Home › RESTRAINTS › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY

FRONT SEAT OUTER BELT ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY


B127517
  1. Insert the tip of the adjuster to the pillar, and align the adjuster's bolt hole with the pillar's bolt hole.

  1. Install the bolt as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



2. INSTALL SHOULDER BELT ANCHORAGE PLATE COVER


B087816E03
  1. Install the plate cover as shown in the illustration.

    HINT:
    Make sure the plate cover is firmly set into the garnish's claws.



3. INSTALL CENTER PILLAR GARNISH RH


B127515E02
  1. Attach the claw and clip to install the garnish.



4. INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH


B084922E03

NOTICE:
Do not disassemble the retractor.

  1. w/o Pretensioner:
    Align the claws with the seat belt positioning holes and install the retractor of the outer belt with the bolt as shown in the illustration.

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 ft.*lbf }



    B120576
  1. w/ Pretensioner:

    1. Align the claws with the seat belt positioning holes and install the retractor of the outer belt with the bolt as shown in the illustration.

      Torque:
      4.8 N*m{ 49 kgf*cm , 42 in.*lbf }



    2. B114993
    3. Connect the pretensioner connector as shown in the illustration.



    B084920E02
  1. Connect the outer belt with the shoulder anchor's bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Attach the 4 claws to install the seat belt anchor cover cap.



5. INSTALL CENTER PILLAR GARNISH LOWER RH


    B085693E02
  1. w/o Pretensioner:
    Connect the anchor of the outer belt with the built-in bolt after installing the center pillar garnish lower.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B127518
  1. w/ Pretensioner:
    Connect the anchor of the outer belt with the built-in bolt after installing the center pillar garnish lower.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B089695E01
  1. Attach the 2 claws to install the lap belt outer anchor cover.



6. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure described for the LH side.



7. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure described for the LH side.



8. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure described for the LH side.



9. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure described for the LH side.



10. INSTALL FRONT SEAT ASSEMBLY RH
  1. Place the seat in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. w/ Seat belt warning, w/ occupant detection sensor:
    Connect the connector under the seat.



    B126651E01
  1. Install the seat with the 4 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.



11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).