Home › SUSPENSION & AXLE › AXLE › FRONT AXLE HUB

FRONT AXLE HUB > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL PLUG (for Pre-Runner)


C119749
  1. Using a brass bar and hammer, tap in the plug.



2. INSTALL FRONT AXLE HUB OIL SEAL


F042762E01
  1. Using a brass bar and hammer, tap in a new oil seal.

    NOTICE:
    Do not damage the spacer.



3. INSTALL FRONT AXLE BEARING ASSEMBLY (for 4WD)


C098702E01
  1. Using SST and a press, press a new bearing into the axle hub.

    SST
    09649-17010  

  1. w/ ABS:
    Install the ABS speed sensor rotor and spacer to the axle hub.

  1. w/o ABS:
    Install the 2 spacers to the axle hub.



4. INSTALL FRONT AXLE BEARING ASSEMBLY (for Pre-Runner)


C098702E01
  1. Using SST and a press, press a new bearing into the axle hub.

    SST
    09649-17010  

  1. Install the ABS speed sensor rotor to the axle hub.



    C119748E01
  1. Using SST, install a new adjusting nut.

    SST
    09318-12010  

    Torque:
    274 N*m{ 2,794 kgf*cm , 202 ft.*lbf }



5. INSTALL FRONT AXLE HUB ASSEMBLY


F042759E01
  1. Apply MP grease to a new O-ring.

  1. Install the O-ring to the axle hub.

  1. Install the dust cover and axle hub to the steering knuckle with the 4 bolts.

    Torque:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }



6. INSTALL FRONT AXLE HUB NUT (for 4WD)


F042732E01
  1. Install the hub nut.

    Torque:
    235 N*m{ 2,396 kgf*cm , 173 ft.*lbf }

  1. Install the lock cap and a new cotter pin.

    NOTICE:
    If the holes for the cotter pin are not aligned, tighten the nut an additional 60°.



7. INSTALL FRONT AXLE HUB GREASE CAP (for 4WD)
  1. Install a new grease cap to the axle hub.



8. INSTALL FRONT DISC


9. INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY


F050211E01
  1. Install the disc brake cylinder with the 2 bolts.

    Torque:
    123 N*m{ 1,254 kgf*cm , 91 ft.*lbf }



    F042731E01
  1. Connect the brake tube bracket to the steering knuckle with the bolt.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



    F051151E01
  1. Using SST, connect the brake tube to the disc brake cylinder.

    SST
    09023-00101  

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf } for use without SST
    14 N*m{ 143 kgf*cm , 10 ft.*lbf } for use with SST

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).



10. INSTALL FRONT SPEED SENSOR LH (w/ ABS)


F042730E03
  1. Install the speed sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

  1. Connect the 2 clamps.

  1. Connect the speed sensor wire harness to the steering knuckle with the bolt.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



11. INSTALL FRONT WHEEL

Torque:
105 N*m{ 1,071 kgf*cm , 77 ft.*lbf }



12. CHECK ABS SPEED SENSOR SIGNAL (w/ ABS)
  1. Check the ABS speed sensor signal (Click here).