Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

DTC    B2416    Height Control Sensor Malfunction

DTC    B241A    Rear Height Control Sensor

for Preparation Click here


DESCRIPTION

The headlight leveling ECU receives signals indicating the height of the vehicle from the rear height control sensor.

DTC Code
DTC Detection Condition
Trouble Area
B2416
  1. Malfunction in the rear height control sensor.
  2. Open or short in the rear height control sensor circuit.
  1. Rear height control sensor sub-assembly LH
  2. Harness or connector
  3. Headlight leveling ECU assembly
B241A

WIRING DIAGRAM


E225964E02


INSPECTION PROCEDURE

HINT:
After replacing the headlight leveling ECU and rear height control sensor, initialization of the ECU is necessary (Click here).

1.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2416 or B241A output does not occur.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.READ VALUE USING INTELLIGENT TESTER (REAR HEIGHT CONTROL SENSOR)
  1. Using the intelligent tester, read the Data List (Click here).

    HL Auto Leveling 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Height Sens Pw Supply Val
    Rear height control sensor power supply value / 0 to 5 V
    Approximately 5.0 V
    -
    Rr Height Sens Signal Val
    Rear height control sensor signal value / 0 to 5 V
    Approximately 2.5 V (When vehicle level)
    The value changes according to the vehicle height.

    OK:
    The display is as specified in the normal condition column.



NG
Go to step 3
OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY (Click here)  

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH)
  1. Disconnect the H17 headlight leveling ECU connector.

  1. Disconnect the R22 rear height control sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H17-12 (SBR) - R22-3 (SHB)
    Always
    Below 1 Ω
    H17-19 (SHRL) - R22-2 (SHRR)
    Always
    Below 1 Ω
    H17-21 (SGR) - R22-1 (SHG)
    Always
    Below 1 Ω
    H17-12 (SBR) - Body ground
    Always
    10 kΩ or higher
    H17-19 (SHRL) - Body ground
    Always
    10 kΩ or higher
    H17-21 (SGR) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH


    E225436E01
  1. Remove the rear height control sensor (Click here).

  1. Connect 3 dry cell batteries (1.5 V) in series.

  1. Connect the positive (+) end of the batteries to terminal 3 (SHB) of the rear height control sensor and the negative (-) end of the batteries to terminal 1 (SHG). While slowly moving the sensor link up and down, measure the voltage between terminal 2 (SHRR) and terminal 1 (SHG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    2 (SHRR) - 1 (SHG)
    High (+)
    4.34 to 4.6 V
    Normal
    3.0 to 3.3 V
    Low (-)
    0.4 to 0.66 V

    Text in Illustration 
    *a
    Low (-)
    *b
    43°
    *c
    Normal
    *d
    105.7°
    *e
    High (+)

    NOTICE:
    1. Do not apply a voltage of more than 6 V.
    2. Do not drop the height control sensor. If it is dropped, replace it with a new one.



NG
REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (Click here)
OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY (Click here)