METER / GAUGE SYSTEM > Seat Belt Warning Light for Passenger Seat does not Flash |


| 1.CHECK HARNESS AND CONNECTOR (ACCESSORY METER ASSEMBLY OR TELLTALE LIGHT ASSEMBLY - BATTERY AND GROUND) |
w/ Accessory Meter:
Disconnect the A43 accessory meter assembly connector.
Measure the voltage of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
| A43-12 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| A43-12 (IG) - Body ground | Ignition switch OFF | Below 1 V |
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| A43-1 (GND1) - Body ground | Below 1 Ω |
w/o Accessory Meter:
Disconnect the P16 telltale light connector.
Measure the voltage of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
| P16-3 - Body ground | Ignition switch ON | 11 to 14 V |
| P16-3 - Body ground | Ignition switch OFF | Below 1 V |
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| P16-1 - Body ground | Below 1 Ω |
|
| ||||
| OK | |
| 2.INSPECT FRONT SEAT INNER BELT ASSEMBLY (BUCKLE SWITCH) |
![]() |
Disconnect the F12 front seat inner belt assembly connector.
Measure the resistance of the buckle switch.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Seat belt is unfastened (ON) and apply more than 147 N (15 kgf, 22 lbf) of force to occupant detection sensor | Below 100 Ω |
| 1 - 2 | Seat belt is fastened (OFF) | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (INNER BELT - BODY GROUND) |
![]() |
Disconnect the F12 front seat inner belt assembly connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| F12-2 - Body ground | Below 1 Ω |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (ACCESSORY METER ASSEMBLY OR TELLTALE LIGHT ASSEMBLY - BATTERY AND GROUND) |
w/ Accessory Meter:
Disconnect the F12 front seat inner belt assembly connector.
Disconnect the A43 accessory meter assembly connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| F12-1 - A43-8 (PBEW) | Below 1 Ω |
| F12-1 - Body ground | 10 kΩ or higher |
w/o Accessory Meter:
Disconnect the F12 front seat inner belt assembly connector.
Disconnect the P16 telltale light assembly connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| F12-1 - P16-3 | Below 1 Ω |
| F12-1 - Body ground | 10 kΩ or higher |
| Result | Proceed to |
| OK (w/ Accessory meter) | A |
| OK (w/o Accessory meter) | B |
| NG | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 5.INSPECT FRONT SEAT INNER BELT ASSEMBLY (OCCUPANT DETECTION SENSOR) |
![]() |
Disconnect the A sensor connector.
Measure the resistance of the sensor.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Apply more than 147 N (15 kgf, 22 lbf) of force to occupant detection sensor | Below 100 Ω |
| 1 - 2 | No force applied to occupant detection sensor | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||