.0673) | 2.02 to 2.04 (0.0796 to 0.0803) |
| 1.72 to 1.74 (0.0678 to 0.0685) | 2.05 to 2.07 (0.0807 to 0.0814) |
| 1.75 to 1.77 (0.0689 to 0.0696) | 2.08 to 2.10 (0.0819 to 0.0826) |
| 1.78 to 1.80 (0.0701 to 0.0708) | 2.11 to 2.13 (0.0831 to 0.0838) |
| 1.81 to 1.83 (0.0713 to 0.0720) | 2.14 to 2.16 (0.0843 to 0.0850) |
| 1.84 to 1.86 (0.0725 to 0.0732) | 2.17 to 2.19 (0.0855 to 0.0862) |
| 1.87 to 1.89 (0.0737 to 0.0744) | 2.20 to 2.22 (0.0867 to 0.0874) |
| 1.90 to 1.92 (0.0748 to 0.0755) | 2.23 to 2.25 (0.0878 to 0.0885) |
| 1.93 to 1.95 (0.0760 to 0.0767) | 2.26 to 2.28 (0.0890 to 0.0897) |
| 1.96 to 1.98 (0.0772 to 0.0779) | 2.29 to 2.31 (0.0902 to 0.0909) |
| 1.99 to 2.01 (0.0784 to 0.0791) | 2.32 to 2.34 (0.0914 to 0.0921) |
| 15. REMOVE REAR DRIVE PINION NUT |
![]() |
Using SST and a hammer, loosen the staked part of the nut.
![]() |
Using SST to hold the companion flange in place, remove the nut.
| *a | Turn |
| *b | Hold |
| 16. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR |
![]() |
Using SST, remove the companion flange with dust deflector.
| 17. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER |
![]() |
Remove the oil slinger from the drive pinion.
| 18. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING |
![]() |
Using SST, remove the roller bearing (inner).
![]() |
Using SST, tap out the roller bearing (outer).
| 19. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER |
![]() |
Install a new bearing spacer.
| 20. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING |
![]() |
Install the bearing (inner) to the drive pinion.
| 21. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER |
![]() |
Install the oil slinger to the drive pinion.
| 22. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL |
Apply MP grease to the lip of the oil seal.
![]() |
Using SST and a hammer, tap in a new seal.
| *a | Oil Seal Depth |
| 23. INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR |
![]() |
Using SST, install the companion flange with dust deflector.
Apply hypoid gear oil LSD to drive pinion thread and nut seat face.
![]() |
Using SST to hold the companion flange in place, install a new nut.
| *1 | Turn |
| *1 | Hold |
| 24. INSPECT TOTAL PRELOAD |
Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.
![]() |
Using a torque wrench, measure the total preload.
| Bearing | Specified Condition |
| New bearing | 1.1 to 1.6 N*m (12 to 16 kgf*cm, 10 to 14 in.*lbf) + ring gear preload |
| Reused bearing | 0.6 to 0.8 N*m (7 to 8 kgf*cm, 6 to 7 in.*lbf) + ring gear preload |
| 25. INSPECT DIFFERENTIAL RING GEAR BACKLASH |
![]() |
Using a dial indicator, measure the backlash of the ring gear.
| 26. INSPECT REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the runout of the companion flange vertically and laterally.
| *a | 30 mm (1.18 in.) |
| Item | Specified Condition |
| Vertical runout | 0.10 mm (0.00394 in.) |
| Lateral runout | 0.10 mm (0.00394 in.) |
| 27. STAKE DRIVE PINION NUT |
![]() |
Using a chisel and hammer, stake the nut.
| 28. INSTALL REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK |
![]() |
Install 2 new adjusting nut locks to the bearing caps with the 2 bolts.
Bend the nut locks.
| 29. INSTALL REAR DIFFERENTIAL LOCK SHIFT FORK SHAFT |
![]() |
Apply MP grease to the outer circuit of the fork shaft.
| *1 | Groove |
| *2 | Hole |
Install the fork shaft so that the hole of the shift fork aligns with that of the shift fork shaft.
![]() |
Remove any seal packing material.
| *1 | Seal packing |
Apply seal packing to the carrier as shown in the illustration.
![]() |
Clean the threads of the bolts and retainer bolts holes with toluene or trichloroethylene.
Apply adhesive to 2 or 3 threads at the end of the mounting bolt.
Tighten the shaft retainer with the 2 bolts.
![]() |
Using a 5 mm pin punch and hammer, tap in the slotted spring pin to the shift fork.
![]() |
Shift the fork to the lock side.
| *1 | Lock |
![]() |
Install the steel ball, spring and spring seat.
| *1 | Steel Ball |
| *2 | Spring |
| *3 | Spring Seat |
| *4 | Screw Plug |
Clean the threads of the 2 plug holes with toluene or trichloroethylene.
Apply adhesive to the plug threads.
Using a 6 mm hexagon wrench, install the screw plugs.
| 30. INSPECT REAR DIFFERENTIAL LOCK SLEEVE |
![]() |
Measure the distance between the sleeve and tip of the differential case when the differential is free, and when it is locked.
| Position | Specified Condition |
| Lock | 17.44 to 18.86 mm (0.6866 to 0.7425 in.) |
| Free | 32.40 to 33.90 mm (1.2756 to 1.3346 in.) |
| 31. INSTALL NO. 4 TRANSFER INDICATOR SWITCH |
![]() |
Install the indicator switch and a new gasket.
Connect the connector.
| 32. INSTALL DIFFERENTIAL LOCK SHIFT ACTUATOR |
![]() |
Install a new O-ring to the actuator.
| *1 | Shift Fork |
| *2 | Actuator Installation Hole |
![]() | Outside |
Install the actuator with the bolt and nut.
Check that the outermost rack tooth of the shift fork is almost directly above the center line of the actuator installation hole.
![]() |
Check that the matchmarks on the pinion of the actuator are in the range between 2 and 8° clockwise of the center line of the actuator.
| *1 | Matchmark |
| *a | 5° |
| *b | 108° |
| *c | 1.5 V |
Install a new O-ring to the actuator.
Apply a light coat of gear oil to the O-ring.
Apply MP grease to the gear parts.
![]() |
Check that the outermost rack tooth of the shift fork aligns with the matchmarks on the pinion of the actuator.
| *1 | Knock Pin |
Install the actuator so that the long hole in the actuator fits with the knock pin on the carrier.
Rotate the actuator counterclockwise so that the knock pin slides to the end of the hole as shown in the illustration.
Install the bolts.
![]() |
Connect the breather hose.
Connect the connector.